Schulzlogan8388

Functionalities of 3D printing filaments have gained much attention owing to their properties for various applications in the last few years. Innovative biocomposite 3D printing filaments based on polylactic acid (PLA) composited with ZnO nanoflowers at varying contents were successfully fabricated via a single-screw extrusion technique. The effects of the varying ZnO nanoflower contents on their chemical, thermal, mechanical, and antibacterial properties were investigated using Fourier transform infrared spectroscopy (FTIR), differential scanning calorimetry (DSC), and tensile testing, as well as qualitative and quantitative antibacterial tests, respectively. It was found that the ZnO nanoflowers did not express any chemical reactions with the PLA chains. The degrees of the crystallinity of the PLA/ZnO biocomposite filaments increased when compared with those of the neat PLA, and their properties slightly decreased when increasing the ZnO nanoflower contents. Additionally, the tensile strength of the PLA/ZnO biocomposite filaments gradually decreased when increasing the ZnO nanoflower contents. The antibacterial activity especially increased when increasing the ZnO nanoflower contents. Additionally, these 3D printing filaments performed better against Gram-positive (S. aureus) than Gram-negative (E. coli). This is probably due to the difference in the cell walls of the bacterial strains. The results indicated that these 3D printing filaments could be utilized for 3D printing and applied to medical fields.Silver nanoparticles (AgNPs) are novel materials with antibacterial, antifungal, and antiviral activities over a wide range. This study aimed to prepare polyvinylpyrrolidone (PVP) electrospinning composites with uniformly distributed AgNPs. In this study, starch-capped ~2 nm primary AgNPs were first synthesized using Atmospheric pressure Pulsed Discharge Plasma (APDP) at AC 10 kV and 10 kHz. Then, 0.6 wt.% AgNPs were mixed into a 10 wt.% PVP ethanol-based polymer solution and coiled through an Ultrasonic-assisted Electrospinning device (US-ES) with a 50 W and 50 kHz ultrasonic generator. At 12 kV and a distance of 10 cm, this work successfully fabricated AgNPs-PVP electrospun fibers. The electrospun products were characterized using Scanning Electron Microscopy (SEM), Transmission Electron Microscopy (TEM), High-Resolution TEM (HR-TEM), Fourier Transform Infrared Spectroscopy (FT-IR), X-ray Diffraction (XRD), Thermogravimetric (TG), and X-ray Photoelectron Spectroscopy (XPS) methods.Polyelectrolytes are polymers with repeating units of ionizable groups coupled with counterions. LJI308 S6 Kinase inhibitor Recently, polyelectrolytes have drawn significant attention as highly promising macromolecular materials with potential for applications in almost every sector of our daily lives. Dyes are another class of chemical compounds that can interact with substrates and subsequently impart color through the selective absorption of electromagnetic radiation in the visible range. This overview begins with an introduction to polyelectrolytes and dyes with their respective definitions, classifications (based on origin, molecular architecture, etc.), and applications in diverse fields. Thereafter, it explores the different possible interactions between polyelectrolytes and dyes, which is the main focus of this study. The various mechanisms involved in dye-polyelectrolyte interactions and the factors that influence them are also surveyed. Finally, these discussions are summarized, and their future perspectives are presented.The connection with textiles is one of the oldest traditions in humanity, and in the historical scenario, textiles and clothing deal with material culture. Therefore, preservation is of the utmost importance to keep this important heritage. Packaging and protection of museological textiles is imperative due to the risks that these articles suffer, mainly concerning the attack of microorganisms that promote the acceleration of their degradation, and it is still necessary to create a proper packing material. In the present work we describe a bibliographic review about the museological scenario, focused on the packaging for preservation of textile articles, as well as the techniques usually used in preventive material conservation. Future perpsctives for the improvement in the conservation of museological textiles are also given. This research aims to produce a sustainable material based on polycaprolactone (PCL), with and without antimicrobial function by incorporating Lavandula luisieri essential oil (EO), in the form of a non-woven substrate for museological packaging. A comparison was made with the most frequently used materials, such as raw cotton and a non-woven polyester. The results demonstrated that both PCL and PCL + EO obtained a good characterization for museological application with good breaking strength and excellent whiteness index. In addition, PCL + EO showed a high bacterial reduction when compared with other protective materials frequently used in museums. Therefore, these findings emphasize the potential use of this material as an innovative protective antibacterial museological packaging solution, able to safeguard and preserve textile museum and clothing collections for longer and for future generations.Several researchers have investigated the phenomenon of polymer-gas mixtures, and a few have proposed diffusion coefficient values instead of a diffusion coefficient model. There is a paucity of studies focused on the continuous change in the diffusion coefficient corresponding to the overall pressure and temperature range of the mixture. In this study, the gas sorption and desorption experiments of poly(methyl methacrylate) (PMMA) were conducted via solid-state batch foaming, and the weight change was measured using the gravimetric method with a magnetic balance. The control parameters were temperature, which ranged from 290 to 370 K, and pressure, which ranged from 2 to 5 MPa in the subcritical regime. Based on the experimental data, the diffusion coefficient of the PMMA was calculated using Fick's law. After calculating the diffusion coefficient in the range of the experiment, the diffusion coefficient