Hayesrobinson0431

An aqueous fabrication process was developed which both increased capacity and improved stability and was amenable to industrial production. The high charge density, low-cost fabrication, and less then 25 nm thickness of the diaminonaphthalene-derived films should prove attractive toward practical application on both flat surfaces and in high surface area carbon electrodes.Two-photon lithography (TPL) is an emerging approach to fabricate complex multifunctional micro/nanostructures. This is because TPL can easily develop various 2D and 3D structures on a variety of surfaces, and there has been a rapidly expanding pool of processable photoresists to create different materials. However, challenges in developing two-photon processable photoresists currently impede progress in TPL. In this review, we critically discuss the importance of photoresist formulation in TPL. We begin by evaluating the commercial photoresists to design micro/nanostructures for promising applications in anti-counterfeiting, superomniphobicity, and micromachines with movable parts. Next, we discuss emerging hydrogel/organogel photoresists, focusing on customizing photoresist formulations to fabricate reconfigurable structures that can respond to changes in local pH, solvent, and temperature. We also review the development of metal salt-based photoresists for direct metal writing, whereby various formulations have been developed to enable applications in online sensing, catalysis, and electronics. Finally, we provide a critical outlook and highlight various outstanding challenges in formulating processable photoresists for TPL.Chitin nanofibrils (NCh, ∼10 nm lateral size) were produced under conditions that were less severe compared to those for other biomass-derived nanomaterials and used to formulate high internal phase Pickering emulsions (HIPPEs). Pre-emulsification followed by continuous oil feeding facilitated a "scaffold" with high elasticity, which arrested droplet mobility and coarsening, achieving edible oil-in-water emulsions with internal phase volume fraction as high as 88%. The high stabilization ability of rodlike NCh originated from the restricted coarsening, droplet breakage and coalescence upon emulsion formation. This was the result of (a) irreversible adsorption at the interface (wettability measurements by the captive bubble method) and (b) structuring in highly interconnected fibrillar networks in the continuous phase (rheology, cryo-SEM, and fluorescent microscopies). Because the surface energy of NCh can be tailored by pH (protonation of surface amino groups), emulsion formation was found to be pH-dependent. Emulsions produced at pH from 3 to 5 were most stable (at least for 3 weeks). Although at a higher pH NCh was dispersible and the three-phase contact angle indicated better interfacial wettability to the oil phase, the lower interdroplet repulsion caused coarsening at high oil loading. We further show the existence of a trade-off between NCh axial aspect and minimum NCh concentration to stabilize 88% oil-in-water HIPPEs only 0.038 wt % (based on emulsion mass) NCh of high axial aspect was required compared to 0.064 wt % for the shorter one. The as-produced HIPPEs were easily textured by taking advantage of their elastic behavior and resilience to compositional changes. Hence, chitin-based HIPPEs were demonstrated as emulgel inks suitable for 3D printing (millimeter definition) via direct ink writing, e.g., for edible functional foods and ultralight solid foams displaying highly interconnected pores and for potential cell culturing applications.Graphene has been applied to thermal technology including boiling and condensation heat transfer, from which the pool boiling enhancement relies on adjusting the surface morphology and wettability that is favorable to catalyze the vaporization on the fluid/graphene interface. However, previous works using graphene or reduced graphene oxide (RGO) flake coatings, where the morphology of graphene coating is nonuniform and most of the underlying structured cavities are sealed by graphene flakes. For a long time, this hampered the unraveling of the mechanism behind the enhanced boiling performance by graphene coatings. Moreover, the previous work relied on using water-based pool boiling, which limits the scope of its practical applications since the versatile nonpolar refrigerant has been widely used in boiling heat transfer. The pool boiling was carried out on a plain copper surface to study the effect of fluorinated graphene (F-graphene) coating using nonpolar refrigerant R-141b as the working fluid along with bubble dynamic visualization. It was found that the increase of contact angle leads to more active cavities and enhances heat transfer performance up to twice as much, by applying the F-graphene coating. mTOR inhibitor Moreover, the mechanism of graphene-enhanced heat transfer performance was unraveled and mainly attributed to the hydrophobic surface and effective cavity structure. This research provides a practical and reliable route for enhancing the heat transfer through F-graphene-coatings, which paves the way for potential application in graphene-based thermal technologies.Gallium-based liquid metals are applied in the fabrication of soft electronics because of their conductivity and flexibility. However, the large surface tension and weak adhesion of liquid metals limit the available printing substrates. Recent researches indicate that amalgamating metal particles can turn liquid metal from fluid into a paste which has superb electrical conductivity, plasticity, and strong adhesion to substrates. In this work, a recoverable liquid metal paste was made by mixing eutectic Ga-In alloy and nonmetallic SiO2 (quartz) particles (Ga-In-SiO2 paste, called GIS). GIS has excellent conductivity and printable properties similar to those of previously reported liquid metal pastes. Furthermore, the bonding between Ga-In alloy and quartz particles is reversible. In acidic or alkaline solution, Ga-In alloy can be separated from quartz particles and agglomerated to bulk by stirring. Moreover, the study of the mechanism of adhesion behavior suggests that extruding fresh liquid metal droplets to form more oxide and shearing friction are the critical factors for adhesion.