Hollowayohlsen2512

Results of this study suggest that different significant correlations were observed between the skin and tooth color for different L*, a*, and b parameters (p <0.05 and p <0.01). The results indicated that skin color can be used for tooth color selection in case of loss of natural teeth or when discoloration is present on existing teeth.

Results of this study suggest that different significant correlations were observed between the skin and tooth color for different L*, a*, and b parameters (p less then 0.05 and p less then 0.01). The results indicated that skin color can be used for tooth color selection in case of loss of natural teeth or when discoloration is present on existing teeth.

The boron and fluoride mainly accumulate in the bones and teeth of the human body. The purpose of this study is to determine boron or fluoride levels in the whole tooth, to evaluate the correlation between their levels and to compare these levels in primary/permanent, carious, and non-carious groups.

The boron and fluoride levels of thirty-six teeth, separated such as primary carious (n=9) and non-carious (n=9), permanent carious (n=9) and non-carious (n=9), were determined by ICP-MS and ion-selective electrode, respectively.

While boron levels were between 0.001 and 5.88 ppm, the fluoride levels were between 21.24 and 449.22 ppm. The boron level of non-carious teeth was higher than those of carious teeth in primary and permanent tooth groups. However, this difference was not statistically significant (p>0.05). The fluoride level of non-carious teeth was higher than those of carious teeth in primary (p=0.062) and permanent teeth groups (p=0.046). Negative correlation, found between boron and fluoride in all groups, was significant only in non-carious teeth group (r=-0.488, p=0.040).

The results of our study proved the importance of fluoride as a protective factor for dental caries once more. The boron levels in non-carious teeth were also higher than carious teeth. However, it was not significant. Moreover, there was negative correlation between teeth boron and fluoride levels. Therefore, it is necessary to conduct more detailed studies on the tooth boron level and its relation with caries formation and with fluoride levels.

The results of our study proved the importance of fluoride as a protective factor for dental caries once more. The boron levels in non-carious teeth were also higher than carious teeth. However, it was not significant. Moreover, there was negative correlation between teeth boron and fluoride levels. Therefore, it is necessary to conduct more detailed studies on the tooth boron level and its relation with caries formation and with fluoride levels.

This study aimed to evaluate if the contact of calcium hydroxide cements with polyacrylic and phosphoric acids would alter selected microscopic and physical and chemical properties.

Chemically activated (Hydro C and Dycal Advanced Formula II) and resin-modified photoactivated (Ultra-blend Plus) calcium hydroxide cements were examined after exposure to the following different strategies contact with no substance (control group); rinsing with water and drying; contact with polyacrylic acid, rinsing with water, and drying; and contact with phosphoric acid, rinsing with water, and drying. Surface morphology, determined by scanning electron microscopy (SEM), water sorption and solubility, and the release of hydroxyl ions were evaluated.

SEM showed a greater impact of the conditioning acids on the surface of the chemically activated cements. Ultra-blend Plus obtained the highest value of sorption (516.8 μg/mm3) and solubility (381.1 μg/mm3) and Hydro C had the lowest values 251.9 μg/mm3 and 206.3 μg/mm3 respectively. Considering the release of hydroxyl ions in comparison with time, Hydro C and Ultra-blend Plus presented significant statistical difference for polyacrylic and phosphoric acid subgroups.

Hydro C and Dycal presented intensification of surface irregularities after contact with conditioning acids. The chemically activated materials suffered a decrease in sorption and solubility. The action of the conditioning acids promotes greater increase of the release of hydroxyl ions for Hydro C and Dycal.

Hydro C and Dycal presented intensification of surface irregularities after contact with conditioning acids. The chemically activated materials suffered a decrease in sorption and solubility. The action of the conditioning acids promotes greater increase of the release of hydroxyl ions for Hydro C and Dycal.

To evaluate the effects of surface coating and one-year water storage on the flexural strength of fluoride-releasing restorative materials.

Forty specimens were prepared from each material; GCP Glass Fill (GCP), Amalgomer CR (AHL), Zirconomer (Shofu), Fuji IX GP Capsule (GC), Beautifil II (Shofu), Estelite Σ Quick (Tokuyama) and reliaFIL LC (AHL). The specimens were randomly divided into two groups; surface coated with G-Coat Plus (GC) and uncoated. Each group was subdivided into two groups stored in distilled water at 37◦C for 24 h and 1 year before testing (n=10). The flexural strength was evaluated using three-point bending test according to the ISO 40492009 standard using a universal testing machine. see more After flexural strength test, a cross-section of the coated specimens was evaluated with scanning electron microscopy (SEM).

A significant increase was observed on the flexural strength of Amalgomer CR, Zirconomer and Fuji IX GP after 24 h when G-Coat Plus was applied (p<0.05). This significant increase was observed on the flexural strength of only Amalgomer CR and Zirconomer after 1 year (p<0.05). The highest flexural strength was obtained with Beautifil II, Estelite Σ Quick and reliaFIL LC after 24 h and 1 year (p<0.05). After 1 year, there was decrease on the flexural strength of the other materials except Beautifil II, Estelite Σ Quick and reliaFIL LC.

The resin coating improved the flexural strength of some glass ionomer-based materials but the water aging decreased the same physical properties.

The resin coating improved the flexural strength of some glass ionomer-based materials but the water aging decreased the same physical properties.