Gambleguerrero7933

Single point diamond turning (SPDT) is highly versatile in fabricating axially symmetric form, non-axially-symmetric form and free form surfaces. However, inevitable microstructure known as turning marks left on the surface have limited the mirror's optical performance. Based on chemical mechanical polishing (CMP) mechanism, smoothing polishing (SP) process is believed to be an effective method to remove turning marks. However, the removal efficiency is relatively low. In this paper, based on Greenwood-Williamson (GW) theory, the factors that limit removal efficiency of SP are discussed in details. Influences of process parameters (work pressure and rotational speed) are firstly discussed. With further analysis, surface spectral characteristics are identified as the inherent factor affecting further efficiency improvement. According to theoretical analysis, the removal efficiency of isotropic surface is nearly 1.8 times higher than anisotropy surface like surface with turning marks. A high efficiency turning marks removal process combining ion beam sputtering (IBS) and SP is proposed in our research. With removal depth exceeding 100 nm, the isotropic aluminum surface can be constructed by IBS so that the efficiency of SP process can be greatly improved. Though deteriorated by IBS, the surface roughness will be rapidly reduced by SP process. Finally, experiments are conducted to verify our analysis. A 3.7 nm roughness surface without turning marks is achieved by new method while direct SP can only reach roughness of 4.3 nm with evident turning marks. Experimental results show that removal efficiency nearly doubled which matches well with the theoretical analysis. A-64077 Our research not only can be used as a high efficiency turning marks removal and surface quality improvement method but also can be a new method for high precision aluminum optics fabrication.In this paper, a phase-sensitive amplifier (PSA)-based two dimensional (2D)-to-one dimensional (1D) constellation reforming system is proposed and analyzed in detail. The proposed system theoretically realizes seven kinds of 10 GBaud quadrature amplitude modulation (QAM)-to-pulse amplitude modulation (PAM) conversions, including quadrature phase shift keying-to-PAM4 and 8QAM-to-PAM8 conversions. The constellation reforming system consists of a constellation squeezing PSA and a multi-level vector moving PSA. The operating principle and formula derivations of constellation squeezing and vector moving processes are fully explained, including the PSA transfer characteristics and PSA gain axis angle analytical solutions. When implementing QAM-to-PAM conversions, the constellations, spectra, eye diagrams, error vector magnitudes and bit error ratio (BER) performances of the QAM and PAM signals are measured. For 8QAM-to-PAM8 conversion, with the input OSNR of 25 dB and 30 dB, at the BER of 10-3, the converted PAM8 shows the receiver OSNR of 38.9 dB and 35.2 dB, respectively. The proposed and verified 2D-to-1D constellation reforming system builds an optical bridge connecting long-haul and short-reach networks, which can be employed in the format conversion, high-order format signal generation and shaping, and flexible information aggregation/de-aggregation.The mold core fabrication of a freeform surface on die steel by ultra-precision machining can make the optical elements of freeform be mass-produced by plastic injection and glass mold pressing. However, because steel is a typical difficult-to-cut material, the technical limitations of existing machining methods hardly meet the current requirements of design. In this paper, a novel machining method, one-dimension ultrasonic-assisted slow tool servo (UASTS) turning, is proposed to manufacture the freeform surface with high-precision and large-steepness on the die steel. Aiming at the characteristics of UASTS turning, the tool trajectory is generated by analyzing the compensation of tool radius and confirming the position of ultrasonic displacement. The 2D surface model contours of residual tool marks are established for predicting the 3D surface topography based on considering the effects of kinematics, material elastic recovery and plastic side flow. In the experiments, the large-amplitude bidirectional sinusoidal wave grid (BSWG) surface is successfully fabricated by UASTS technology on the material, Polmax steel, for which the value Rt of surface roughness is less than 70nm and the value Ra of surface roughness can achieve to 3.298nm. The results show that the freeform surface with high-precision and large-steepness can be machined by UASTS turning technology on mold steel.We present an ultrasensitive enhanced fabrication-tolerance refractometer utilizing the polarimetric interference of a tapered PANDA-air-hole fiber (PAHF). To obtain high birefringence and unique group birefringence, the PAHF is specially designed by introducing double air holes into the cladding. Ultrahigh sensitivity can be achieved by reducing the group birefringence difference to zero, defined as birefringent dispersion turning point (BDTP). By modifying the diameter of PAHF, the birefringent dispersion can be effectively manipulated to reduce the group birefringence difference. In this way, the workable diameter range for realizing the ultrahigh sensitivity is twice as large as that of conventional microfibers. Additionally, the ultrasensitive wavelength band is dramatically expanded by at least 600 nm, enabling a compact structure and a flexible fiber-length design. Due to the tunable dispersion optimization, the distinctive properties of ultrahigh sensitivity, enhanced fabrication tolerance, and broadband operation can be achieved. We experimentally verified the ultrahigh refractive index sensitivity of 47223 nm/RIU around the BDTP, and the experimental results matched well with the simulations.Yellow Luminescence (YL) band and blue luminescence (BL) band in a studied unintentionally doped GaN sample show a transient behaviour where the observed luminescence intensities change with the exposure time of the sample under 325 nm laser beam excitation at 10-300 K. Such an intensity variation is accompanied with a red-shift for YL peak at 10-140 K and one for BL peak at 140 K. We propose that such behaviours are related to the chemical transformations of YL-related CN and CNON defects, and BL-related CN-Hi and CNON-Hi defects during the exposure.