Tobinpridgen3484
This study aimed to compare the tissue reaction of two repair materials for furcation perforations, nano-filled resin modified glass ionomer (Nano-FRMGI) and mineral trioxide aggregate (MTA), used with or without an artificial floor.
A total of 96 teeth in 6 dogs were used for this study. After access cavities, root canals were prepared and obturated with gutta percha using cold lateral condensation technique. Perforations were then created on the floors of the pulp chambers. The perforations divided into four groups n=24/group that were sealed with MTA alone, MTA with calcium sulphate artificial floor (CSAF), FRMGI alone and Nano-FRMGI with CSAF. All access cavities were filled with composite resin. Two dogs were sacrificed at 1, 3, and 6 month. The experimental tooth along with the surrounding alveolar bone were cut in block sections and histologically evaluated for tissue response. Data were analyzed by Chi-square (P≤0.05).
MTA and MTA with CSAF showed more bone and cementum apposition when compared to Nano-FRMGI at 6-month interval. MTA and MTA with CSAF showed less bone resorption, epithelium proliferation and inflammation compared to Nano-FRMGI at 6-month interval.
MTA with CSAF or MTA-alone show better outcomes in the repair of pulp chamber floor perforation.
MTA with CSAF or MTA-alone show better outcomes in the repair of pulp chamber floor perforation.
This study aimed to assess the resistance of roots to fracture after being root canal filled with two types of endodontic sealers; bio-ceramic based sealer (TotalFill) and epoxy-resin based sealer (AH Plus).
Fifty-nine single canal mandibular premolars were instrumented. Group I (n=14, negative control) root canals were left without instrumentation and unfilled, group II (n=15, positive control) root canals were instrumented only and left unfilled, group III and IV (n=15 each) root canals were instrumented and filled with either gutta-percha/TotalFill or gutta-percha/AH Plus, respectively. The resistance of the roots to fracture was measured with a universal testing machine "Instron Corp" through recording the maximum force in Newton (N) needed to fracture each root. To analyze the data Kruskal-Wallis test was utilized, followed by Dunn's Bonferroni post hoc test for multiple comparisons. The level of significance was set at 0.05 (P≤0.05).
TotalFill group showed slightly better fracture resistance (734.62 N) than AH Plus group (728.29 N). However, no statistical significant difference was found between the two groups (P>0.05). The greatest mean fracture force was shown in the negative control group (913.915 N) with statistical significant difference between the other three groups (P<0.05).
Gutta-percha/TotalFill and gutta-percha/AH Plus did not reinforce the root canal treated teeth.
Gutta-percha/TotalFill and gutta-percha/AH Plus did not reinforce the root canal treated teeth.
Initial setting time is one of the most important properties of calcium silicate cements (CSCs) such as white mineral trioxide aggregate (WMTA). This study aimed to evaluate the effect of two methods used to reduce the particle size of WMTA, mechanical activation and chemical synthesis.
WMTA without bismuth oxide (WMTA-B) was provided and divided into four groups (n=5) including WMTA-B, WMTA-B+10 min milling, WMTA-B+30 min milling, and sol-gel. In groups 2 and 3, the milling was performed by using tungsten carbide balls in a ratio 115 (w/w) and a vibration frequency of 30 Hz together with absolute ethanol. find more For the fourth group, polyethylene glycol (PEG), calcium acetate (Ca(C
H
O
)
), SiO
, and aluminum oxide (Al
O
) were used for the sol-gel process. After preparation, sample powders were mixed with distilled water and placed in cylindrical molds, covered with water-moistened gauze, and incubated at 37°C for 24 hours. The Vicat needle test analyzed the initial setting time. Data were analyzed by ANOVA and Tukey tests at a significance level of P<0.05. The correlation between particle size and setting time was determined.
Initial setting time of the sol-gel and WMTA-B+30 min milling was significantly lower than in the other two groups (P<0.05). A significant correlation was noticed between particle size and initial setting time (P<0.05).
Sol-gel process introduces a promising alternative strategy for the reduction of initial setting time of CSC materials. While both methods increased surface area, mechanical activation was not as successful in reducing surface area and initial setting time as effectively as the sol-gel process.
Sol-gel process introduces a promising alternative strategy for the reduction of initial setting time of CSC materials. While both methods increased surface area, mechanical activation was not as successful in reducing surface area and initial setting time as effectively as the sol-gel process.
The purpose of this laboratory-based study was to compare the shaping forces and torques developed by the XP Shaper (FKG Dentaire SA, La Chaux-de-fonds, Switzerland) and OneCurve (Micro-Mega, Besancon, France) systems during shaping of narrow canals.
Mandibular premolars with a single canal were divided equally into two groups; XP Shaper and OneCurve (n=16 each). In both groups, the canals were shaped with XP Shaper file (30/01) or OneCurve file (25/O6) that was inserted three times until it reached the canal length. The tooth was surrounded by water under controlled simulated intracanal temperature throughout the experiment. The inward and outward peak forces and the peak torques were recorded and analyzed statistically using the Mann-Whitney test. The shaping times were analyzed using Student's t-test. The significance level was set at 5%.
In both groups, the developed forces in both directions and the torques increased with the successive insertions of the file. In the two groups, the inward peak forces ranged from 0.33 to 3.12 N, while the outward peak forces ranged from 0.09 to 1.96 N. In the three insertions, the XP Shaper showed significantly lower peak forces in both directions. The peak torque developed in both groups ranged from 0.12 to 1.52 N.cm. XP Shaper had significantly lower torque values in all the insertions than OneCurve. The XP Shaper system was able to completely shape the canals in 33.4 seconds while the OneCurve system was able to completely shape the canals in 32.8 seconds.
The XP Shaper system showed favorably lower force and torque values during canal shaping compared with the OneCurve system.
The XP Shaper system showed favorably lower force and torque values during canal shaping compared with the OneCurve system.
