Underwoodgregory7568

The challenges of making a direct comparison between the core-shell particle-reinforced MMCs and MMCs of other microstructures and future research directions are discussed.Magnetic polymers are often used as loading materials for ionic liquids because of their excellent magnetic separation properties. In this study, a novel imidazolium-based ionic liquid-modified magnetic polymer was synthesized by suspension polymerization and grafting, denoted as γ-Fe2O3@GMA@IM, and this magnetic polymer was used for the adsorption of the acid dye FCF. The magnetic polymer was characterized by SEM, FTIR, XRD, VSM and TGA. These techniques were used to reveal the overall physical properties of magnetic polymers, including the presence of morphology, functional groups, crystalline properties, magnetism and thermal stability. Studies have shown that γ-Fe2O3@GMA@IM can adsorb FCF in a wide pH range (2-10), with a maximum adsorption capacity of 445 mg/g. The adsorption data were more in line with the pseudo-second-order kinetic model and the Freundlich isotherm. In order to investigate its reusability, this study used 10% NaCl as the desorption solution, and carried out five batches of adsorption-desorption cycles. After five cycles, the adsorption effect was maintained at 98.3%, which showed a good recycling performance.The kinetics and mechanism of ternesite formation (calcium sulfosilicate, Ca5(SiO4)2SO4, C5S2$) were investigated by studying the reaction between beta-dicalcium silicate (β-C2S) and calcium sulfate dihydrate (CaSO4∙2H2O). Mineralogical composition development was monitored using X-ray diffraction (XRD) and backscattered scanning electron microscopy (BSEM) coupled to energy-dispersive X-ray spectroscopy (EDS). Ternesite can form in the 1100 to 1200 °C range by the solid-phase reaction of β-C2S and CaSO4. The formation of ternesite is favored by increasing the sintering temperature or extending the sintering time. The solid-phase reaction is carried out by diffusion of CaSO4 to β-C2S. The kinetics equation of ternesite is consistent with three-dimensional diffusion models (3-D model, D3 model or Jander model). The equation of the D3 model is 1 - 2α/3 - (1 - α)2/3 = kt. On the basis of the Arrhenius equation, the activation energy of ternesite is 239.8 kJ/mol.The structural design process is iterative and involves many design parameters. Thus, this paper presents a controlled framework for selecting the adequate structural floor system for reinforced concrete buildings and efficiently utilizing the corresponding construction materials. Optimization was performed using an evolutionary algorithm to minimize the total construction cost, considering the costs of concrete, steel reinforcement, formwork, and labor. In the problem formulation, the characteristic compressive strength of concrete was treated as a design variable because it affects the mechanical performance of concrete. The design variables included the column spacings, concrete dimensions, and steel reinforcement of different structural components. The constraints reflected the Egyptian code of practice provisions. Because the choice of the structural floor system affects the design details, three systems were considered solid slabs, flat slabs with drop panels, and flat slabs without drop panels. Two benchmark examples were presented, and the optimal design results of the structural floor systems were compared. The solid slab system had the lowest construction cost among the three structural floor systems. Comparative diagrams were developed to investigate the distribution of construction costs of each floor system. The results revealed that an adequate choice of design variables could save up to 17% of the building's total construction cost.In this study, we propose a solution process for realizing colored glass for building integrated photovoltaic (BIPV) systems by spin coating a color solution composed of pearlescent pigments mixed in a Norland Optical Adhesive (NOA) matrix. Color solutions are made from mixing pearlescent pigments in NOA63. Compared to a physical vapor deposition process, color coatings are achieved by spin coating in a relatively simple and inexpensive process at room temperature. The optical properties can be easily controlled by adjusting the spin coating speed and the concentration of the pearlescent pigments. The produced colored glass achieved a high transmittance of 85% or more in the visible wavelength range, except for the wavelength spectrum exhibiting the maximum reflectance. In addition, we propose a one-step lamination process of colored glass on a solar cell by leveraging on the adhesive property of the NOA matrix. This eliminates the cost and process of additional ethylene vinyl acetate (EVA) layer or other materials used in the conventional lamination process. The colored glass produced through this study has stability that does not change its properties over time. Therefore, it is expected to be applied to the BIPV solar module market where aesthetics and energy efficiency are required.Ultrasonic technology is being increasingly explored in minerals processing. In this paper, ultrasonic treatment was introduced as a novel method for microbial desulfurization of sulfide ores. A Box-Behnken experiment was performed to find the best combination of factor levels for the following experiments; consequently, the combination of factor levels at the maximum 5-day average desulfurization rate at 20 g of ore was a particle size of 120-140 mesh, a shaker speed of 175 rpm, and a dosage of 111 mL of bacterial solution. Under these conditions, a microbial desulfurization experiment of sulfide ores by ultrasonic treatment was carried out, and the effect of the