Sheamclamb3651

44 per day and 0.34 per day, respectively.A fiber-network chitosan film with three-dimensional interconnected structure was prepared in an alkali/urea solution and regenerated from an ethanol/water coagulation solution. The surface morphology and structure were characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD), N2 adsorption-desorption, attenuated total reflection Fourier transform infrared spectroscopy (ATR-FTIR) and X-ray photoelectron spectroscopy (XPS). Batch adsorption for uranium U(VI) was conducted to investigate the effects of pH, contact time and initial uranium concentration on adsorption capacity. The adsorption of CS-80% was in good agreement with the pseudo-second-order kinetic model and Langmuir isotherm model. The three-dimensional interconnected structure provided more active sites and favored the diffusion of uranium solute, and therefore enhanced the adsorption capacity. The maximum adsorption capacity at pH 5 was 196.735 mg/g. The adsorption mechanism was attributed to chelation and coordination of uranium with -NH2 and -OH groups on chitosan molecules.Understanding the factors that affect the occurrence of failures in urban drainage networks (UDNs) is a key concept for developing strategies to improve the reliability of such systems. Although a lot of research has been done in this field, the relationship between UDN structure (i.e. layout) and its functional failures is still unclear. In this context, the present study focuses first on determining which are the most common sewer layout topologies, based on a data set of 118 UDNs, and then on analyzing the relationship between these and the occurrence of node flooding using eight subnetworks of the sewer system of Dresden, Germany, as a study case. A method to 'quantify' the topology of a UDN in terms of similarity to a branched or meshed system, referred to as Meshness, is introduced. Results indicate, on the one hand, that most networks have branched or predominantly branched topologies. On the other hand, node flooding events in networks with higher Meshness values are less likely to occur, and have shorter durations and smaller volumes than in predominantly branched systems. Predominantly meshed systems are identified then as more reliable in terms of flooded nodes and flooding volumes.Magnetic laccase nanoflowers (MNFs-Lac) were successfully prepared through encapsulating Fe3O4 magnetic nanoparticles into the interior of laccase nanoflowers by grafting N-(phosphonomethyl)iminodiacetic acid (PMIDA) as an interconnecting bridge between the magnetic nanoparticles and copper ions. The characterizations by scanning electron microscopy and transmission electron microscopy showed that MNFs-Lac were spherical, porous and flower-like crystals with diameters of ∼10 μm, and Fe3O4 nanoparticles were encapsulated in the interior of MNFs-Lac evenly. The enzymatic activity and reusability of MNFs-Lac were evaluated based on the degradation efficiency for malachite green (MG). The degradation parameters, concerning initial MG concentration, dosage of MNFs-Lac, reaction temperature, pH value and reaction time, were optimized through single-factor experiments. Under the optimal conditions, 25 mg·L-1 MG can be degraded almost completely by 1.5 g·L-1 MNFs-Lac within 15 min. When the MNFs-Lac were reused for 18 times, the degradation efficiency of MG was still as high as 90%. These results suggested that the modified preparation method improved greatly the reusability of MNFs-Lac, which made them more suitable to degrade MG in a water environment.Food industry wastewater (FIWW) streams with high organic content are among the most suitable and inexpensive candidates for polyhydroxyalkanoate (PHA) biopolymer production. Due to its high organic acid content, pickle industry wastewater (PIWW), can be considered as one of the prospective alternatives to petroleum-based polymers for PHA production. In this context, this study aimed to investigate the production of PHA with enriched microbial culture using PIWW. Two laboratory scale sequencing batch reactors (SBRs) were operated under aerobic dynamic feeding conditions at a sludge retention time of 8 days, with a total cycle duration of 24 hours. SBRs were fed with peptone mixture and PIWW. In-cycle analysis and batch respirometric tests were performed to evaluate PHA storage together with biodegradation kinetics. In-cycle analysis showed that maximum PHA content was 1,820 mgCOD/L, corresponding to 44% in the biomass (ratio of chemical oxygen demand (COD) to volatile suspended solids) for PIWW. buy Idasanutlin Experimental results were also confirmed with activated sludge model simulations. As for the PHA composition, hydroxybutyrate was the major fraction. Model simulations proposed a unique conversion-degradation-storage pathway for the organic acid mixture. This paper presents a novel insight for better understanding of PHA biopolymer production using high saline FIWW.Phosphonates are widely used in various industries. It is desirable to remove them before discharging phosphonate-containing wastewater. This study describes a large number of batch experiments with adsorbents that are likely suitable for the removal of phosphonates. For this, adsorption isotherms for four different granular ferric hydroxide (GFH) adsorbents were determined at different pH values in order to identify the best performing material. Additionally, the influence of temperature was studied for this GFH. A maximum loading for nitrilotrimethylphosphonic acid (NTMP) was found to be ∼12 mg P/g with an initial concentration of 1 mg/L NTMP-P and a contact time of 7 days at room temperature. Then, the adsorption of six different phosphonates was investigated as a function of pH. It was shown that GFH could be used to remove all investigated phosphonates from water and, with an increasing pH, the adsorption capacity decreased for all six phosphonates. Finally, five adsorption-desorption cycles were carried out to check the suitability of the material for multiple re-use. Even after five cycles, the adsorption process still performed well.Membrane bioreactor (MBR) models are useful tools for both design and management. The system complexity is high due to the involved number of processes which can be clustered in biological and physical ones. Literature studies are present and need to be harmonized in order to gain insights from the different studies and allow system optimization by applying a control. This position paper aims at defining the current state of the art of the main integrated MBR models reported in the literature. On the basis of a modelling review, a standardized terminology is proposed to facilitate the further development and comparison of integrated membrane fouling models for aerobic MBRs.