Michaelsenlopez4256

Due to their excellent mechanical and thermal properties and medium resistance, epoxy/carbon nanotubes and nanocomposites have been widely used in many fields. However, the conventional thermosetting process is not only time- and energy-consuming, but also causes the agglomeration of nanofillers, which leads to unsatisfactory properties of the obtained composites. In this study, multi-walled carbon nanotubes (MWCNTs)/epoxy nanocomposites were prepared using UV photoinduced frontal polymerization (PIFP) in a rapid fashion. The addition of MWCNTs modified by a surface carboxylation reaction was found to enhance the impact strength and heat resistance of the epoxy matrix effectively. The experimental results indicate that with 0.4 wt % loading of modified MWCNTs, increases of 462.23% in the impact strength and 57.3 °C in the glass transition temperature Tg were achieved. A high-performance nanocomposite was prepared in only a few minutes using the PIFP approach. Considering its fast, energy-saving, and environmentally friendly production, the PIFP approach displays considerable potential in the field of the fast preparation, repair, and deep curing of nanocomposites and coatings.No study to date has simultaneously examined the commonalities and unique aspects of positive psychological factors and whether these factors uniquely account for a reduction in suicide risk. Using a factor analytic approach, the current study examined the relationships between grit, hope, optimism, and their unique and overlapping relationships in predicting suicide ideation. Results of principle axis factor analysis demonstrated close relationships between these variables at both the construct and item level. Item-level analyses supported a five-factor solution (Stick-to-Itiveness, Poor Future, Consistency of Interest, Positive Future, and Poor Pathways). Four of the five factors (excluding Stick-to-Itiveness) were associated with suicide ideation. Additionally, results of a multiple regression analysis indicated that two of the five factors (Consistency of Interest and Positive Future) negatively predicted suicide ideation while Poor Future positively predicted suicide ideation. Implications regarding the interrelationships between grit, hope, and optimism with suicide ideation are discussed.Strontium Titanate has a typical perovskite structure with advantages of low cost and photochemical stability. However, the wide bandgap and rapid recombination of electrons and holes limited its application in photocatalysis. In this work, a SrTiO3 material with surface oxygen vacancies was synthesized via carbon reduction under a high temperature. It was successfully applied for photocatalytic overall water splitting to produce clean hydrogen energy under visible light irradiation without any sacrificial reagent for the first time. The photocatalytic overall water splitting ability of the as-prepared SrTiO3-C950 is attributed to the surface oxygen vacancies that can make suitable energy levels for visible light response, improving the separation and transfer efficiency of photogenerated carriers.(1) Background survivors of allogeneic hematopoietic cell transplantation (alloHCT) suffer from morbidity and mortality due to cardiovascular events. We hypothesized that vascular injury and pro-coagulant activity are evident in alloHCT survivors without existing alloHCT complications or relapse. (2) Methods we enrolled consecutive adult alloHCT survivors without established cardiovascular disease and control individuals matched for traditional cardiovascular risk factors (January-December 2019). learn more Circulating microvesicles (MVs) of different cellular origins (platelet, erythrocyte, and endothelial) were measured by a standardized flow cytometry protocol as novel markers of vascular injury and pro-coagulant activity. (3) Results we recruited 45 survivors after a median of 2.3 (range 1.1-13.2) years from alloHCT, and 45 controls. The majority of patients suffered from acute (44%) and/or chronic (66%) graft-versus-host disease (GVHD). Although the two groups were matched for traditional cardiovascular risk factors, alloHCT survivors showed significantly increased platelet and erythrocyte MVs compared to controls. Within alloHCT survivors, erythrocyte MVs were significantly increased in patients with a previous history of thrombotic microangiopathy. Interestingly, endothelial MVs were significantly increased only in alloHCT recipients of a myeloablative conditioning. Furthermore, MVs of different origins showed a positive association with each other. (4) Conclusions endothelial dysfunction and increased thrombotic risk are evident in alloHCT recipients long after alloHCT, independently of traditional cardiovascular risk factors. An apparent synergism of these pathophysiological processes may be strongly involved in the subsequent establishment of cardiovascular disease.In the study, the friction stir processing (FSP) method was used to modify the surface layer of a tin-based bearing alloy. The modification was aimed at extending the service life of bearings by improving their tribological properties. The results of investigations of the microstructure, hardness and tribological properties of the SnSbCu bearing alloy after FSP using various rotational speeds of the tool-280, 355, 450 and 560 RPM-and the constant traverse speed of 355 mm/min are presented. Particular attention was paid to the possibility of changing the morphology of the precipitates present in the alloy, and to the impact of this parameter on improvement of the tribological properties. The research carried out in this paper covered investigations of the microstructure using light and scanning electron microscopy (SEM) along with analysis of the chemical composition in micro-areas and Brinell hardness tests. Additionally, the sizes of the SnSb and CuSn precipitates present in the microstructure before and after the modification process were determined, as were the tribological properties under technically dry friction conditions and lubrication with TU 32 oil. It was proven that using friction stir processing favors refinement of the microstructure and improves the tribological properties of the analyzed alloy.