Korsholmbarton5485

Double Glazing Door Lock Repairs

Are your uPVC window or door mechanism broken? Perhaps the window or door handles don't meet up properly or are hard to use.

double glazing repairs near me is crucial that the double glazed doors work smoothly, otherwise you'll be wasting energy and increase the likelihood of burglary. Owen the Locksmith can repair your door lock at an affordable cost.

Snapped Key

It can be frustrating when a key is snapped inside a lock. It could also be a security risk, as the door might not lock and leave you open to intrusion. There are a few quick fixes you can make to resolve the issue and get your door working again.

Keep calm. If you panic you could end up pushing the broken key further into the lock.

Next spray WD-40 or a different penetrating oil into the lock to make the broken piece slip out more easily. You can also use the screwdriver to break any pieces that are stuck. If you're lucky enough to have a small piece of the key that is hanging out and you want to remove it, make use of a paperclip, or any other metal object that is thin to grab it and pull it out. Both of these methods work well, however, be careful not to push the broken piece of the key further into the keyway.

Some paperclips have grooved edges that can work in a pinch as hook extractors and some Jigsaw blades can also be used for this function. If you don't happen to have any of these items then you can bend a hook using needle-nosed pliers. You can also use a pair of tweezers grasp and pull out the last bit of the broken keys.

If you cannot remove the broken piece of key then you can use a lock deicer. It's available at most hardware stores and works by freezing any moisture present inside the lock.

If none of these solutions work, it may be time to call a locksmith. The experts at Fitlocks can quickly fix problems such as broken handles and snapped keys using uPVC locks and door mechanisms. They can also alter the double glazing door mechanisms so that they are simpler to use. Get a double glazing repair via our website, or give us a call to discuss your requirements.

Broken Cylinder

A damaged cylinder poses an extremely risky security issue. A professional locksmith is able to fix the cylinder. To fix the cylinder, locksmiths will need to tap it. This can be done using a hammer or other tool. However, the best method is to make use of a wire or a long match. Then, position the end of the match or wire close to the keyway. The locksmith can strike the lock to crack it open. This is much safer than using a hammer, which could cause damage to the lock.

The most common cause of cracks in the cylinder head is overheating. This can occur when the cylinder block as well as the cylinder head are made of various metals, such as cast iron and aluminium. Different metals will heat up and cool off at different rates. This could cause localized hotspots to expand faster than the rest of the cylinder.

Another possible cause for cracks in the cylinder is corrosion. If the cylinder head as well as the cylinder block aren't maintained properly, this could cause corrosion or rust, which may cause them to expand at more than they should. Over time, this can also lead to cracks.





If your uPVC window or door lock is rigid and requires a lot more pressure to turn it could be due to a variety of causes. This issue could be caused by a faulty locking mechanism or misalignment, and also a worn out handle.

It is a quick and cost-effective fix that a majority of homeowners with double glazing can perform. A professional locksmith will typically be able solve this problem within an hour of arriving at your property. They can repair the locking mechanisms, or change the window handles and replace the gearboxes, based on your specific needs. A skilled locksmith will always be able to advise you of the most cost-effective solution for your home. They can also suggest upgrades to the highest-security 3 Star Euro cylinders, TS007, that will give you an additional layer of protection against burglars. It's a small price to enjoy the peace of mind that comes from knowing that your uPVC door is secured.

Broken Handle

It's not a surprise that window handle locks can break. They have intricate mechanisms that become less effective over time. It isn't easy to determine the reason for a broken window handle lock and repair it correctly.

Whether the problem is in the internal locking mechanism or the latch, fixing your broken handle will increase your uPVC double glazing door's security as well as help you to stop draughts. Incorrectly repairing or replacing your handle can be very expensive and could harm the door's frame as well as lock, so it's worth taking the time to do it right.

With the window open and the window open, loosen the screw holding the handle using the screwdriver. The screw should be located on the inside of the backplate. It is typically covered by an eye-catching cap to conceal it for aesthetic purposes. It is not recommended to lose any internal components of the handle like the levers and plates on either side. Ideally, keep them in the same place so you can re-install them in the event of a need.

Then, with an additional screwdriver take the screw off that connects the handle with the spindle in the back. Once this is released, you'll be in a position to pull the handle off and take out the broken spindle. Replace this with a new one, making sure that it's the same length as the previous one (you can typically find these on the internet or in hardware stores) and securely screw it in place. Be careful not to tighten too much as this could cause damage to the handle or the window frame.

Close the handle and try it. It should operate smoothly and you'll be able to open your windows once again.

Be sure to double-check that your uPVC window is shut properly when you're working with the handle. If they aren't closing properly, you could experience damp or draughts inside your home. You could also compromise the energy efficiency of your home. A local window company, like Core Sash Windows, will be in a position to adjust the hinges on your window frames so they can shut properly.

Broken Spindle

It is usually the case that the spindle inside the handle is broken, not the handle itself. This is most typical in uPVC tilt and turn windows. These kinds of windows require a handle which is a lock mechanism that is located in the frame of the window. The handle is attached to a central rod that activates a series of locks that are shaped like mushrooms and secure into the frame of the window keep. If the dead latch mechanism is not able to open after the handle is turned, it is most likely the spindle has been damaged. This could be a frustrating issue.

There are solutions to this problem. A skilled locksmith can quickly and efficiently solve the issue. They can take apart the window handle using a tool that removes the wheel part of the mechanism, where the spindle goes. This can be done without damage to the handle or the window frame.

Once the wheel has been removed, the technician can inspect the spindle and determine what has caused it to break. This involves breaking down the spindle into its individual components and carefully observing their general condition as well as any particular areas of damage or excessive wear. This process is usually carried out by technicians working in a clean and safe environment.

Then, clean the damaged spindle. This will help remove any debris or dirt that may be obstructing it from working normally. The spindle could be replaced or repaired. If it is being replaced the technician could use a dowel of a similar size to the original and drill mating holes into both parts of the spindle. This will ensure that the spindle fits perfectly with the handle.

If the damaged spindle cannot be repaired it may need to be replaced entirely. Home centers sell generic replacements however if your window design is unique then you'll have to speak with a cabinet maker or woodworker who can replicate the exact component. Once the new spindle is installed, it can be attached to the handle by line up the holes for screws in the handle with the frame's existing screws. Once the new handle is firmly in place, you'll be able to operate your uPVC window.