Barnettmortensen4596

05).

The failure and success rates were not significantly influenced by cement thickness (P = 0.137 and P = 0.872, respectively); thus, the null hypothesis was accepted. However, when log-rank test for trends was applied to failure events, the tendency to have less failures with increasing thicknesses was found statistically significant (P = 0.047).

The cement thickness within the range adopted here did not have a significant effect on the failure or success rate of lithium disilicate occlusal veneers when exposed to randomized impact stresses generating fatigue phenomena.

The cement thickness within the range adopted here did not have a significant effect on the failure or success rate of lithium disilicate occlusal veneers when exposed to randomized impact stresses generating fatigue phenomena.

Removable dentures are a reasonable option for prosthetic treatment. However, continuous residual ridge resorption and reline procedures are inevitable owing to the strong pressure exerted on the mucosa or inappropriate pressure distribution. This study aimed to elucidate the association between the gonial angle on orthopantomogram (GAO) with occlusal force and reline frequency in removable partial denture wearers.

Participants were patients who had previously received removable partial denture treatment for a free-end defect. Age, sex, number of remaining teeth, remaining opposing teeth, and occlusal support were investigated. GAO was measured using panoramic radiographs. The mean relining interval was calculated as the mean number of days between denture insertion and the first relining or subsequent relining. The association between the mean relining interval and each factor was investigated.

Sixty-five subjects (33 females) were analyzed. The median value of the mean relining interval was 533.3 days, and the median GAO was 123º. There was a significant positive correlation between the mean relining interval and GAO (rs = 0.335). The number of remaining opposing teeth and occlusal support exhibited weak negative correlations with mean relining interval (rs = -0.187 and -0.214, respectively). Multivariate analysis using a generalized linear model showed that GAO was a significant explanatory variable for the m ean relining interval.

Within the limitations of this study, GAO was found GAO was found to contribute to the increased frequency of relining due to ridge resorption in patients with a small GAO.

Within the limitations of this study, GAO was found GAO was found to contribute to the increased frequency of relining due to ridge resorption in patients with a small GAO.

This study aims to evaluate the effects of cement shade, restorative material type, and thickness on the final color of resin-matrix ceramics.

Ninety A2 shade resin-matrix ceramic specimens were prepared from Vita Enamic, GC Cerasmart, and Lava Ultimate at 0.5 and 1.0 mm thicknesses. Sixty resin cement disks were fabricated from different shades (A1, A3O, B05, and TR) of RelyX Ultimate at 0.1 mm thickness. CIE color coordinates were measured using a spectrophotometer, and color differences (∆ E 00 ) were calculated. Data were statistically analyzed (P =0.05).

The ΔE 00 values were influenced by the cement shade, restorative material type, thickness, and their interactions ( P < 0.05). A3O cement caused clinically unacceptable values for all groups at 0.5 mm thickness and GC at 1.0 mm thickness. A1 and TR cement shades demonstrated visually perceptible but clinically acceptable values, except for VE-A1 and LU-A1 at 0.5 mm thickness. Src inhibitor The ∆E 00 values of the B05 cement shade were lower than the visually perceptible threshold for both thicknesses except for GC at 0.5 mm thickness.

The shade of the resin cement and the type and thickness of the resin-matrix ceramic material significantly affected the resulting final color. To provide a shade matching with natural dentition and to obtain esthetic restorations, especially for the anterior teeth, the resin cement shade and resin-matrix ceramic material should be carefully selected.

The shade of the resin cement and the type and thickness of the resin-matrix ceramic material significantly affected the resulting final color. To provide a shade matching with natural dentition and to obtain esthetic restorations, especially for the anterior teeth, the resin cement shade and resin-matrix ceramic material should be carefully selected.

To evaluate the effect of three different designs and two monolithic ceramic materials on the durability and fracture resistance of endocrowns on maxillary first premolars, in comparison to post-and-core crowns.

Fifty-six maxillary premolars were endodontically treated and shortened to a level of 2 mm from the cervical line, and randomly categorized into six endocrown groups and post-and-core crown control group (n=8); E1; endocrowns with flat occlusal table (without ferrule), E2; endocrowns with 1.5 mm circumferential ferrule, E3; endocrowns with 1.5 mm buccal ferrule preparation. Two materials were used for endocrowns zirconia (4YSZ; Z), and lithium disilicate (L). The control group was restored with zirconia posts, and lithium disilicate crowns. All restorations were bonded using Panavia V5 and its respective primers and underwent thermo-mechanical fatigue with a 10 kg dynamic load for 1,200,000 cycles and thermocycling between 5 and 55 °C. Thereafter all survived specimens were loaded to fracture. The results were statistically analyzed using ANOVA and T-Test.

None of the specimens showed any signs of debonding or fracture caused by the fatigue test. The PC control group showed no statistically significant difference in comparison to groups ZE1, ZE2 and LE2 ( p > 0.05 ). However, it was significantly different from groups LE1, LE3, and ZE3 ( p ≤ 0.05 ).

Preparation designs and materials affected the fracture resistance of endocrowns. The results showed a superiority of the post-and-core crowns,zirconia/lithium disilicate endocrowns with 1.5 mm circumferential ferrule, and zirconia endocrowns with the flat occlusal table.

Preparation designs and materials affected the fracture resistance of endocrowns. The results showed a superiority of the post-and-core crowns,zirconia/lithium disilicate endocrowns with 1.5 mm circumferential ferrule, and zirconia endocrowns with the flat occlusal table.