Blumhjorth9606

The dynamic voltage is a unique phenomenon of superconducting materials. It arises when the superconductor is carrying a DC transport current and spontaneously in subject to an AC magnetic field. This study excavates the aspects that previous studies have not comprehensively investigated the dynamic voltage in a DC-carrying superconducting tape exposed to different oscillating AC magnetic fields. First, the fundamental physics of dynamic voltage/flux of superconductors is reviewed and further analysed in detail. We used the superconducting modelling method using the H-formulation merged into the finite-element method (FEM) software, to re-produce the typical dynamic voltage behaviour of a superconducting tape. The modelling was verified by both the analytical and experimental results, in order to precisely prove the reliability of the modelling. Afterwards, the modelling was performed for a DC-carrying superconducting tape under four different oscillating magnetic fields (sine, triangle, sawtooth and square), and their corresponding dynamic voltages and energy losses were analysed and compared. Results show the sinusoidal magnetic field can lead to the optimal combination of reasonable dynamic voltage but relatively lower loss, which is suitable for those superconducting applications requiring dynamic voltage as the energy source, e.g., flux pumps. This article presents novel investigation and analysis of the dynamic voltage in superconducting materials, and both the methodology and results can provide useful information for the future design/analysis of superconducting applications with DC transport currents and AC magnetic fields.The present study aimed to compare the action of advanced platelet-rich fibrin (A-PRF+) alone with the action of A-PRF+ combined with autologous gingival fibroblasts. The components released from A-PRF+ conditioned with autogenous fibroblasts that were quantified in the study were fibroblast growth factor (FGF), vascular endothelial growth factor (VEGF), trans-forming growth factor-beta1 and 2 (TGFβ1 and TGFβ2), and soluble collagen. A-PRF+ combined with fibroblasts demonstrated significantly higher values of released VEGF at every time point and, after 7 days, significantly higher values of released TGFβ2. A viability test after 72 h showed a significant increase in proliferation fibroblasts after exposition to the factors released from A-PRF+ combined with fibroblasts. Similarly, the degree of wound closure after 48 h was significantly higher for the factors released from A-RRF+ alone and the factors released from A-RRF+ combined with fibroblasts. These results imply that platelet-rich fibrin (PRF) enhanced with fibroblasts can be an alternative method of connective tissue transplantation.Addressing the severe deterioration of gap mode properties in spherical-shaped nanoparticles (NPs) becomes necessary due to their utilization in a wide range of multi-disciplinary applications. In this work, we report an integrated plasmonic nanostructure based on a spherical-shaped nanoparticle (NP) in a metallic hole as an alternative to a NP-only structure. With the help of three-dimensional (3D) electromagnetic simulations, we reveal that when a NP is positioned on the top of a metallic hole, it can exhibit superior gap-mode-based local-field intensity enhancement. The integrated nanostructure displayed a ~22-times increase in near-field enhancement characteristics, similar to cube- or disk-shaped nanostructure's plasmonic properties. From an experimental perspective, the NP positioning on top of the metallic hole can be realized more easily, facilitating a simple fabrication meriting our design approach. In addition to the above advantages, a good geometrical tolerance (metallic hole-gap size error of ~20 nm) supported by gap mode characteristics enhances flexibility in fabrication. These combined advantages from an integrated plasmonic nanostructure can resolve spherical-shaped NP disadvantages as an individual nanostructure and enhance its utilization in multi-disciplinary applications.In this paper, the welding thermal cycle process of deep-sea pipeline steel was investigated by welding thermal simulation. The microstructure evolution, crystallology and second-phase precipitation behavior of the soft zone of the heat-affected zone (HAZ) were characterized and analyzed by combining scanning electron microscopy, electron back-scattered diffraction, transmission electron microscopy and hardness testing. The results show that HAZ softening appeared in the fine-grained zone with a peak temperature of 900-1000 °C for deep-sea pipeline steel, the base metal microstructure of which was the polygonal ferrite and acicular ferrite. Using V microalloying and low welding heat input could effectively decrease the softening of the HAZ fine-grained region, which was achieved by reducing the effective grain size, increasing the proportion of the dislocation substructures, and precipitating the nanoscale second-phase particles.To investigate the action mechanism of titanium, the effects of different Ti-bearing compounds, including CaTiO3, MgTiO3, and nano-TiO2, on the properties of alumina-magnesia castables were studied. By analyzing the phase compositions, microstructures, and physical and mechanical properties of the castables, it was demonstrated that an intermediate product, CaTiO3, was first generated. This was then consumed by solid-solution reactions, and titanium was involved in the liquid formation as the temperature increased. The solid-solution reaction of CA6 (CaAl12O19) was more prominent due to the incorporation of more titanium in the crystal lattice of CA6 instead of spinel (MgAl2O4). Moreover, the liquid formation was strongly promoted when more titanium accompanied the calcium, which finally accelerated the densification and improved the strengths of alumina-magnesia castables. On the whole, castables with CaTiO3 addition presented higher bulk density and excellent strength after the heat treatment. Besides, the castables with 2 wt.