Svenstrupthomsen9387

The use of wood plastic composites (WPC) is growing very rapidly in recent years, in addition, the use of plastics of renewable origin is increasingly implemented because it allows to reduce the carbon footprint. In this context, this work reports on the development of composites of bio-based high density polyethylene (BioHDPE) with different contents of pinecone (5, 10, and 30 wt.%). The blends were produced by extrusion and injection-molded processes. With the objective of improving the properties of the materials, a compatibilizer has been used, namely polyethylene grafted with maleic anhydride (PE-g-MA 2 phr). The effect of the compatibilizer in the blend with 5 wt.% has been compared with the same blend without compatibilization. Mechanical, thermal, morphological, colorimetric, and wettability properties have been analyzed for each blend. The results showed that the compatibilizer improved the filler-matrix interaction, increasing the ductile mechanical properties in terms of elongation and tensile strength. Regarding thermal properties, the compatibilizer increased thermal stability and improved the behavior of the materials against moisture. In general, the pinecone materials obtained exhibited reddish-brown colors, allowing their use as wood plastic composites with a wide range of properties depending on the filler content in the blend.Foam products are one of the largest markets for polyurethane (PU) and are heavily used in many sectors. However, current PU formulations use highly toxic and environmentally unfriendly production processes. Meanwhile, the increasing environmental concerns and regulations are intensifying the research into green and non-toxic products. In this study, we synthesized flexible polyurethane foam (PUF) using different weight percentages (0.025%, 0.05% and 0.1%) of a non-toxic bismuth catalyst. The bismuth-catalyzed foams presented a well evolved cellular structure with an open cell morphology. The properties of the bismuth-catalyzed flexible PUF, such as the mechanical, morphological, kinetic and thermal behaviors, were optimized and compared with a conventional tin-catalyzed PUF. The bismuth-catalyst revealed a higher isocyanate conversion efficiency than the stannous octoate catalyst. When comparing samples with similar densities, the bismuth-catalyzed foams present better mechanical behavior than the tin-catalyzed sample with similar thermal stability. The high solubility of bismuth triflate in water, together with its high Lewis acidity, have been shown to benefit the production of PU foams.Electrically conductive polymeric nanocomposites with nanoparticles are adaptable types of nanomaterials that are prospective for various applications. The extraordinary features of copper oxide (CuO) and aluminium oxide (Al2O3) nanostructures, encourages extensive studies to prospect these metal oxide nanocomposites as potential electroactive materials in sensing and biosensing applications. This study suggested a new CuO/Al2O3 nanocomposite-based polymeric coated wire membrane sensor for estimating naltrexone hydrochloride (NTX) in commercial formulations. Naltrexone hydrochloride and sodium tetraphenylborate (Na-TPB) were incorporated in the presence of polymeric polyvinyl chloride (PVC) and solvent mediator o-nitrophenyloctyl ether (o-NPOE) to form naltrexone tetraphenylborate (NTX-TPB) as an electroactive material. The modified sensor using NTX-TPB-CuO/Al2O3 nanocomposite displayed high selectivity and sensitivity for the discrimination and quantification of NTX with a linearity range 1.0 × 10-9-1.0 × 10-2 mol L-1 and a regression equation EmV = (58.25 ± 0.3) log [NTX] + 754.25. Contrarily, the unmodified coated wire sensor of NTX-TPB exhibited a Nernstian response at 1.0 × 10-5-1.0 × 10-2 mol L-1 and a regression equation EmV = (52.1 ± 0.2) log [NTX] + 406.6. The suggested modified potentiometric system was validated with respect to various criteria using the methodology recommended guidelines.The synthesis of surface-grafted polymers with variable functionality requires the careful selection of polymerization methods that also enable spatially controlled grafting, which is crucial for the fabrication of, e.g., nano (micro) sensor or nanoelectronic devices. The development of versatile, simple, economical, and eco-friendly synthetic strategies is important for scaling up the production of such polymer brushes. We have recently shown that poly (3-methylthienyl methacrylate) (PMTM) and poly (3-trimethylsilyl-2-propynyl methacrylate) (PTPM) brushes with pendant thiophene and acetylene groups, respectively, could be used for the production of ladder-like conjugated brushes that are potentially useful in the mentioned applications. However, the previously developed syntheses of such brushes required the use of high volumes of reagents, elevated temperature, or high energy UV-B light. Therefore, we present here visible light-promoted metal-free surface-initiated ATRP (metal-free SI-ATRP) that allows the economical synthesis of PMTM and PTPM brushes utilizing only microliter volumes of reaction mixtures. The versatility of this approach was shown by the formation of homopolymers but also the block copolymer conjugated brushes (PMTM and PTPM blocks in both sequences) and patterned films using TEM grids serving as photomasks. selleck A simple reaction setup with only a monomer, solvent, commercially available organic photocatalyst, and initiator decorated substrate makes the synthesis of these complex polymer structures achievable for non-experts and ready for scaling up.Construction of oil and gas wells at offshore fields often involves high formation pressure and the presence of swellable