Parsonsluna6511

Patio Door Lock Repairs

Over time, patio door wear and tear could cause lock malfunctions. There are a few simple steps you can follow to ensure the security of your uPVC door.

These quick fixes will ensure your home is secure no matter if you adjust the lock or clean the mechanism.

Clean the Lock

While patio doors are a great option to let in the outside and keep out the elements however, they can also pose a security risk if your lock isn't working as it should. With time, wear and tear, cold and hot weather dirt, and other debris can cause your patio door lock to become difficult to operate. With a little care you can ensure that your patio door's lock is always working properly.

It is important to first clean the patio door lock and all moving parts. patio door repair helps to get rid of any grime and coatings that may be preventing the lock from functioning in the way it should. Begin by wiping down all the moving parts of your patio door lock using a wet cloth. Then you can use a scouring paper or a rough damp cloth to scrub the dirt-infested areas of the door frame and frame. Then, wipe the entire lock using a dry cloth to remove any remaining dampness and allow it to air dry before using it again.

If your patio door is equipped with a pin-tumbler latch You can lubricate it by applying powdered Graphite to the key. You can also apply a Teflon lubricant like WD-40 Multi Use Product. This type of lubricant can be easy to apply, and doesn't break down over time. If you're unable find the right lubricant to use with your lock, use a pencil with larger tip. Put the pencil into the lock and jiggle it around to distribute the graphite.

Tracks for sliding patio doors require regular maintenance to ensure they're free of dirt, dust, and debris. These tracks are especially susceptible to ice and snow which can cause them become stuck or slack and make it difficult for your patio doors to open and close.

Sliding patio door track rails and rollers can be cleaned by removing dirty or damaged weather stripping and cleaning them before replacing it. The same applies for rollers on patio doors, which can be wiped down and sprayed with a non-stick lubricant in order to allow them to move freely.

Lubricate the moving parts

uPVC French Doors, similar to sliding patios, operate by using 3 to 4 or sometimes, 5 point locking mechanisms. These include the lock cylinder and handle which is operated by the key. They require maintenance and the lubrication of moving parts. This can be done using a thin oil however, never WD40. It is recommended to do it at least once per year.





If sagging hinges don't cause the problem, it could be that the door isn't aligned. It could be rubbing or catching the strike plate's opening in the frame. The solution is to remove the strike plate and then use an abrasive chisel to increase the size of the mortise it sits in. This will allow the latch to fit properly into the hole and stop it from hitting the frame.

While the cylinder is out of the way take a measurement of its width using a book or piece of wood that will fit in the adjustment screw gap above the lock. The outer dimension is measured from the outside of the door to the center cylinder. The inner dimension is measured from the center adjustment screw to the end of the cylinder.

Verify the width of the lock.

If your patio door latch is difficult to turn, even after cleaning and oiling it could be because it's not aligned with the strike plate. Make sure that your door is in a balanced position, and if the hinge screws are in good condition. In many instances, moving the strike plate upwards or downwards will fix the problem.

The latch may not engage properly when the strike of the lock is too small. In this situation you'll have to increase the hole using either a hammer or chisel, and then test the latch to make sure that it is able to engage the strike plate without rubbing against or catching on the frame of the door jamb.

It is important to identify the type of mortise lock you currently are using before you purchase the replacement. This can be done by looking at the end faceplate and observing whether it is round or square. Take a look at each screw hole in the existing lock, and note their size. This will aid you in finding an alternative lock that is the same size and will fit perfectly into your existing hole.

You'll need to locate the mortise lock and examine it for scratches, bends or other damage that needs to be fixed. A damaged or bent latch is more likely to break than one that hasn't been utilized often, so make sure to replace the lock with a new one that is secure when you spot any indications of wear or damage.

After you've determined the type of lock replacement you need, it's now time to begin the actual repair. Remove the old handle and spindle out of your patio door, and then put in the new one. Start by installing the inside handle. Align it with the spindle and then secure it in place using the two bolts or screws. Install the exterior handle following the interior handle. After you've completed these steps you can test the new handles to ensure that they are able to open and close with ease and that the latch is catching correctly when you strike the plate.

Check the Strike of the Door.

The door latch and strike plate are the two components of the lock that work to ensure that the latch locks the door. A misaligned strike plate or door latch will cause the latch to not latch the door properly. Fortunately, this issue is often easy to fix.

First, inspect the holes in the strike plate's receiving to ensure that they are clear of obstructions such as dirt or plastic plugs. Then loosen the screws that hold the strike plate in place, allowing it to move horizontally, but not removing it from the frame of your door. Adjust the strike plate to align its holes for receiving with the latch hooks of the door latch. Once the strike plate is adjusted, tighten the screws and test the door to determine if it shuts smoothly with the new adjustment.

These plates are difficult to reach for homeowners with sliding patio doors. However they are vital to lock and unlock your door. The metal plates are situated on the top and bottom jambs of your door, where they support its latch. The door latch slides into the strike plate, creating a seal when closed. If the strike plate is damaged, rusted, or not installed correctly, it can stop the latch from locking the door securely.

The most common reason for an outdoor door lock to become stuck or not close is a misalignment of the latch and strike plate. The easiest method to check for this is by performing the "lipstick test." Rub some lipstick on the outside of the deadbolt, then put masking tape on it. When you close the door, the lipstick will leave an impression on the tape that will show exactly where the latch meets the strike plate. If the mark is too low or high you can adjust the strike plate.

Sliding patio door locks help keep your home safe from intruders, and if they're not functioning correctly, you should repair the issue quickly. Follow these simple steps to repair your patio door lock and restore it's function.