particle size, the ultrasonic action time, and the ultrasonic power were investigated. Results indicated that the ultrasonic effect was not significant for ore samples with larger particle sizes, and the appropriate increase in ultrasonic action time was beneficial to the improvement of desulfurization rate, but the effect showed a decreasing trend when it exceeded 50 min, and the best desulfurization effect was achieved when the power was 300 W. This study demonstrated that the effect of microbial desulfurization can be greatly enhanced by ultrasonic treatment.Due to the advantages of relatively low cost, increased energy efficiency, increased deposition rate, and the capacity to create medium to large scale components, wire + arc additive manufacturing (WAAM) has gained growing interest. Super martensitic stainless steel (SMSS) combines outstanding strength, ductility, and corrosion resistance, making it a great option for WAAM. In the present work, an SMSS component was successfully produced by WAAM. Additionally, the influence of post-manufactured heat treatment on the microstructural characteristics and mechanical properties of SMSS components was systematically examined. A microstructural analysis of the as-printed and heat-treated samples revealed the formation of typical martensite and a small amount of retained austenite. Ceftaroline However, the sample heat-treated by solutionizing at 1050 °C for 1 h followed by aging at 400 °C for 2 h exhibited a finer martensitic structure with an effective grain size of 5.6 μm compared to as-printed sample, leading to an increase in ultimate tensile strength from 1054 ± 6 MPa to 1141 ± 3 MPa with a concomitant increase in elongation from 7.8 ± 0.4% to 12.6 ± 0.2%. Additionally, the fracture morphology of the solution + aging sample demonstrated a more uniform distribution and greater mean size of dimples, indicating better ductility.Petroleum substances are among the xenobiotics that most often contaminate the natural environment. They have a strong effect on soil, water, and other components of the environment. The aim of this pot experiment has been to determine the effect of different soil material amendments (compost, 3%; bentonite, 2% relative to the soil mass or calcium oxide, in amounts corresponding to one full hydrolytic acidity) on the content of heavy metals in aerial parts of maize (Zea mays L.) grown on soil polluted with petrol (0, 2.5, 5, and 10 cm3 kg-1 of soil). The content of all heavy metals, except copper, in the aerial biomass of maize was positively correlated, but biomass yield negatively correlated, with the increasing doses of petrol. The highest increase in the content of heavy metals was noted for chromium and manganese. Materials used for phytostabilisation (compost, bentonite, and calcium oxide) had a significant effect on the content of heavy metals and biomass yield of maize. They contributed to the modified accumulation of elements, especially chromium, copper, and cobalt in the aerial biomass of maize. In comparison with the control series (without material amendments), the application of calcium oxide proved to be most effective. It had the most evident influence on the chemical composition of maize, limiting the accumulation of lead, zinc, manganese, and iron and increasing biomass yield.The manipulation of composition and pressure, which affect the structure and, as a result, lead to new desired properties, is particularly significant for optimizing device performance. By considering the importance of pressure treatment, this study explores bandgap engineering and tuned optical responses of the ternary Cd0.25Zn0.75S alloy over a pressure range of 0-20 GPa using density functional theory. The functional material exhibits cubic symmetry at all pressures, and its bulk modulus increases with pressure. It is a direct bandgap semiconductor at Γ symmetry point, and its bandgap energy increases from 3.35 eV to 3.86 eV with an increase in pressure. Optical properties change with pressure, such that the absorption coefficient increases and absorbs near-ultraviolet light, while the static dielectric constant and static refractive index both increase with pressure. The effects of pressure on other optical parameters such as dielectric constant, extinction coefficient, refractive index, optical conductivity, and reflection are also explored. These findings provide significant theoretical guidance for the use of the Cd0.25Zn0.75S semiconductor in fabricating optoelectronic and photovoltaic devices functioning at varying pressure ranges and altitudes.Hadfield steel, under unit pressure conditions, strengthens itself by forming a high density dislocation structure, which results in increased resistance to dynamic impact wear. However, under abrasion conditions, the homogeneous microstructure of the cast steel is insufficient to achieve the expected service life. The aim of the research is to conduct a comparative analysis of the material in its as-delivered state and after two-stage heat treatment (isothermal annealing followed by re-austenitisation). It was found that after isothermal annealing of X120Mn12 grade steel at a temperature of 510 °C, a microstructure with a complex morphology consisting of colonies of fine-grained pearlite, (Fe,Mn)3C carbides distributed along the grain boundaries of the former austenite and needle-like (Fe,Mn)3C carbides was obtained in the austenite matrix. The subsequent thermal treatment of the steel with the use of supersaturating annealing at 900 °C resulted in a heterogeneous microstructure consisting of evenly distributed globular carbide precipitations in a matrix of considerably finer austenite grains in comparison with the as-delivered original state.