Krygerenevoldsen3873

Titanium tetrachloride (TiCl₄) as an alternative coagulant to remove organic matters and nutrients from the effluent of the secondary wastewater treatment was evaluated by comparison of removal efficiency of total phosphorous to Al- and Fe-based coagulants. Also, the surface characteristics, elemental contents, and crystallinity of the TiO₂ produced from wastewater sludge flocculated with TiCl₄ coagulant were investigated depending on the calcination temperatures. The more dosages of coagulants were injected, the greater concentrations of the cations (Al+3, Fe+3, Ti+4) and hydrogen ions (H+) resulted in the lower pH. Also, TiCl₄ formed larger and heavier flocs than other coagulants and resulted in greater T-P removal efficiencies with reduced amounts of dosage. The phase change of anatase and rutile crystalline structures of TiO₂ incinerated from wastewater sludges of TiCl₄ coagulant was observed at relatively high calcination temperatures due to the existence of mixtures of organic matters, nutrients, and various impurities in the wastewater sludges of TiCl₄ coagulant. Both C and P atoms were found to be mainly doped in/on TiO₂ and the C and P atom originated from residual carbon of the settled organic matters and phosphorus nutrients present in effluents from sewage treatment plant, respectively. Therefore, 600-800 °C is the optimal calcination temperatures for TiO₂ produced from TiCl₄ coagulant flocculated with effluents from sewage treatment plant.The complete oxidation of toluene (as a model volatile organic compound) was studied to determine the influence of adding a transition metal (Mn, Cr, Fe, Co, and Ni) to the 5 Cu/Al catalyst. The physcochemical properties of the catalysts were characterized by Brunauer-Emmett-Teller (BET) surface area analysis, X-ray diffraction (XRD) analysis, field emission transmission electron microscopy (FE/TEM), and hydrogen temperature programmed reduction (H₂-TPR). The catalytic activity of the supported bimetallic catalysts followed the order 5Cu-5Mn/Al > 5Cu-5Cr/Al > 5Cu-5Fe/Al > 5Cu-5Co/Al > 5Cu > 5Cu-5Ni/Al, based on the temperature for T90 of toluene conversion (T90). Two different reaction mechanisms (mixing and the synergistic effect) were operative in the supported bimetallic catalysts except for the 5Cu-5Mn/Al and 5Cu-5Ni/Al catalysts, on the basis of the reaction temperature. The difference between the electronegativity of copper and the added transition metal was associated with the catalytic activity.Activated carbon fiber (ACF) is widely used as an adsorption fiber in air purification systems. In this study, MgO and CuO nanoparticles were immobilized on ACF with enhancement of (3-aminopropyl)triethoxysilane (APTES). The obtained fibers' coating efficiency, structural deformation, and antimicrobial activities were investigated. The MgO-CuO/APTES/ACF fiber (DA-MC) sample showed high antimicrobial activity ( less then 90%) against both Escherichia coli and Staphylococcus aureus after 24-hour treatment. DA-MC also showed the highest coating efficiency, with no observed structural deformation. The presence of APTES and curing step at high temperature is believed to increase the coating efficiency and thus result in the high antimicrobial activity and also protect the ACF from deformation.The purpose of this study is to investigate the surface activity of starch nanocrystals (SNC), material derived from starch, and confirm their usefulness as a surfactant. In order to evaluate the surface activity, the surface tension change of suspended SNC solution via the Wilhelmy plate method was measured and the values were compared with various synthetic surfactants. The effect of SNC as emulsifier was evaluated on emulsion formation and physical stability. Rilematovir molecular weight The surface tension of the SNC-dispersed solution was decreased while its concentration was increased. When the 5.0% (w/v) of SNC was added, the surface tension was decreased from 70.3 to 49.5 mN/m. It was confirmed that the physical stability of the emulsion prepared by adding the SNC was improved compared to that of surface inactivity material (PEG 400). The phase separation was observed within 1 hour after preparation of the emulsion containing PEG 400, but the emulsion containing SNC was stable for 5 hours or more. To summarize this study, SNC, a natural-derived and non-toxic material, exhibits sufficient surface activity, thereby confirming the possibility of being applied to the food and pharmaceutical industry.Self-assembled nano-layering resulting from interaction of the phosphate functional group of adhesive monomers with zirconia ceramic surface has been proposed. The purpose of this study was to investigate the bond strengths of two adhesive resin cements (Panavia F 2.0 and BisCem) containing phosphate monomers added with various concentrations (0.0, 1.0, 3.0, and 5.0 wt%) of triethylene glycol dimethacrylate (TEGDMA) to air-abraded zirconia ceramic. The polished/air-abraded zirconia plates (KaVo Everest® ZS-Ronde) were imaged using atomic force microscopy and the average surface roughness (Ra) values were calculated (n = 5). The surface energy parameters of the zirconia plates and the resin cements were calculated based on the extended Fowkes theory. All resin-bonded (diameter 2.38 mm) zirconia specimens were stored in water at 37 °C for 24 h and then half of them additionally thermocycled 10,000 times before the shear bond strength (SBS) test (n = 10). Air-abrasion of zirconia surface significantly increased the γhS (hydrogen bonding component) value (p less then 0.001), as well as greatly increasing the surface area (p less then 0.001). For both resin cements, the γhS (dipole-dipole component) gradually increased with increasing incorporated TEGDMA concentrations, whereas the γhS gradually decreased. Overall, the addition of 3.0 wt% of TEGDMA consistently resulted in higher SBS values even after thermocycling. Under the tested condition, reducing the concentration of the adhesive monomers with phosphate functional group by adding the dimethacrylate monomer (up to 3.0 wt%) increased the bond strength between the resin cements and zirconia ceramic.