Lemmingborre1771

How to Replace a Kia Sportage Replacement Key

For many Kia models keys, the key has the keyless entry system that is built into the key. This key usually resembles the remote control and can be replaced by a new one purchased from an Kia dealer or a locksmith.

Key fobs can stop working due to a variety of reasons, including batteries that are dead, worn buttons, water damage, signal interference and a damaged receiver module. Here are some suggestions on how you can get your Kia Sportage replacement key working again.

How do you replace the remote key or smart key





Whether your Kia is equipped with an intelligent key, remote key push-to-start keys, or a regular non-transponder steel key the battery in these keys will eventually need replacing. This is particularly relevant if your car displays a message indicating that the remote or smart key has a low battery.

Luckily, it's an easy procedure. To replace the key fob battery take the mechanical key from the slit at the back of the key fob. You then need to lift the cover. A small screw is inside the key fob, which holds the battery in place. With a small screwdriver, loosen the screw and remove the battery that was in place. Then, insert kia ceed key fob and close the slit inside the key fob.

When the key fob is equipped with a fresh battery check it by pressing the locks and unlock buttons. It's okay in case the doors lock and unlock as you expect. You can now utilize the hands-free feature to lock and unlock your Kia whenever your fingers feel chilly or when you need to do some errands in Brandon.

Note: Some key fobs might need to be programmed (transponder chips or smart keys). This requires a machine for programming, which is only available to the automotive locksmith or dealer. Other keys (non transponder metal keys), do not need programming. If you're required to reprogramme your key, you'll need to write down the key code's number on the key code tag.

How to replace a battery

If the Kia key fob doesn't respond to pressing the lock/unlock button, it's likely that the battery is not fully charged. A low battery may also cause other issues like the check engine light turning on or a delay in cranking the engine. Fortunately, replacing the battery on the key fob is a simple DIY project that requires just some basic tools.

Make sure to shut off your vehicle and shut the doors before you begin. Find the small, metal or plastic piece on the bottom of your key fob, and play with it until a metallic key slips out. You can then insert the key in the handle of the door for the driver to unlock your car.

To replace the battery in the key fob, you must remove the cover on the rear. Utilize a plastic plier tool to loosen the latch that holds the black negative cable. Remove the old battery, and then align the replacement battery so that its "+" side faces you, and the "-" negative side is facing the fob's electrical contacts. Push the new CR2032 battery straight into position with care to avoid using too much force to avoid bending or damaging the contacts of the metal.

Once the new battery has been installed and the key fob is turned on, turn it off and then turn it on in the ignition repeatedly until the door locks cycle. Then, test your Kia key fob to check whether it's functioning properly again.

How can you replace the smart key?

Depending on the model of the Kia Sportage, you may have an ordinary key fob or a smart key. The smart key is equipped with an embedded mechanical key blade while the standard keyfob does not. Both kinds of key fobs come with batteries inside which eventually needs to be replaced. This is a straightforward process which takes just two minutes.

Make sure you turn off your Kia and stand on a flat well-lit and well-lit area before you begin. Keep in mind that the fob can contain small pieces that could be thrown off if you're not careful.

The small release button is located on the lower backside. It will be either an oval silver button or a rectangular slot. Once you press this button, the mechanical blade will be released and you can then open the key fob.

Once you have the key fob open it is easy to take off the old battery and replace it. The new battery is a the CR-2032, and it can be bought on the internet or at your local auto parts store. After you've finished, your key fob should allow you to lock or unlock and start your vehicle, even if it isn't running.

How do I replace a mechanical key

The Kia key fob is an amazing option that lets us lock and unlock our vehicle with the click of the button. Like all devices it is possible that the Kia key fob can occasionally have problems. There are steps to take to solve these issues and keep our key fobs in good condition for the long term.

One of the most frequent problems is a dead or dead battery. This could cause your device to stop working or operate intermittently. If this is the problem it is time to replace the battery an entirely new battery.

If this doesn't fix the issue you can try using a standard flathead screwdriver to wedge open the fob's plastic casing. Be sure not to damage any internal components or scratch the plastic. Once the battery is removed, replace it with a new one.

When the new battery is installed, close and unlock the doors using the mechanical key (every kia fob has an emergency mechanical key that can fit in the slot). Test the key fob to verify that it's working correctly. If the fob isn't working, contact a locksmith or dealer to help solve the problem. To avoid future lockouts, make sure you get an emergency key that will be able to work with all door and trunk cylinders.