Barrettmatthiesen7068

Patio Door Lock Repairs

Over time, patio door wear and tear can cause lock malfunctions. There are a few easy steps you can follow to ensure the security of your uPVC door.

These quick fixes will make your home safer, whether you realign the lock or clean the locking mechanism.

Clean the Lock

Patio doors are fantastic for bringing the outdoors in while keeping the elements out. However they could pose an issue for security in the event that the lock isn't working properly. Over time, wear and tear, hot and cold weather dirt, and other debris can cause your patio door lock to become difficult to operate. With a little maintenance, you can ensure your patio door's locks will always perform properly.

In the beginning, it's essential to clean your patio door's lock and all of its moving parts. This will help remove any dirt and coatings that may hinder the lock from working in the way it should. Start by wiping the moving parts of your patio door lock using an aqueous cloth. Then, use a scouring cloth or rough damp cloth to scrub the dirt-infested parts of the frame and door. Then clean the lock with a dry cloth to get rid of any moisture. Allow it to air-dry before using it.

If your patio door uses pin-tumbler latches you can apply powdered Graphite to the key. You can also use a Teflon lubricant like WD-40 Multi-Use Product. This type of lubricant is easy to apply and doesn't break down as time passes. If you're unable to find the correct lubricant for your lock, make use of a pencil with a larger tip. Insert the pencil into the lock and move it around a bit to distribute the graphite.

The tracks for sliding patio doors also require regular maintenance to ensure they're free of dirt, dust and other debris. These tracks are especially susceptible to snow and ice which could cause them to jam or bind, making it harder for your patio doors to open and close.

Tracks for sliding patio doors and rollers can be cleaned by removing any damaged or dirty weather stripping and then cleaning it, before replacing it. The rollers for patio doors can be cleaned and sprayed down with an oil that is nonstick.

Lubricate the moving parts

uPVC French Doors, similar to sliding patios, are operated by using 3 to 4 or occasionally 5 point locking mechanisms. They include the handle and lock cylinder that is operated with a key. These doors also need maintenance, specifically lubrication on the moving parts. This can be done using a thin oil (never WD40) and is recommended to be done at least once per year.

If sagging hinges aren't the cause, the door could be misaligned and caught or striking the strike plate hole in the frame. Remove the strike plate, and use a sharp tool to expand the mortise. This lets the latch sit perfectly in the hole and prevents rubbing or catching on the frame.

Find the length of the cylinder using an object of wood or a book that is able to fit into the space above the adjustment screw. The outer dimension is measured from the outside of the door to the center of cylinder. The inner dimension is measured from the center adjustment screw to the end cylinder.

Check the lock's length

If your patio door latch is hard to turn even after oiling and cleaning it could be because it's not aligned with the strike plate. Examine if the door is properly balanced and if the hinge screws are secure however, in many instances it is possible to move the strike plate up or down could fix the problem.

Oftentimes, the problem occurs when the lock's strike is too small for the latch to properly engage. In this situation, you'll need to enlarge the hole using a chisel or hammer and then test the latch to make sure that it contacts the strike plate without rubbing against or landing on the frame of the door jamb.

You must identify the kind of mortise lock you have before buying a replacement. This can be done by looking at the end faceplate and noting whether it is square or round. Look at each screw hole on the current lock and note the size. This will aid you in finding an alternative lock that is of the same size and will fit perfectly into your existing hole.

You'll want to identify the mortise lock, and then examine it for any scratches, bends or other damage that requires to be fixed. A bent or damaged latch is more likely to break than one that's been utilized often, so make sure to replace the lock with a brand new, secure version in the event you notice any signs of damage or wear.

After you've examined the lock and determined which kind of replacement you require now is the time to start working on the actual repair. The old spindle and handle should be removed from the patio door. Introduce the new handle. Begin by installing the handle inside and aligning it with the spindle and then securing it with the two bolts or screws that hold it. Install the exterior handle after the interior handle. After you've completed these steps, test the handles to make sure they are able to open and close easily and that the latch is in contact correctly with the strikeplate.

Check the Door's Strike

The strike plate and door latch are two parts that work together to secure the door. Misaligned strike plate and door latch will result in the latch not being able to latch the door in a proper manner. This issue is usually easy to solve.

First, inspect the holes in the strike plate's receiving to make sure they are free of obstructions, such as dirt or plastic plugs. Then loosen the keeper screws that keep the strike plate in place, allowing it to move vertically, but not separating it from the door frame. Then, adjust the strike plate so that its holes for receiving are aligned with the latch hooks on the door latch. Once the strike plate has been adjusted then tighten all screws, and test to see if the door closes smoothly.





These plates are difficult to reach for homeowners with sliding patio doors. However they are crucial to secure and unlock your door. These metal plates are located on the top and bottom jambs of the door where they support its latch. Then, the door latch is able to slide into the strike plate to form a seal when closed. If patio door repairs near me is damaged, rusted, or not installed correctly, it may prevent the latch from locking the door securely.

A misalignment between the strike plate and latch is one common cause for a patio lock to not close or stick. This can be checked with the "lipstick" test. Apply some lipstick along the edge of the deadbolt, then cover it with masking tape. When you shut the door the lipstick will leave a mark on the tape that will show exactly where the latch connects to the strike plate. If the mark is too high or low you can adjust the strike plate.

Sliding patio door locks help protect your home from burglars. If they're not working properly, you need to repair the issue quickly. By following these simple steps, you can repair your patio door's lock and get it back to normal within a short time.