Carstensrhodes7229

Determining the blood glucose level is important for the prevention and treatment of diabetes mellitus. We developed a sensor system using Quartz Crystal Microbalance (QCM) to determine the blood glucose level from human blood serum. This study consists of two experimental stages artificial glucose/pure water solution tests and human blood serum tests. In the first stage of the study, the QCM sensor with the highest performance was identified using artificial glucose solution concentrations. In the second stage of the study, human blood serum measurements were performed using QCM to determine blood glucose levels. QCM sensors were coated with phthalocyanines (Pcs) by jet spray method. The blood glucose values of 96 volunteers, which ranged from 71 mg/dL to 329 mg/dL, were recorded. As a result of the study, human glucose values were determined with an average error of 3.25%.In this study, the catalytic activity and stability of flowerlike hybrid horseradish peroxidase (HRP) nanobiocatalyst (HRP-Cu 2+ ) obtained from Cu 2+ ions and HRP enzyme in the polymerization reaction of guaiacol were analyzed. We demonstrated that HRP-Cu 2+ and hydrogen peroxide (H 2 O 2 ) initiator showed significantly increased catalytic activity and stability on the polymerization of guaiacol compared to that of free HRP enzyme. Poly(guaiacol) was observed with quite high yields (88%) and molecular weights (38,000 g/mol) under pH 7.4 phosphate-buffered saline (PBS) conditions at 60 °C with 5 weight% of HRP-Cu 2+ loading. HRP-Cu 2+ also shows very high thermal stability and works even at 70 °C reaction temperature; free HRP enzyme denatures at that temperature. Furthermore, HRP-Cu 2+ provided considerable repeated use and showed some degree of catalytic activity, even after the fourth recycle, in the polymerization of guaiacol.A series of cholesterol and based hydrophobic urea and thiourea compounds were synthesized and successfully used as a cocatalyst for L-proline catalyzed aldol reactions in the presence of water. The anticonfigured products were obtained with good yields (up to 94%), high diastereoselectivities (up to 955), and high enantiomeric excesses (up to 93% ee ). The successful results for catalytic efficiency of L-proline in the presence of water reveal the importance of the hydrophobic nature of cholesterol and diosgenin parts of thiourea on the reactivity and selectivity in the presence of water.In this research, molecular imprinting polymers (MIPs) for D-arabinitol were synthesized using a bulk polymerization method through a noncovalent approach. The MIPs were prepared by using D-arabinitol as a template, acrylamide as a functional monomer, ethylene glycol dimethacrylateas cross-linker, benzoyl peroxide as an initiator and dimethyl sulfoxideas a porogen. MIPS was synthesized in several formulas with a different molar ratio of template to functional monomers and cross-linker. selleck chemicals llc Fourier-transform infrared spectroscopy (FT-IR) and scanning electron microscopy (SEM) were used to characterize the MIPs produced. A batch rebinding assay was used to test the binding efficiency of each formula. Batch rebinding test results revealed that MIPsF3 with a molar ratio of the template monomer and crosslinker ratio respectively (1 4 25) had the highest binding capacity at 1.56 mgg -1 . The results of isotherm adsorption showed that the MIPs produced followed the Freundlich equation with an R-value of 0.97. The MIPs produced was also selective toward its isomeric compounds (i.e. L-arabinitol, adonitol, xylitol, and glucose). The extraction efficiency of the MIPs against D-arabinitol was 88.98%.Phenyl-4,4-di(3,6-dibutoxyphthalonitrile) ( 3 ) was synthesized by the reaction of 1,4-phenylenebisboronic acid ( 1 ) and 4-bromo-3,6-dibutoxyphthalonitrile ( 2 ), using Suzuki cross-coupling reaction. The newly synthesized compound ( 3 ) was characterized by FT-IR, MALDI-MS, ESI-MS, 1 H-NMR, 13 C-NMR, and 13 C-DEPT-135-NMR. The fluorescence property of phenyl-4,4-di(3,6-dibutoxyphthalonitrile) ( 3 ) towards various metal ions was investigated by fluorescence spectroscopy, and it was observed thatthe compound ( 3 ) displayed a significantly 'turn-off' response to Fe 3+ , which was referred to 12 complex formation between ligand ( 3 ) and Fe 3+ . The compound was also studied via density functional theory calculations revealing the interaction mechanism of the molecule with Fe 3+ ions.Turkey is the leading country in the world in terms of boron production and sale. Increasing boron production goes along with an increasing generation of boron wastes. The pollution of the soil and the air around the waste piles, as well as the occupation of several square kilometers of ground, are major environmental problems. It is, therefore, very important to make use of the wastes to both protect the environment and create revenue. This work presenteda road map for fast screening of boron waste for critical elements followed by determination of the elements using small footprint low power instrumentation. The sample preparation was kept to a minimum. A procedure that allowed an assessment of critical materials in industrial production waste with minimal consumption of hazardous acids, energy, and time was presented. The samples were first screened for valuable and hazardous elements by micro-X-ray fluorescence (XRF). Samples with considerable contents of Cs, Rb, and Aswere then prepared as slurries for the total reflection XRF (TXRF) measurement. To evaluate the TXRF procedure, a standard reference material was analyzed. As a result, Rb and Cs in concentrations up to 420 ± 70 and 1500 ± 200 mg/kg were detected in some of the waste forms. The time savings were in order of a factor of 3 when comparing the prescreening combined micro-XRF and TXRF approach to an all TXRFanalysis approach.Water management is one of the obstacles in the development and commercialization of proton exchange membrane fuel cells (PEMFCs). Sufficient humidification of the membrane directly affects the PEM fuel cell performance. Therefore, 2 different hydrophobic polymers, polydimethylsiloxane (PDMS) and (3-Aminopropyl) triethoxysilane (APTES), were tested at different percentages (5, 10, and 20 wt.%) in the catalyst layer. The solution was loaded onto the surface of a 25 BC gas diffusion layer (GDL) via the spraying method. The performance of the obtained fuel cells was compared with the performance of the commercial catalyst. Characterizations of each surface, including different amounts of PDMS and APTES, were performed via scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDX) analyses. Molecular bond characterization was examined via Fourier transform infrared spectroscopy (FTIR) analysis and surface hydrophobicity was measured via contact angle measurements. The performance of the fuel cells was evaluated at the PEM fuel cell test station and the 2 hydrophobic polymers were compared.