Adamstopp8783

In order to support the best optimized design or strategy based on life-cycle data, the interrelation mechanisms between structure-form and structure-performance should be considered simultaneously and comprehensively besides of the material-property relationship. Here, the structure-property-performance relationship of a designed steel mega-sub controlled structural system (MSCSS) under the reported earthquake waves has been investigated through integrating the finite element simulations and the experimental validations. It can be found that the MSCSS configurations are capable of effectively optimizing the vibration responses with significantly decreased acceleration, which is also much better than the traditional megaframe structure with extra weight. Moreover, if the horizontal connections between the sub- and the megastructures are broken, the displacement of the megastructure will be smaller than that of the substructure. This is because only the vertical connections between the sub- and megastructures work, the larger displacements or the obvious response of the substructures should be caused by the extra weight of the damper on the top floor. It is worth mentioning that the formation of abrupt amplified β of the top floors should be attributed to the sheath effect. Furthermore, the displacement of the substructure is one kind of energy dissipation. Its larger displacement will result in a greater amount of energy dissipation and better performance of the designed configuration. This work supports a digital twin assistant active design and optimization strategy to further improve the control effectiveness of the system and to enhance the mechanical performance of the optimized configuration of MSCSS.Polyphenylene sulfones (PPSU) blends with different viscosities have been studied. It is shown that the blends have a single-phase structure, regardless of the viscosities of the mixed polymers. It was found that blends having close values of the melt flow index (MFR) are also characterized by a similar melt viscosity in a wide range of shear rates, regardless of the viscosities of its constituent components. It has been found that PPSU blends with smaller MFR differences exhibit higher heat resistance and stability of mechanical properties, while blends with similar viscosity containing oligomers exhibit a broader molecular weight distribution (MWD) and have lower thermal and mechanical properties.This study aimed to investigate the interaction parameters of antioxidant molecules in some spices and vegetables with gamma radiation. At first, mass attenuation coefficients (MACs, cm2/g) of gingerol, rosmarinic acid, quercetin, curcumin, eugenol, piperine, allicin, and capsaicin molecules were determined at the photon energies (13-1332 keV) emitted from the radioactive isotopes Am-241, Ba-133, Co-60, and Cs-137 with the help of the EpiXS and WinXCOM programs. The smallest and largest MAC values were found as 1.20 and 8.48 cm2/g at 13 keV and 0.059 and 0.058 cm2/g at 1332 keV for eugenol and allicin, respectively. It was observed that both results support each other. Using the MAC values, the effective atomic number and electron density (Zeff and Neff) values of the molecules were derived. The Zeff values for gingerol and allicin were obtained in the range of 5.79-3.40 and 13.85-4.53, respectively. The variation of the buildup factors of antioxidants in the range of 0.015-15 MeV depending on the chemical composition and penetration depth were also examined. It was noticed that the photon accumulation was the lowest in allicin and the highest in gingerol and eugenol. The results obtained from this study will make an essential contribution to dose calculations in food irradiation studies.The aim of this study was to determine the mechanical properties of laminated beams containing selected wood species in the tension zone using a four-point bending test. Three beam types were manufactured with respect to the timber used in the tension zone, i.e., beams containing oak or beech timber of I and II quality class and pine timber with no defects (as defects had been removed). The manufactured beams were assessed with respect to bending strength and the modulus of elasticity. The obtained results were compared with the performance of BSH (Industrial beams GL made in Germany-Brettschichtholz) industrial beams. Siremadlin purchase We concluded that beams made from pine timber are an appropriate alternative to spruce beams. The static bending strength of the beams made with hardwood faces was 70% higher than that of beams made with pine wood. All types of beams manufactured in the laboratory met the requirements of at least the GL24c class.The aim of this study is to assess the stress distribution on the bone tissue and bone-implant interface of a customized anatomic root-analog dental implant (RAI) by means of finite element analysis (FEA) for different types of bone density. A mandibular right second premolar was selected from the CBCT database. A DICOM file was converted to an STL file to create a CAD model in FEA software. The bone boundary model was created, while bone density types I-IV were determined. Von Mises stress was measured at bone tissues and bone-implant interfaces. To validate the models, the RAI was 3D printed through a laser powder-bed fusion (L-PBF) approach. The results revealed that all RAI designs could not cause plastic deformation or fracture resulting in lower stress than the ultimate tensile stress of natural bone and implant. Compared to a conventional screw-type implant, RAIs possess a more favorable stress distribution pattern around the bone tissue and the bone-implant interface. The presence of a porous structure was found to reduce the stress at cancellous bone in type IV bone density.In order to explore the effect of the foaming agent type on the properties of foamed mixture lightweight soil mixed with bauxite tailings (FMLSB), low-density (437.5 kg/m3 and 670 kg/m3) and high-density (902.5 kg/m3 and 1170 kg/m3) FMLSB were