Fowlercooley2984
Furthermore, the results indicate that the model-based learned iterative reconstruction method outperforms all other learning-based post-processing methods in terms of generalizability and robustness.We present an experimental comparison of photoacoustic responsivities of common highly absorbing carbon-based materials. The comparison was carried out with parameters relevant for photoacoustic power detectors and Fourier-transform infrared (FTIR) spectroscopy we covered a broad wavelength range from the visible red to far infrared (633 nm to 25 μm) and the regime of low acoustic frequencies ( less then 1 kHz). The investigated materials include a candle soot-based coating, a black paint coating and two different carbon nanotube coatings. Of these, the low-cost soot absorber produced clearly the highest photoacoustic response over the entire measurement range.The photoacoustic measurement technique is a powerful yet underrepresented method to characterize the thermal transport properties of thin films. For the case of isotropic low thermal diffusivity samples, such as glasses or polymers, we demonstrate a general approach to extract the thermal conductivity with a high degree of significance. We discuss in particular the influence of thermal effusivity, thermal diffusivity, and sample layer thickness on the significance and accuracy of this measurement technique. These fundamental thermal properties guide sample and substrate selection to allow for a feasible thermal transport characterization. Furthermore, our data evaluation allows us to directly extract the thermal conductivity from this transient technique, without separate determination of the volumetric heat capacity, when appropriate boundary conditions are fulfilled. Using silica, poly(methyl methacrylate) (PMMA) thin films, and various substrates (quartz, steel, and silicon), we verify the quantitative correctness of our analytical approach.Klein-Levin Syndrome (KLS) is an extremely rare neurological disorder which can manifest as recurring spells of sleepiness, cognitive disturbances and behavioral changes. We present a novel case of KLS relapse in the setting of Coronavirus disease-19 (COVID-19). A 36-year-old male who had a known history of KLS since adolescence was admitted with sleepiness and behavioral disturbances. Brain imaging and autoimmune encephalitis work was unremarkable. The patient was diagnosed with a relapse of KLS secondary to COVID-19 based on symptomology and lack of any other precipitating factor. The patient required 8 days of hospitalization and was treated with benzodiazepines due to a history of robust response to lorazepam during a prior episode. The patient progressively improved and was discharged home on lorazepam taper. We report that similar to other neurotropic viruses, severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) could be the culprit in instigating KLS relapse.Due to the coronavirus disease 2019 pandemic, the number of coronavirus disease 2019-associated acute respiratory distress syndrome is rapidly increasing. The heterogeneity of coronavirus disease 2019-associated acute respiratory distress syndrome contributes to the complexity of managing patients. Here we described two patients with coronavirus disease 2019-associated acute respiratory distress syndrome showing that the bedside physiological approach including careful evaluation of respiratory system mechanics and visualization of ventilation with electrical impedance tomography was useful to individualize ventilatory management.The most effective ways to mitigate the diffusion of the COVID-19 pandemic are social distancing and the use of face masks as barrier to avoid droplets and to filtrate exhalations coming from infected subjects. Currently used face masks are products developed to be used by workers, both in health care and other contexts, where their use is limited in time and the disposal scenario is properly managed. Their use in a pandemic situation can be thus considered a remedial action due to the emergency. New masks or mask families are needed based on the desirable requirements retrieved by the analysis of the current worldwide situation and covering the gap observed in the market. The present paper aims to describe the complete product development process of a new facial mask (or mask family) for a daily use on a pandemic situation. It challenges the time constraint of the COVID-19 pandemic by adopting a four-step approach and concurrent development of the first phases (definition of requirements and functional derivation). The engineering design process allows to derive two different solutions able to fulfil all the requirements (demands and wishes) of final users, by assuring high ergonomic performance, as well as environmental, economic, and social sustainability.
Bone-anchored maxillary protraction (BAMP) is an emerging treatment option for orthopedic correction of maxillary deficiency in young patients. Compared to reverse pull headgear (RPHG), it is believed that forces generated during BAMP result in greater circum-maxillary sutural separation, mandibular retrusion, and improved maxillary protraction. Mechanical loading of the circum-maxillary sutures during BAMP is still poorly understood.
20 ex-vivo pig heads were used. Miniplates and molar tubes were installed like clinical procedures. A series of five 200g-force (gf) elastics were applied on the right and left side until 1000gf were reached. Strain gauges were installed across the zygomatico-maxillary (ZMS), zygomatico-temporal (ZTS), and nasofrontal suture (NFS). Differential variable reluctance transducers (DVRTs) were installed across the ZTS. Deformation of the sutures during BAMP and RPHG was measured and compared.
Higher average sutural deformation of the ZTS and ZMS was seen in BAMP than RPHG 36.6±20.6με vs 18.0±12.4με and 54.7±28.5με vs 12.5±14.8με, respectively. Similarly, higher NFS deformation was seen in BAMP (18.4±12.9με vs. -0.8±12.0με). DVRT data showed higher ZTS separation in BAMP than RPHG (6.3±5.2μm vs. 1.7±2.1μm). These differences were all statistically significant using the Wilcoxon-signed rank test.
Both RPHG and BAMP forces separate the ZTS and ZMS. BAMP resulted in higher levels of sutural separation at the ZTS and ZMS by 2- and 5-fold, respectively.
Both RPHG and BAMP forces separate the ZTS and ZMS. selleck BAMP resulted in higher levels of sutural separation at the ZTS and ZMS by 2- and 5-fold, respectively.
