Noonandejesus7073

Magnetic survey using multiple magnetometers to obtain gradiometric data can be used as a non-destructive method to search for buried firearms. We present magnetic dataset collected above a set of weapons buried at 0.6 m, 1.2 m, and 1.8 m depths. We provide three datafiles two datafiles were collected on a coarse grid (1 m by 0.5 m) before and after burial of the weapons, and a third one collected on a fine grid (0.25 m by 0.1 m) after the burial of the weapons which concentrates on the area of buried firearms. We used a Gem Systems GSM-19GW Overhauser gradiometer consisting of two sensors with a relative vertical separation of 55 cm. Data acquisition was done via non-automated point measurements within a gridded measurement domain with data collection locations managed using measurement tape. Each field campaign resulted in about 3,000 data points. In addition, we developed a set of MATLAB scripts to model the magnetic anomalies (total field and gradient) for buried firearms, this set is also included here. The data and modeling scripts relate to a research article published in Forensic Science International (Deng et al., Suitability of magnetometry to detect clandestine buried firearms from a controlled field site and numerical modeling [1]). The dataset may be helpful for testing new algorithms for weapons detection while the numerical codes can be modified and applied for simulating magnetic anomalies resulting from similar buried objects with potential application in the sub-disciplines of forensic and archaeological geophysics.This data article comprises collected data to verify a vibro-acoustic coupling model and raw records of optimized results on sectional geometries of two simplified sealing rubber models. The dataset is generated based on both analytical methods and numerical solutions, including Finite Element Simulation and Hybrid Finite Element - Statistic Energy Analysis Simulation. The calculations have been performed through a 2.3GHz PC with Intel Xeon Core E5-2658 v4 and 128 GB RAM in Tongji University. All the results from these data will help researchers and engineers in vibro-acoustic coupling analysis of dual-membrane or combined dual-membrane models with a sine-auxiliary function and advanced understanding of the coupling characteristics. One of the main original contributions is also to share the data sets to give the opportunity to researchers for testing and validating numerical models of the vibro-acoustic coupling problem. In addition, the optimization characteristics of sectional geometries of the sealing rubber models based on a modified simulated annealing algorithm can retain further potential analysis with the data provided. This Data in Brief article is an additional item directly alongside the following paper submitted in the Elsevier journal Applied Acoustics, "Optimal study on sectional geometry of rubber layers and cavities based on the vibro-acoustic coupling model with a sine-auxiliary function" [1], where the detailed interpretation of models and results can be found.This data article presents raw inferential statistical data which determine the use of consumer-generated content for online fashion apparel shopping among young adult consumers in South Africa. The data was gathered from consumers within the Gauteng Province metropolitan area of Johannesburg. Structural equation modelling approach using partial least squares statistical software (Smart PLS) was used to test the posited hypotheses in the conceptual research model. Structured questionnaires were distributed to consumers within the Johannesburg Metropolitan area. This data set show that perceived usefulness, perceived trustworthiness, knowledge and Competence has a major statistical impact on attitude towards the use of consumer generated content. The data also suggested a statistically significant relationship between attitude and intention to use consumer generated content as a source of information for online apparel shopping. In addition, the data showed that the perceived usefulness and trustworthiness had a statically marginal impact on usage intention. The data also shows that the perceived enjoyment of user generated content by users has had a negative and statically insignificant impact on attitude, while attitude has had a positive and significant effect on consumer behavioural intentions.Mycoplasma hominis is an opportunistic bacterium that can cause acute and chronic infections of the urogenital tract. selleck products This bacterium, like all other Mycoplasma species, is characterized by the reduced genome size, and, consequently, reduction of the main metabolic pathways. M. hominis cells cannot effectively use glucose as a carbon and energy source. Therefore, the main pathway of energy metabolism is the arginine dihydrolase pathway. However, several bacteria can use nucleosides as the sole energy source. Biochemical studies using Salmonella typhimurium have shown that three enzymes (thymidine phosphorylase, phosphopentose mutase and deoxyribose-phosphate aldolase) are involved in the thymidine catabolic pathway. All these enzymes are present in M. hominis. For understanding changes in the energy metabolism of M. hominis we performed shotgun proteome analysis of M. hominis cells in liquid medium with arginine or thymidine as a carbon source. LC-MS analysis was performed with an Ultimate 3000 Nano LC System (Thermo Fisher Scientific) coupled to a Q Exactive HF benchtop Orbitrap mass spectrometer (Thermo Fisher Scientific) via a nanoelectrospray source (Thermo Fisher Scientific). Data are available via ProteomeXchange with identifier PXD018714 (https//www.ebi.ac.uk/pride/archive/projects/PXD018714).This data article provides useful information often required for numerical modeling of the so-called microbond tests. It includes the experimental and simulation data of the microbond testing using Fibre Bragg Grating (FBG) fibres for optical strains. Microbond testing was performed on five different droplets of varying embedded length and diameter to collect the data. Finite element simulation was carried out and modelling was validated, by using two variables force and strain, to collect the data. The output data of the fitted models is given and is also visualized via graphs of force-strain derivative curves. The data of the simulations is provided for different finite element mesh densities. Here, to clarify the type and form of the data for the use by readers, the energy distribution curves describing various functionalities of the droplet, fibre and interface are presented. For further reading, the interpretation and analysis of this data can be found in a research article titled "3D interfacial debonding during microbond testing Advantages of local strain recording" (R.