Raypetersen9618

[This corrects the article DOI 10.1021/acsomega.9b03750.].A silver-catalyzed dimerization of ethyl isocyanoacetates could trigger the tandem reaction of 3-(1-alkynyl) chromones under the basic condition in a one-pot reaction to afford xanthone skeletons with 2-imidazolyl substitution in an efficient manner. With the control experiment in hand, a mechanism including dimerization of isocyanoacetate/deprotonation/Michael addition/ring-opening/cyclization 1,2-elimination was deduced. Further investigation for the base was carried out, resulting in NaH as an optimal base to avoid the dimerization of 3-(1-alkynyl) chromones. The scope of this methodology was extended on the different substituents of 3-(1-alkynyl)-chromones and the potential of other N-heterocycle glycine ester anions to give the novel functional 2-nitrogen-derived xanthones.Thieno[2,3-c]isoquinolin-5(4H)-one is known for its potential as an anti-ischemic agent through the inhibition of poly(ADP-ribose) polymerase 1 (PARP1). However, the compound also inhibits many other enzymes of the PARP family, potentially limiting its usability. The broad inhibition profile, on the other hand, indicates that this molecule backbone could be potentially used as a scaffold for the development of specific inhibitors for certain PARP enzymes. These efforts call for novel synthetic strategies for substituted thieno[2,3-c]isoquinolin-5(4H)-one that could provide the needed selectivity. In this article, an efficient synthetic strategy for 8-alkoxythieno[2,3-c]isoquinolin-5(4H)-ones through eight steps is presented and other tested synthetic pathways are discussed in detail. read more Synthesis of 7-methoxythieno[2,3-c]isoquinolin-5(4H)-one is also demonstrated to show that the strategy can be applied widely in the syntheses of substituted alkoxythieno[2,3-c]isoquinolin-5(4H)-ones.Commercial chemical sunscreens have a high content of synthetic ultraviolet (UV) actives that have caused widespread damage to marine ecosystems and may have adverse health effects in humans. In the present work, safer bio-based sunscreens with lignin UV absorbers were developed to address this issue. Partly demethylated and otherwise altered kraft lignins, the so-called CatLignins with abundant phenolic hydroxyl auxochromes and catechol units, outperformed regular kraft lignins as sunscreen UV absorbers in terms of sun protection factor (UVB-SPF) and UVA-UVB transmittance. Converting lignins to nanoparticles significantly enhanced sunscreen performance. The best lignin sunscreen, containing nanoparticles of hardwood CatLignin, had a UV transmittance of only 0.5-3.8% over the entire UVA-UVB region compared to 2.7-51.1% of a commercial SPF 15 sunscreen. Lignin-based sunscreens are particularly suitable for dark-tinted SPF cosmetics.Vitamin D plays a key role in the maintenance of calcium/phosphate homeostasis and elicits biological effects that are relevant to immune function and metabolism. It is predominantly formed through UV exposure in the skin by conversion of 7-dehydrocholsterol (vitamin D3). The clinical biomarker, 25-hydroxyvitamin D (25-(OH)-D), is enzymatically generated in the liver with the active hormone 1,25-dihydroxyvitamin D then formed under classical endocrine control in the kidney. Vitamin D metabolites are measured in biomatrices by liquid chromatography-tandem mass spectrometry (LC-MS/MS). In LC-MS/MS, chemical derivatization (CD) approaches have been employed to achieve the desired limit of quantitation. Recently, matrix-assisted laser desorption/ionization (MALDI) has also been reported as an alternative method. However, these quantitative approaches do not offer any spatial information. Mass spectrometry imaging (MSI) has been proven to be a powerful tool to image the spatial distribution of molecules from the surface of biological tissue sections. On-tissue chemical derivatization (OTCD) enables MSI to image molecules with poor ionization efficiently. In this technical report, several derivatization reagents and OTCD methods were evaluated using different MSI ionization techniques. Here, a method for detection and spatial distribution of vitamin D metabolites in murine kidney tissue sections using an OTCD-MALDI-MSI platform is presented. Moreover, the suitability of using the Bruker ImagePrep for OTCD-based platforms has been demonstrated. Importantly, this method opens the door for expanding the range of other poor ionizable molecules that can be studied by OTCD-MSI by adapting existing CD methods.Systematic first-principles calculations are designed to investigate the interaction between isolated S8, lithium polysulfide (PS) Li2S n (n = 1-8, at different lithiated stages) clusters and two-dimensional (2D) graphdiyne (GDY) materials. By the calculations of their detailed interaction, we investigate the 2D GDY ability of trapping lithium PS clusters in order to evaluate the anchoring effect of 2D GDY materials for lithium-sulfur batteries. The theoretical results show that lithium PS intermediates/B-GDY systems have a moderate binding energy, indicating that the 2D B-GDY material is a suitable candidate for the anchoring materials of Li-S batteries. From the analysis of their charge density differences, the B-S σ bond and Li bond play an important role in the anchoring effect of 2D B-GDY substrates.A new approach is presented to overcome the disadvantages of oxidation and harsh sintering conditions of Cu nanoparticle (Cu NP) conductive inks simultaneously. In this process, oleylamine (OAM) adsorbed on particles was effectively eliminated via the reactive desorption by formic acid in alcohols; meanwhile, Cu ion was generated on the surface. The desorption of OAM resulted in more severe surface oxidation of Cu NPs. The oxide (Cu2O) and Cu2+ distributed on the Cu NP surface could be reduced to Cu(0) by NaBH4 solution and take on the role of soldering flux to weld particles into a blocky structure. With the compact coalescence of particles without oxides, the resistivity of metal patterns could fall below 20 μΩ·cm and exhibit proper adhesion. Thanks to the sintering of Cu NPs at ambient conditions, the conductive patterns could be facilely formed on thermosensitive substrates. As the oxide state of Cu would be reduced during sintering, the partially oxidized Cu nanoparticles could be directly applied to conductive inks.