prepared using protein-based and synthetic-based foaming agents (AF and SF, respectively). The foam stability, micro characteristics, compressive strength, fluidity, and volume of water absorption of the FMLSB were investigated. The results showed that the foam made from AF had better strength and stability compared to SF. The internal pore sizes of both AF- and SF-FMLSB at low density were large, but at high density the internal pore sizes and area porosity of AF-FMLSB were smaller than those of SF-FMLSB. In terms of compressive strength, the compressive strength of AF-FMLSB was improved by 17.5% to 43.2% compared to SF-FMLSB. At low density, the fluidity of AF- and SF-FMLSB is similar, while at high density the fluidity of AF-FMLSB is much higher than that of SF-FMLSB. In addition, the stable volume of water absorption of SF-FMLSB is smaller than that of AF-FMLSB at low density, and the corresponding water resistance is better, but the situation is reversed at high density.Significant efforts have been made to improve adsorbents capable of eliminating pollutants from aqueous solutions, making it simple and quick to separate from the treated solution. In the current study, the removal of Crystal Violet Dye (CVD) from an aqueous synthetic solution onto a marine diatom alga, Skeletonema costatum, was investigated. Different experiments were conducted as a function of different pH, contact time, adsorbent dosage, temperature, and initial CVD concentration. The highest adsorption efficiency (98%) was obtained at 0.4 g of S. costatum, pH 3, and a contact time of 120 min, at 25 °C. Furthermore, Fourier-transform infrared spectroscopy (FTIR) results display that binding of CVD on S. costatum may occur by electrostatic and complexation reactions. Moreover, the Brunauer-Emmett-Teller surface area analysis (BET) obtained was 87.17 m2 g-1, which, in addition to a scanning electron microscope (SEM), reveals large pores that could enhance the uptake of large molecules. However, the equilibrium adsorption models were conducted by Halsey, Langmuir, Freundlich, Henderson, and Tempkin isotherm. In addition, multilayer adsorption isotherm best described the uptake of CVD onto S. costatum. The maximum monolayer adsorption capacity (qmax) was 6.410 mg g-1. Moreover, thermodynamic parameters of the adsorption studies suggested that the uptake of CVD onto S. costatum was endothermic and spontaneous. The pseudo-first-order, pseudo-second-order, and intra-particle diffusion kinetic equations were applied to model the adsorption kinetic data. It was seen that the kinetics of the adsorption may be described using pseudo-second-order kinetic equations. Finally, the present work concluded that the marine diatom alga S. costatum is suitable as a natural material for the adsorption of CVD.The research and development of rocket propellants with a high solid content and superior mechanical and security performance is urgently needed. In this paper, a novel extruded modified double-base (EMDB) rocket propellant plasticized by N-butyl-N-nitratoethyl nitramine (Bu-NENA) was prepared to overcome this challenge. The results indicated that Bu-NENA decreased the mechanical sensitivity successfully, contributing to the mechanical properties against traditional nitroglycerin (NG) based EMDB propellants, while hexogen (RDX), which is beneficial to propellant energy, was not conducive to the elongation and sensitivity of the propellants. By contrast with the blank group (NG-based EMDB propellant, R0), the elongation of the optimized propellant at -40 °C was promoted by 100% from 3.54% to 7.09%. Moreover, the β-transition temperature decreased from -33.8 °C to -38.1 °C due to superior plasticization by Bu-NENA, which represents a better toughness. The friction sensitivity dropped by 100% from 46% to 0%. Simultaneously, the height for 50% probability of explosion (H50) increased by 87.2% from 17.2 cm to 32.2 cm. The results of this research could be used to predict a potential prospect in tactical weapons.Hydrogen fuel cells have been used worldwide due to their high energy density and zero emissions. The metallic bipolar plate is the crucial component and has a significant effect on a cell's efficiency. However, the springback behavior of the metallic bipolar plate will greatly influence its forming accuracy in the micro-scale sheet metal forming process. Therefore, accurate calculation of the springback angle of the micro-scale metallic bipolar plate is urgent but difficult given the state of existing elastoplastic theory. In this paper, a constitutive model that simultaneously considers grain size effect and strain gradient is proposed to analyze micro-scale bending behavior and calculate springback angles. The specialized micro-scale four-point bending tool was designed to better calculate the springback angle and simplify the calculation step. A pure micro-bending experiment on a 316LN stainless steel sheet with a thickness of 0.1 mm was conducted to verify the constitutive model's accuracy.In the pressurized water reactor nuclear power plant, 316L SS chips were captured by the support grid and continued to affect the Zr-4 cladding tube, causing the fuel rods to wear and perforate. In this work, a 60° acute angle cone of 316L SS was used to simulate the cyclic impact of debris on a Zr-4 alloy tube with different initial impact velocities and impact angles. Results showed that increasing the initial impact velocity will generate a wear debris accumulation layer with a wear-reducing effect, but also promote the extension and expansion of fatigue cracks, resulting in the delamination of Zr-4 alloy tubes. The inclination of the impact angle increases the energy loss. The energy loss rate of the 45° impact is as high as 69.68%, of which 78% is generated by the impact-sliding stage. The normal force is mainly responsible for the wear removal and plastic deformation of Zr-4 alloy tubes. Tangential forces cause severe cutting in Zr-4 alloys and pushes the resulting wear debris away from the contact surfaces.