Dickeysejersen8435

Cells in such an islet were segmented and visualized in 3D. Further, morphological alterations of tumorous tissue of the pancreas were characterized. To this end, the anisotropy parameter Ω, based on intensity gradients, was used in order to quantify the presence of collagen fibers within the entire biopsy specimen. This proof-of-concept experiment of the multiscale approach on human pancreatic tissue paves the way for future 3D virtual pathology.The design and construction of an instrument for full-field imaging of the X-ray fluorescence emitted by a fully illuminated sample are presented. The aim is to produce an X-ray microscope with a few micrometers spatial resolution, which does not need to scan the sample. Since the fluorescence from a spatially inhomogeneous sample may contain many fluorescence lines, the optic which will provide the magnification of the emissions must be achromatic, i.e. its optical properties must be energy-independent. The only optics which fulfill this requirement in the X-ray regime are mirrors and pinholes. The throughput of a simple pinhole is very low, so the concept of coded apertures is an attractive extension which improves the throughput by having many pinholes, and retains the achromatic property. Modified uniformly redundant arrays (MURAs) with 10 µm openings and 50% open area have been fabricated using gold in a lithographic technique, fabricated on a 1 µm-thick silicon nitride membrane. The gold is 25 µm thick, offering good contrast up to 20 keV. The silicon nitride is transparent down into the soft X-ray region. MURAs with various orders, from 19 up to 73, as well as their respective negative (a mask where open and closed positions are inversed compared with the original mask), have been made. Having both signs of mask will reduce near-field artifacts and make it possible to correct for any lack of contrast.Full-field X-ray nanotomography based on a Fresnel zone plate offers a promising and intuitive approach to acquire high-quality phase-contrast images with a spatial resolution of tens of nanometres, and is applicable to both synchrotron radiation and laboratory sources. However, its small field of view (FOV) of tens of micrometres provides limited volume information, which primarily limits its application fields. This work proposes a method for expanding the FOV as the diameter of the objective zone plate, which provides a 400 µm FOV at below 500 nm resolution with Zernike phase contrast. find more General applications of large-volume nanotomography are demonstrated in integrated circuit microchips and Artemia cysts. This method can be useful for imaging/analyzing industrial and biological samples where bulk properties are important or the sample is difficult to section.Ptychography is a scanning coherent diffraction imaging technique which provides high resolution imaging and complete spatial information of the complex electric field probe and sample transmission function. Its ability to accurately determine the illumination probe has led to its use at modern synchrotrons and free-electron lasers as a wavefront-sensing technique for optics alignment, monitoring and correction. Recent developments in the ptychography reconstruction process now incorporate a modal decomposition of the illuminating probe and relax the restriction of using sources with high spatial coherence. In this article a practical implementation of hard X-ray ptychography from a partially coherent X-ray source with a large number of modes is demonstrated experimentally. A strongly diffracting Siemens star test sample is imaged using the focused beam produced by either a Fresnel zone plate or beryllium compound refractive lens. The recovered probe from each optic is back propagated in order to plot the beam caustic and determine the precise focal size and position. The power distribution of the reconstructed probe modes also allows the quantification of the beams coherence and is compared with the values predicted by a Gaussian-Schell model and the optics exit intensity.An X-ray transparent experimental triaxial rock deformation apparatus, here named `Mjölnir', enables investigations of brittle-style rock deformation and failure, as well as coupled thermal, chemical and mechanical processes relevant to a range of Earth subsurface environments. Designed to operate with cylindrical samples up to 3.2 mm outside-diameter and up to 10 mm length, Mjölnir can attain up to 50 MPa confining pressure and in excess of 600 MPa axial load. The addition of heaters extends the experimental range to temperatures up to 140°C. Deployment of Mjolnir on synchrotron beamlines indicates that full 3D datasets may be acquired in a few seconds to a few minutes, meaning full 4D investigations of deformation processes can be undertaken. Mjölnir is constructed from readily available materials and components and complete technical drawings are included in the supporting information.When performing transmission polychromatic beam topography, the extensions to the line segments of the diffraction images of a straight dislocation are shown to intersect at a single point on the X-ray film. The location of this point, together with the diffraction pattern recorded on the film by synchrotron radiation, gives the crystallographic direction [hkl] of the dislocation unambiguously. The results of two synchrotron topography experiments are presented. Very long dislocations found in the center of a large 450 mm-diameter Czochralski silicon crystal align with the growth direction [001]. In the other silicon sample, the dislocations are of mixed type and along the [011] direction.X-ray synchrotron sources, possessing high power density, nanometric spot size and short pulse duration, are extending their application frontiers up to the exploration of direct matter modification. In this field, the use of atomistic and continuum models is now becoming fundamental in the simulation of the photoinduced excitation states and eventually in the phase transition triggered by intense X-rays. In this work, the X-ray heating phenomenon is studied by coupling the Monte Carlo method (MC) with the Fourier heat equation, to first calculate the distribution of the energy absorbed by the systems and finally to predict the heating distribution and evolution. The results of the proposed model are also compared with those obtained removing the explicit definition of the energy distribution, as calculated by the MC. A good approximation of experimental thermal measurements produced irradiating a millimetric glass bead is found for both of the proposed models. A further step towards more complex systems is carried out, including in the models the different time patterns of the source, as determined by the filling modes of the synchrotron storage ring.