Hartmanmendoza3890

Nitrous oxide (N2O), a strong greenhouse and ozone depleting gas, is known to be generated in the river environment. However, the impact of sewage treated water on the production mechanism has not been clarified. In this study, N2O production in the upper reach of a river was evaluated by field survey and activity test. The results demonstrated that the N2O production activity of the river pebbles increased with the inflow of the sewage treated water, which was supported by field survey results, such as the dissolved N2O concentrations and water quality. The emission factors of N2O were determined to be 0.02-0.05% in nitrification and 0.01-0.025% in denitrification. Our study shows that combining a field survey and an activity test improves the reliability of the results and leads to the appropriate quantitative evaluation. From a perspective of controlling the N2O emissions from the sewage treatment plant, N2O generation inside the plant is critical. PHTPP datasheet However, appropriate nitrogen removal in the treatment plant is connected to the reduction of N2O generation in the river environment.Pressurized oxy-combustion is an emerging and more efficient technology for carbon capture, utilization, and storage than the first generation (atmospheric) oxy-combustion. NOx is a major conventional pollutant produced in pressurized oxy-combustion. In pressurized oxy-combustion, the utilization of latent heat from moisture and removal of acid gases (NOx and SOx) are mainly conducted in an integrated direct-contact wash column. Recent studies have shown that NOx particular inlet concentration should be maintained before direct contact wash column to remove NOx and SOx efficiently. As a result, minimizing NOx for environmental reasons, avoiding corrosion in carbon capture, utilization, and storage, and achieving effective NOx and SOx removal in direct contact wash columns are crucial. Reburning is a capable and affordable technology for NOx reduction; however, this process is still less studied at elevated pressure, particularly in pressurized oxy-combustion. In this paper, the kinetic evaluation and optimizas from 1 atm to 15 atm. At the higher pressure, the NO reduction rises prominently when the ratio of CH4/NO increases from 1 to 2; however, the effect fades after that. At higher pressure, the NO reduction by CH4 reburning decreases as the H2O concentration increases from 0 to 35%. The optimum equivalence ratio and high pressure for maximum NO reduction are 1.5 and 10 atm, respectively. This study could provide guidance for designing and optimizing a pressurized reburning process for NOx reduction in POC systems.The feasibility of catalytic wet air oxidation, intensified homogeneous Fenton and heterogeneous Photo-Fenton systems for the treatment of real hospital wastewater has been investigated. Wastewater samples were collected from a hospital sewer, during a weekly monitoring program, and fully characterized. Up to seventy-nine pharmaceuticals, including mostly parent compounds and some of their transformation products, were analyzed. Catalytic wet air oxidation allowed the complete removal of several pharmaceutical groups, but it did not allow to eliminate analgesics/anti-inflammatories and antibiotics, whose average removal was around 85%. Intensified Fenton oxidation was the most efficient process for all the drugs removal with an almost complete reduction of the initial pharmaceutical load (99.8%). The heterogeneous Photo-Fenton system reached a 94.5% reduction of the initial pharmaceutical load. The environmental risk of the treated samples by the hazard quotient (HQ) method was also evaluated. Fenton oxidation was the most effective system with a final ∑HQ of 5.4. Catalytic wet air oxidation and Photo-Fenton systems achieved total ∑HQ values of 895 and 88, respectively. This fact was related to the presence of refractory antibiotics in the treated catalytic wet air oxidation samples. On the opposite, the Photo-Fenton system provided the elimination of most pharmaceutical pollutants that pose a high environmental risk such as antibiotics. Simplified cost estimation was finally performed as a preliminary approach of the economy of the three oxidation processes for the hospital wastewater treatment.The proliferation of ever-larger wind turbines poses risks to wildlife, especially from avian collision, yet avoidance behaviour of large-bodied, long-lived bird species in relation to wind turbines remains little studied away from collision "black spots" and offshore marine environments. Here, three-dimensional flight trajectory data are reported from a laser range-finder study of local movements of large-bodied birds (e.g. swans, geese, gulls, cormorants, raptors and cranes, whose populations are relatively more demographically sensitive to collision mortality) in relation to seven terrestrial 150-222 m high (mean 182 m) wind turbines constructed in Denmark in a N-S line. Comparisons of two-dimensional flight passages between turbines pre- (n = 287) and post-construction (n = 1210) showed significant (P 182 m) were significantly greater (P less then 0.0001) post-construction than prior to construction. These are the first results from tracking large-bodied bird flight trajectories to show the magnitude of their vertical and horizontal adjustments to the presence of turbines, which have implications for assumptions of even flight densities made by collision risk models currently used to predict avian turbine collision rates.Serious heavy metals pollution was characterized in the lead/zinc mine tailings dam and surrounding soils, as well as copper slag disposal sites. This study investigates the efficacy of modified granulated copper slag (MGCS) as a partial replacement of ordinary Portland cement (OPC) for lead/zinc mine tailings-based cemented paste backfill (CPB) application using Na2SO4 (CSN) and CaO (CSC) as alkali-activated materials. The effect of different scenarios was ascertained by unconfined compressive strength (UCS). Also, the correlated microstructural evolution and mineralogical phase generation were obtained by scanning electron microscopy (SEM), mercury intrusion porosimetry (MIP), and X-ray diffraction (XRD). The main findings proved that CSN was more effective in improving mechanical performance. Na2SO4 was found associated with C-S-H gel formation accompanied by a compact microstructure and better pore distribution with lower porosity. However, deposition of chloride compound was found in the surface layer of CSN samples, which could bring deterioration to the mechanical properties.