model was employed using the least-squares method. Subsequently, the model was validated by comparing the obtained results with those in the literature, and the overall trend was found to be consistent. Therefore, it was confirmed that there were slight differences between the diffusion coefficient obtained using only Fick's equation and the value using by a different method.Anion exchange membrane fuel cells (AEMFCs) are considered superior to their counterpart proton exchange fuel cells due to their many advantages. Both fuel cells use membranes as polymer electrolytes to improve fuel-cell properties and power output. This work evaluates a series of imidazolium-quaternized poly(2,6-dimethyl-1,4-phenylene oxide) (ImPPO) functionalized zeolitic imidazole framework-8 (ZIF-8) (ImPPO/ZIF-8) as anion exchange membrane (AEM) electrolytes in a direct methanol alkaline fuel cell. FTIR and 1H NMR were used to confirm the successful membrane fabrication. SEM and TGA were used to study the morphological and thermal stability properties of the ImPPO/ZIF-8 membranes. The AEMs obtained in this work had contact angles ranging from 55.27-106.73°, water uptake from 9-83%, ion exchange capacity (IEC) from 1.93-3.15 mmol/g, and ion conductivity (IC) from 1.02-2.43 mS/cm. The best-performing membrane, ImPPO/3%ZIF-8, showed a water uptake of up to 35% at 80 °C, a swelling ratio of 15.1% after 72 h, IEC of 4.06 mmol/g, and IC of 1.96 mS/cm. A power density of 158.10 mW/cm2 was obtained. This makes ZIF-8 a good prospect as a filler for enhancing membrane properties.The great variability of cancer types demands novel drugs with broad spectrum, this is the case of Nisin, a polycyclic antibacterial peptide that recently has been considered for prevention of cancer cells growth. As an accepted food additive, this drug would be very useful for intestinal cancers, but the peptide nature would make easier its degradation by digestion procedures. For that reason, the aim of present study to investigate the protective effect of two different β-cyclodextrin-based nanosponges (carbonyl diimidazole and pyromellitic dianhydride) and their anti-cancer enhancement effect of Nisin-Z encapsulated with against colon cancer cells (HT-29). To extend its possible use, a comparison with breast (MCF-7) cancer cell was carried out. The physicochemical properties, loading efficiency, and release kinetics of Nisin complex with nanosponges were studied. Then, tricin-SDS-PAGE electrophoresis was used to understand the effect of NSs on stability of Nisin-Z in the presence of gastric peptidase pepsin. In addition, the cytotoxicity and cell membrane damage of Nisin Z were evaluated by using the MTT and LDH assay, which was complemented via Annexin-V/ Propidium Iodide (PI) by using flowcytometry. CD-NS are able to complex Nisin-Z with an encapsulation efficiency around 90%. A protective effect of Nisin-Z complexed with CD-NSs was observed in presence of pepsin. An increase in the percentage of apoptotic cells was observed when the cancer cells were exposed to Nisin Z complexed with nanosponges. Interestingly, Nisin Z free and loaded on PMDA/CDI-NSs is more selectively toxic towards HT-29 cells than MCF-7 cancer cells. These results indicated that nanosponges might be good candidates to protect peptides and deliver drugs against intestinal cancers.This study is focused on the characterization and investigation of polyvinylidene fluoride (PVDF) nanofibers from the point of view of macro- and nanometer level. The fibers were produced using electrostatic spinning process in air. Two types of fibers were produced since the collector speed (300 rpm and 2000 rpm) differed as the only one processing parameter. Differences in fiber's properties were studied by scanning electron microscopy (SEM) with cross-sections observation utilizing focused ion beam (FIB). The phase composition was determined by Fourier-transform infrared spectroscopy (FTIR) and Raman spectroscopy. The crystallinity was determined by differential scanning calorimetry (DSC), and chemical analysis of fiber's surfaces and bonding states were studied using X-ray photoelectron spectroscopy (XPS). Other methods, such as atomic force microscopy (AFM) and piezoelectric force microscopy (PFM), were employed to describe morphology and piezoelectric response of single fiber, respectively. Moreover, the wetting behavior (hydrophobicity or hydrophilicity) was also studied. It was found that collector speed significantly affects fibers alignment and wettability (directionally ordered fibers produced at 2000 rpm almost super-hydrophobic in comparison with disordered fibers spun at 300 rpm with hydrophilic behavior) as properties at macrolevel. However, it was confirmed that these differences at the macrolevel are closely connected and originate from nanolevel attributes. The study of single individual fibers revealed some protrusions on the fiber's surface, and fibers spun at 300 rpm had a core-shell design, while fibers spun at 2000 rpm were hollow.Filler effects on H2 permeation properties in sulfur-crosslinked ethylene propylene diene monomer (EPDM) polymers blended with two kinds of carbon black (CB) and silica fillers at different contents of 20 phr-60 phr are investigated by employing volumetric analysis in the pressure exposure range of 1.2 MPa~9.0 MPa. A linear relationship is observed between the sorbed amount and pressure for H2 gas, which is indicative of Henry's law behavior. The hydrogen solubility of EPDM composites increases linearly with increasing filler content. The magnitude of hydrogen solubility for the filled EPDM composites is dependent on the filler type. The hydrogen solubility is divided into two contributions hydrogen absorption in the EPDM polymer and hydrogen adsorption at the filler surface. Neat EPDM reveals pressure-dependent bulk diffusion behavior. However, with increasing filler content, the diffusivity for the filled EPDM composites is found to be independent of pressure. The magnitude of filler effects on the hydrogen permeation parameter is measured in the order of high abrasion furnace CB~semireinforcing furnace CB ˃ silica, whose effect is related to the specific surface area of CB particles and interfacial structure.