clay rocks in the section. link2 In addition, productivity preservation is also an important aspect. For this purpose, it is necessary to reduce the solids content of the drilling mud. The purpose of this work is to develop, improve, and study compositions of weighted drilling muds with low content of solids, on the basis of organic salts of alkali metals and polymers for the construction of wells prone to rock swelling and/or cavings, as well as drilling fluids for drilling-in the formation. In order to achieve the set goal the following is required Analysis of existing drilling muds of higher density for drilling wells in unstable rock intervals and for drilling in the productive formation; analysis of experience in using drilling systems on the formic acid salts base and substantiation of requirements for flushing fluids during well construction; development and investigation of drilling mud compositions on the formate base; and the evaluation of inhibiting effect of systems containing organic salts, polymer reagents, and calcium carbonate on clay samples. The developed drilling mud is characterized by a high inhibiting ability that allows minimized mud-weighting by the natural solid phase. This reduces the volume of prepared mud and facilitates the regulation of its properties by reducing the dispersion of drilled cuttings; it eliminates problems related to hydration and the swelling of active clay rocks; and stabilizes unstable argillites prone to caving. The low solids content, low filtration rates, and inhibitory nature of the mud allows high stability of the rheological properties of the mud, and preserves oil and gas reservoir productivity under conditions of elevated formation pressure.This paper gives a short overview of homogeneous post-metallocene catalysts based on group 4 metal and vanadium complexes bearing multidentate ligands. It summarizes the catalytic behavior of those catalysts in copolymerization of ethylene with 1-olefins, with styrenic monomers and with α,ω-alkenols. The review is focused on finding correlations between the structure of a complex, its catalyst activity and comonomer incorporation ability, as well as the microstructure of the copolymer chains.A new strain of bacteria producing cellulose was isolated from Kombucha and identified as Komagataeibacter hansenii, named SI1. In static conditions, the strain synthesises bacterial nanocellulose with an improved ability to stretch. In this study, utilisation of various carbon and nitrogen sources and the impact of initial pH was assessed in terms of bacterial nanocellulose yield and properties. K. link3 hansenii SI1 produces cellulose efficiently in glycerol medium at pH 5.0-6.0 with a yield of 3.20-3.60 g/L. Glucose medium led to the synthesis of membrane characterised by a strain of 77%, which is a higher value than in the case of another Komagataeibacter species. Supplementation of medium with vitamin C results in an enhanced porosity and improves the ability of bacterial nanocellulose to stretch (up to 123%). The properties of modified membranes were studied by scanning electron microscopy, Fourier transform infrared spectroscopy, X-ray diffraction and mechanical tests. The results show that bacterial nanocellulose produced in SH medium and vitamin C-supplemented medium has unique properties (porosity, tensile strength and strain) without changing the chemical composition of cellulose. The method of production BNC with altered properties was the issue of Polish patent application no. P.431265.Polymer extrudate swelling is a rheological phenomenon that occurs after polymer melt flow emerges at the die exit of extrusion equipment due to molecular stress relaxations and flow redistributions. Specifically, with the growing demand for large scale and high productivity, polymer pipes have recently been produced by extrusion. This study reports the development of a new incompressible non-isothermal finite volume method, based on the Arbitrary Lagrangian-Eulerian (ALE) formulation, to compute the viscous flow of polymer melts obeying the Herschel-Bulkley constitutive equation. The Papanastasiou-regularized version of the constitutive equation is employed. The influence of the temperature on the rheological behavior of the material is controlled by the Williams-Landel-Ferry (WLF) function. The new method is validated by comparing the extrudate swell ratio obtained for Bingham and Herschel-Bulkley flows (shear-thinning and shear-thickening) with reference data found in the scientific literature. Additionally, the essential flow characteristics including yield-stress, inertia and non-isothermal effects were investigated.The Hummers method is the most commonly used method to prepare graphene oxide (GO). However, many waste acids remain in the raw reaction mixture after the completion of this reaction. The aim of this study was to reuse these waste acids efficiently. In this study, microcrystalline cellulose (MCC) was directly dissolved in the mixture after the high-temperature reaction of the Hummers method. The residual acid was used to hydrolyze MCC, and the graphene oxide/microcrystalline cellulose (GO/MCC) composites were prepared, while the acid was reused. The effects of MCC addition (0.5 g, 1.0 g, and 1.5 g in 20 mL) on the properties of the composites were discussed. The structure, composition, thermal stability, and hydrophobicity of GO/MCC composites were characterized and tested by SEM, XRD, FTIR, TG, and contact angle tests. The results showed that MCC could be acid hydrolyzed into micron and nano-scale cellulose by using the strong acidity of waste liquid after GO preparation, and it interacted with the prepared GO to form GO/MCC composites.