% CaTiO3 contents were estimated to possess greater thermal shock resistance.Insulated-gate GaN-based transistors can fulfill the emerging demands for the future generation of highly efficient electronics for high-frequency, high-power and high-temperature applications. However, in contrast to Si-based devices, the introduction of an insulator on (Al)GaN is complicated by the absence of a high-quality native oxide for GaN. Trap states located at the insulator/(Al)GaN interface and within the dielectric can strongly affect the device performance. In particular, although AlGaN/GaN metal-insulator-semiconductor high electron mobility transistors (MIS-HEMTs) provide superior properties in terms of gate leakage currents compared to Schottky-gate HEMTs, the presence of an additional dielectric can induce threshold voltage instabilities. Similarly, the presence of trap states can be detrimental for the operational stability and reliability of other architectures of GaN devices employing a dielectric layer, such as hybrid MIS-FETs, trench MIS-FETs and vertical FinFETs. In this regard, the minapplications. Afterwards, novel emerging concepts using the Al2O3-based gate dielectric technology are introduced. Finally, the recent status of nitride-based materials emerging as other gate dielectrics is briefly reviewed.One of the basic assumptions of analytical dimensioning models of asphalt pavements is failure due to fatigue cracking of the bituminous layers. Furthermore, it is considered that the damaging effects of different traffic loads are linear and cumulative, per Miner's law. However, the analysis carried out on the effect of temperature, rest periods, and ageing of the bituminous materials questions considering fatigue failure as the only and main assumption for the calculation of the pavement life. Ageing of the pavement asphalt layers results in stiffening and transverse cracking. Consequently, these asphalt layers are no longer of infinite extent in the horizontal direction and their response resembles that of a slab. The application of this last calculation assumption provides pavement sections more in line with those used in Spain in the Catalogue of Structural Sections, which is based on experience gained from the real behavior of those sections. The calculation based on the fatigue laws results in undersized structures. This paper shows the results of a strain sweep test implemented at the UPC Roads Laboratory, which was used to analyse all the aforementioned effects and to propose a calculation procedure for heavy traffic pavements considering transverse cracking of the asphalt layers.In the present work, bismuth borate glass samples with the composition of (99-x) B2O3 + 1Cr2O3 + (x) Bi2O3 (x = 0, 5, 10, 15, 20, and 25 wt %) were prepared using the melt quenching technique. The mass attenuation coefficient (MAC) of the prepared glass samples was measured through a narrow beam technique using a NaI(Tl) scintillation detector. Four point sources were used (241Am, 133Ba, 152Eu, and 137Cs) to measure the MAC for the prepared glasses. The experimental data were compared with the theoretical results obtained from the XCOM, and it was shown that for all samples at all tested energies, the relative deviation between the samples is less than 3%. This finding signifies that the experimental data can adequately be used to evaluate the shielding ability of the glasses. The MAC of the sample with x = 25 wt % was compared with different lead borate glasses and the results indicated that the present sample has high attenuation which is very close to commercial lead borate glasses. We determined the transmission factor (TF), and found that it is small at low energies and increases as the energy increases. The addition of Bi2O3 leads to reduction in the TF values, which improves the shielding performance of the glass system. The half value layer (HVL) of the BCrBi-10 sample was 0.400 cm at 0.595 MeV, 1.619 cm at 0.2447 MeV, and 4.946 cm at 1.4080 MeV. Meanwhile, the HVL of the BCrBi-20 sample is equal to 0.171 and 4.334 cm at 0.0595 and 1.4080 MeV, respectively. The HVL data emphasize that higher energy photons tend to penetrate through the glasses with greater ease than lower energy photons. Furthermore, the fast neutron removable cross section (FNRC) was determined for the present samples and compared with lead borate glass and concrete, and the results showed a remarkable superiority of the bismuth borate glass samples.An exhaustive characterization of the physicochemical properties of gum arabic (GA)-coated Fe3O4 magnetic nanoparticles was conducted in this work. These nanoparticles were obtained via the in-situ coprecipitation method (a fast single-step method) in two GAFe ratios, 101 and 201, respectively. Several experimental techniques were applied in the characterization process, all of them described below. Using Transmission Electron Microcopy images, they were shown to have spherical-like morphology with 11 nm diameter. The Fourier Transform Infrared spectra confirmed the attachment of the GA on the surface of the magnetic nanoparticles (MNPs), providing good colloidal stability from pH 7 to 8. The thickness of the coatings (1.7 nm and 1.1 nm) was determined using thermogravimetric measurements. A high specific absorption rate and superparamagnetic properties were determined using alternant and static magnetic fields, respectively. The GA-coated MNPs were non-cytotoxic, according to tests on HT-29 human intestine cells.