Sharpethorhauge5065

The in vitro assays demonstrated adequate form, pore size of composites ranging from few micrometers up to 100 μm, while the self-assembled apatite layer formed after simulated body fluid immersion confirmed the composites' bioactivity. Viability assays have highlighted optimal cellular proliferation and in vitro biocompatibility for all tested composites. Furthermore, based on the in vivo subcutaneous analyses the polymer composites with BGAuNP have shown excellent biocompatibility at 14, 30 and 60 days, exhibiting marked angiogenesis while, tissue proliferation was confirmed by high number of Vimentin positive cells, in comparison with the polymer composite that contains βTCP/HA, which induced an inflammatory response represented by a foreign body reaction. The obtained results suggest promising, innovative, and biocompatible composites with bioactive properties for future soft tissue and bone engineering endeavours.Inadequate self-repair and regenerative efficiency of the cartilage tissues has motivated the researchers to devise advanced and effective strategies to resolve this issue. Introduction of bioprinting to tissue engineering has paved the way for fabricating complex biomimetic engineered constructs. In this context, the current review gears off with the discussion of standard and advanced 3D/4D printing technologies and their implications for the repair of different cartilage tissues, namely, articular, meniscal, nasoseptal, auricular, costal, and tracheal cartilage. The review is then directed towards highlighting the current stem cell opportunities. On a concluding note, associated critical issues and prospects for future developments, particularly in this sphere of personalized medicines have been discussed.Nanostructured Zn1-xYbxO (0.0 ≤ x ≤ 0.1) powders were prepared by the solution method using polyvinyl alcohol (PVA) and sucrose. The effect of the ytterbium doping content on the structural, morphological, optical and antimicrobial properties was analyzed. X-ray diffraction (XRD) analysis revealed that the hexagonal wurtzite structure was retained, and no secondary phases due to doping were observed. The crystallite size was under 20 nm for all the Zn1-xYbxO (0.0 ≤ x ≤ 0.1) powders. The optical band gap was calculated, and the results revealed that this value increased with the ytterbium content, and the Eg values varied from 3.06 to 3.10 eV. The surface chemistry of the powders was analyzed using X-ray photoelectron spectroscopy (XPS), and the results confirmed the oxidation state of ytterbium as 3+ for all the samples. Zn1-xYbxO (0.0 ≤ x ≤ 0.1) nanoparticles were tested as antimicrobial agents against Staphylococcus aureus and Escherichia coli, resulting in a potential antimicrobial effect at most of the tested concentrations. These results were used in an artificial neural network (ANN). The results showed that it is possible to generate a model capable of forecasting the absorbance with good precision (error of 1-2%).Muscle tissue possess an innate regenerative potential that involves an extremely complicated and synchronized process on which resident muscle stem cells play a major role activate after an injury, differentiate and fuse originating new myofibers for muscle repair. Considerable efforts have been made to design new approaches based on material systems to potentiate muscle repair by engineering muscle extracellular matrix and/or including soluble factors/cells in the media, trying to recapitulate the key biophysical and biochemical cues present in the muscle niche. This work proposes a different and simple approach to potentiate muscle regeneration exploiting the interplay between specific cell membrane receptors. The simultaneous stimulation of borate transporter, NaBC1 (encoded by SLC4A11gene), and fibronectin-binding integrins induced higher number and size of focal adhesions, major cell spreading and actin stress fibers, strengthening myoblast attachment and providing an enhanced response in terms of myotube fusion and maturation. The stimulated NaBC1 generated an adhesion-driven state through a mechanism that involves simultaneous NaBC1/α5β1/αvβ3 co-localization. We engineered and characterized borax-loaded alginate hydrogels for an effective activation of NaBC1 in vivo. After inducing an acute injury with cardiotoxin in mice, active-NaBC1 accelerated the muscle regeneration process. Our results put forward a new biomaterial approach for muscle repair.The paper focuses on the SiOx-doped amorphous hydrocarbon (a-CHSiOx) coating on the titanium (Ti-6Al-4V) alloy substrate obtained by plasma-assisted chemical vapor deposition (PACVD) in a mixture of argon gas and polyphenylmethylsiloxane vapor using a bipolar substrate bias. It is shown that the a-CHSiOx coating deposition results in the formation of a negative surface potential important for application of this coating for medical implants. selleck kinase inhibitor The a-CHSiOx coatings improve the corrosion resistance of Ti alloy to 0.5 M NaCl solution and phosphate-buffered saline. In particular, the corrosion current density of the a-CHSiOx-coated sample in a 0.5 M NaCl solution at 22 °C decreases from 1∙10-8 to 1.7∙10-10 A/cm2, that reduces the corrosion rate from 9∙10-5 to 15∙10-7 mm/year. The a-CHSiOx coating facilitates the surface endothelization of an implant located in the thoracic aorta of a mini pig, and reduces the risk of thrombosis and implant failure. This effect can be explained by the ability of the a-CHSiOx coating ability to reduce in vitro a 24-hour secretion of pro-inflammatory interleukins (IL-6, IL-12(p70), IL-15, and IL-17) and cytokines (IFN-g and TNF-a) by blood mononuclear cells (MNCs) and elevates the concentration of anti-inflammatory interleukin IL-1Ra. In vitro analysis shows no cytotoxicity of the a-CHSiOx coating for the human blood MNCs, suggesting a promising PACVD on Ti alloys for cardiovascular implants, including pumps for mechanical heart support systems.Here, an asymmetric double-layer membrane has been designed and fabricated by electrospinning as a tool for a potential wound healing application. A hydrophobic layer has been produced by using a polyurethane-polycaprolactone (PU-PCL) copolymer and loaded with the antibacterial ciprofloxacin whereas an ion responsive hydrophilic layer has been produced by using an octyl derivative of gellan gum (GG-C8) and polyvinyl alcohol (PVA) and loaded with the growth factor FGF-2. This study investigated how the properties of this asymmetric membrane loaded with actives, were influenced by the ionotropic crosslinking of the hydrophilic layer. In particular, the treatment in DPBS and the crosslinking in CaCl2 0.1 or 1 M of the hydrophilic layer affected the release profile of the bioactive molecules allowing to modulate both the antimicrobial effect, as assayed by logarithmic reduction of the Staphylococcus aureus viable count, and the chemoattractant properties on NIH 3 T3 cell line, as assayed by scratch test and cell chemoattraction assay.