Kempkessler3751

Autowatch Ghost Immobiliser Installation

The Ghost is the UK’s most advanced aftermarket immobiliser for CAN buses. It is discrete and does not have LED indicators or key fobs, and is hidden within the wiring of the vehicle.

It also allows the user to disable the system temporarily through Transport Mode to use it when they are renting out their vehicle. This guide will walk you through the installation process of the Ghost immobiliser.

Professional Installation

The Autowatch Ghost immobiliser is a advanced security device that safeguards your vehicle against hacking, key cloning, and relay attacks. cost of ghost immobiliser is directly connected to the ECU of your car and protected by a PIN code you select. It's inaccessible to thieves using diagnostic scanners or other modern methods, and is unable to be disabled by circuit cuts.

The system is easy to use, but professional installation is recommended to ensure a smooth connection to the ECU of your vehicle. Installers who are approved by Thatcham can assist with the installation and programming of your Ghost system. They can also recommend an alarm or tracking system to complete the protection package for your vehicle.

To prevent an accidental deployment of short circuits or airbags The installer must first disconnect your battery. After the battery has been disconnected, the installer can be able to work safely. Basic hand tools are useful to make precise connections and a multimeter may be used to test the electrical properties and safety. Insulation tape and cable ties are also essential for protecting connections and keeping wiring tidy. The Ghost Immobiliser user manual will provide specific instructions specifically tailored to your specific model.

It is crucial to select an area for grounding that is free of dirt or paint during installation. The installer must ensure that the immobiliser's CAN H as well as CAN L wires are connected to the appropriate ports on your vehicle's ECU. Based on the model, these wires might need to be soldered or plugged into. A top-quality connector is recommended to ensure a durable and secure connection.

After the installation is completed Once the installation is completed, the customer can enable after the installation is complete, the customer can activate Transport Mode. This allows the vehicle to be utilized by valet parking companies or mechanics without having to know the pin code. The customer has to press the icon for service on the dashboard five times in two seconds. Once this is done, the system will confirm by displaying 5 signals.

The Autowatch Ghost 2 is a highly efficient immobiliser that's TASSA verified and Thatcham approved. It's a smart option for those who regularly rents out their cars on platforms such as Turo. Immobilisers can also lower insurance costs since it significantly decreases the risk of theft.

Getting Started

You can't go far wrong using an autowatch immobiliser if you want to protect your car from theft. It prevents your car from running even if someone steals or copies your key. It is possible because of its advanced technology that stops the engine from starting until the correct PIN code is entered.

The device connects to the vehicle's bus network CAN which allows direct communication with the ECU. It uses the buttons on your dashboard and steering wheel to create a unique sequence, which only you are aware of. This makes it impossible for anyone else to start your vehicle. This is the ultimate security system that protects your most precious possessions and preserve its value in the event that you decide to sell it in the future.

Installing a ghost ignition is an easy process, however, it's important to follow the instructions carefully to avoid electrical issues and system malfunctions. You'll need to locate a power supply of 12V and a solid grounding on the car's chassis. Then, you can begin to connect the wires for the immobiliser. Be sure to use high-quality connectors and soldering techniques to ensure a secure connection. Make sure to shield the connections with heat shrink tubing or insulation tape, as well as other materials to avoid electrical short circuits.

After the wires have been connected, you can connect the battery and turn on the engine to test the immobiliser's functionality. Once you have verified that everything is working properly, you can install the immobiliser in a safe position inside the vehicle. Make sure you hide it in a secure manner to prevent any thief from taking advantage of it.

The Ghost 2 immobiliser is TASSA (Tracker and Aftermarket Security System Association) verified This means it meets the highest standards of security and is a fantastic deterrent to car thieves. It provides superior protection against key cloning, hacking, and relay attacks. It cannot be disabled without knowing the code. The device is simple to use, and can be set into the service valet setting to ensure that your vehicle will not be activated if you bring it for an MOT or servicing.

Wiring

The Ghost Immobiliser is a cutting-edge security system that is designed to stop theft of vehicles. It communicates with your vehicle's ECU and connects directly to the CAN bus. Ghost Immobiliser doesn't interfere with your vehicle's factory settings, unlike other aftermarket systems which require the removal of circuit elements.

It's also totally undetectable by thieves using diagnostic scanning devices. This is due to the fact that it does not transmit and receive radio frequency signals and it utilizes CAN data to communicate with your ECU. In addition, it doesn't need any modifications to your vehicle's existing key fobs.

Enter your sequence for disarming (either two or one buttons) and turn on the ignition of your car to use Ghost Immobiliser. The indicator will flash two times to confirm that you've entered the correct code. After this, you can start your vehicle and drive off with peace of mind.





Once installed, the Ghost Immobiliser safeguards your vehicle against hacking or key cloning, while protecting its value. If you ever have to surrender your car for service or valet parking, the Ghost Immobiliser can be temporarily disabled in Transport Mode.

To complete a Ghost Immobiliser installation, you'll have to locate an energy source that is constant (12V) and a grounding point. Make sure both are properly insulated and can be touched. It is also recommended to use cable tie to secure and bundle the wires. This will decrease the chance of theft by thieves. To avoid mistakes, double-check these points and mark them with labels or tape. Verify all connections for signs they're wearing out. Make sure that all connections are firmly in place and properly insulated. Also, don't forget test the Ghost Immobiliser after the installation is completed. This will confirm that the unit is working correctly and that all connections and insulation are secure. Be sure to correct any problems immediately.

Testing

The Autowatch Ghost immobiliser is an innovative vehicle security system that connects seamlessly with your car's ECU in order to prevent unauthorised motor starting. Its cutting-edge technology protects your vehicle against hacking and key cloning along with other methods used by thieves to steal cars. The Ghost is also able to work in conjunction with existing alarm and tracking systems to give the ultimate vehicle protection. The Ghost's unique features and subtle design make it a popular choice for car enthusiasts and security-conscious motorists alike.

It is important to follow the steps of installation in order to ensure a proper integration of Ghost Immobiliser. Consult the wiring diagram for the vehicle to assist you in locating and connecting the wires. You'll then need to identify the power and grounding sources. Once you've found them you'll have to mark them in a way that they're easily identifiable when installing. It is also essential to use high-quality tools and materials. Basic hand tools can assist in making connections that are precise and a multimeter can confirm electrical values and guarantee security. Insulation tape and cable tie will keep all connections neat. A Ghost-specific user's guide is also available.

It is essential to test the system prior to installing it. Enter the PIN code into the system and start the vehicle. This test will verify that the immobiliser works as intended and will stop vehicle starts that are not authorized. It is recommended that you perform this procedure regularly as part of your regular vehicle inspections to ensure that the system is operating correctly.

Once the installation has been completed, you are now able to start driving your vehicle with confidence. The Ghost will protect your vehicle from potential car thieves. It will ensure that no one is able to take your car away even if they don't have the correct PIN code. The Ghost can also be paired with a Thatcham-approved tracker to detect any attempt to steal or tamper, allowing you to locate your vehicle in the event of it being stolen.

The Ghost can be used in a variety of vehicles and is compatible with the majority of major brands. Monty's Locksmith can assist you in securing your vehicle with this innovative device. Contact us today to find out more about our service and installation options. We are a TASSA Registered installer This certification ensures that we follow strict standards and procedures for installing our products. This reassures customers, insurers, and law enforcement that all installations are performed safely and in a correct manner.