Abildgaardbuckner2368

be adsorption-interparticle bridging brought about by their flake-like structures and surfaces charges. Varying pH had no measurable influence on the coagulation performance of the KCPs. Comparing their efficiency with MoringaOleifera (MO, a previously researched PCP) and alum showed that HxKP had a negligibly different particle removal as MO. StKP turbidity removal performance was below HxKP by 1% for HTW and LTW and 2% for MTW but performed higher than the CrKP by 5% and 7% in HTW and MTW, respectively. The optimum dosage of HxKP and StKP reduced DBP surrogate values, indicating that its precursor is also minimized, although a slight shift from this optimum dosage showed a significant rise in their concentration thus signifying a potential increase in DBPs during disinfection.Sediments have been found to be one of the most important reservoirs for microplastics, providing abundant indigenous microbes. The processes involved in the distribution and degradation behavior of microplastics are complex. This study investigated the vertical distribution of microplastics (with the size less then 5 mm) and the bacterial community assemblages colonizing microplastics in urban river sediments at a depth from 0 to 50 cm. The results showed that both microplastics and associated microbial communities presented vertical profiles in river sediments. The mean concentration of microplastics increased from the shallow layers to the deep layers of sediments, and smaller microplastic particles were dominant in deeper layers. A greater degradation of microplastics in deeper layers was confirmed by contact angle measurements, scanning electron microscopy and Fourier transform infrared spectroscopy-attenuated total reflectance analyses. Unlike the surrounding sediments, the whole bacterial communitiesigrate into groundwater.Reverse osmosis (RO) seawater desalination is a widely applied technological process to supply potable water worldwide. Recently, saline groundwater (SGW) pumped from beach wells in coastal aquifers that penetrate beneath the freshwater-seawater interface is considered as a better alternative water source to RO seawater desalination as it is naturally filtered within the sediments which reduces membrane fouling and pre-treatment costs. The SGW of many coastal aquifers is anoxic - and thus, in a low redox stage - has elevated concentrations of dissolved manganese, iron and sulfides. We studied the influence of the SGW redox stage and chemistry on the performance - permeate flux and fouling properties - of RO desalination process. SGWs from three different coastal aquifers were sampled and characterized chemically, and RO desalination experiments were performed under inert and oxidized conditions. Our results show that all three aquifers have anoxic saline groundwater and two of them have intensive anaerobic oxidation of organic matter. Two aquifers were found to be in the denitrification stage or slightly lower and the third one in the sulfate reduction stage. Our results indicate that the natural redox stage of SGWs from coastal aquifers affects the performance of RO desalination. All SGW types showed better RO performance over seawater desalination. Furthermore, air oxidation of the SGW was accompanied with pH elevation, which increased the membrane fouling. Hence, keeping the feed water unexposed to atmospheric conditions for maintaining the natural reducing stage of the SGW is crucial for low fouling potential. The observed benefits of using naturally reduced SGW in RO desalination have significant implications for reduction in overall process costs.Over the past decade, 3D printing or additive manufacturing (AM) technology has seen great advancement in many aspects such as printing resolution, speed and cost. Membranes for water treatment experienced significant breakthroughs owing to the unique benefits of additive manufacturing. In particular, 3D printing's high degree of freedom in various aspects such as material and prototype design has helped to fabricate innovative spacers and membranes. However, there were conflicting reports on the feasibility of 3D printing, especially for membranes. Some research groups stated that technology limitations today made it impossible to 3D print membranes, but others showed that it was possible by successfully fabricating prototypes. This paper will provide a critical and comprehensive discussion on 3D printing specifically for spacers and membranes. Camostat solubility dmso Various 3D printing techniques will be introduced, and their suitability for membrane and spacer fabrication will be discussed. It will be followed by a review of past studies associated with 3D-printed spacers and membranes. A new category of additive manufacturing in the membrane water industry will be introduced here, known as hybrid additive manufacturing, to address the controversies of 3D printing for membrane. As AM technology continues to advance, its possibilities in the water treatment is limitless. Some insightful future trends will be provided at the end of the paper.We analyzed mid- to long-term 137Cs wash-off from the catchments contaminated due to the Chernobyl accident in 1986 and the Fukushima Dai-ichi Nuclear Power Plant accident in 2011. A semi-empirical diffusional model for radionuclide wash-off is proposed to enable estimation of the dissolved and particulate 137Cs wash-off ratios for the Chernobyl and Fukushima contaminated catchments; the differences in the wash-off characteristics for these two regions are explained and their long-term trends predicted. The model is based on the premise that the catchment topsoil layer is the source of sediments in the rivers, and the radionuclide concentration in the topsoil can be described by a simple diffusion equation. The particulate 137Cs wash-off ratios for the Fukushima contaminated catchments appear to be comparable or slightly lower than those for Chernobyl. The dissolved 137Cs wash-off ratios for Fukushima catchments are at least an order of magnitude lower than those for Chernobyl, mainly due to an order of magnitude difference in the 137Cs distribution coefficients for the Fukushima and Chernobyl rivers. The proposed semi-empirical diffusional model for radionuclide wash-off satisfactorily describes the temporal trends in the 137Cs wash-off characteristics for both the Chernobyl and Fukushima cases, and can be used as a tool for predicting 137Cs wash-off after a nuclear accident.