Bentsensutton8749

In order to develop improved vaccinations against tuberculosis, it is essential to understand the effect of vaccination on the immune response, and to overcome the mechanisms by which mycobacteria regulate this immune response. In this study, we examine the effect of intradermal vaccination with Mycobacterium bovis bacille Calmette-Guèrin on macrophage phenotype following intranasal challenge with virulent Mycobacterium bovis. Preserved lung tissues used in the present study were obtained from a previous vaccination trial in BALB/c mice. Vaccinated mice showed less extensive pulmonary lesions along with a significant decrease in bacterial lung burden when compared to control mice. Immunohistochemical markers of classically activated macrophages (iNOS) and alternatively activated macrophages (Arg1, FIZZ1) were applied to lung sections. Vaccination led to a statistically significant decrease in the number of Arg1+ macrophages. The presence of macrophages that expressed Arginase 1 in pulmonary lesions was much smaller than the presence of macrophages expressing iNOS. learn more The low presence of Arg1+ macrophages induced by vaccination may be caused by Th1 polarization and may reduce alternative activation of macrophages, with an overall more effective intracellular killing of bacteria.Objective The aim of this study was to develop bioactive and osseointegrable polyetheretherketone (PEEK)-based composite filaments melt-blended with novel amorphous magnesium phosphate (AMP) particles for 3D printing of dental and orthopedic implants. Materials and methods A series of materials and biological analyses of AMP-PEEK were performed. Thermal stability, thermogravimetric and differential scanning calorimetry curves of as-synthesized AMP were measured. Complex viscosity, elastic modulus and viscous modulus were determined using a rotational rheometer. In vitro bioactivity was analyzed using SBF immersion method. SEM, EDS and XRD were used to study the apatite-forming ability of the AMP-PEEK filaments. Mouse pre-osteoblasts (MC3T3-E1) were cultured and analyzed for cell viability, proliferation and gene expression. For in vivo analyses, bare PEEK was used as the control and 15AMP-PEEK was chosen based on its in vitro cell-related results. After 4 or 12 weeks, animals were euthanized, and the femurs were collected for micro-computed tomography (μ-CT) and histology. Results The collected findings confirmed the homogeneous dispersion of AMP particles within the PEEK matrix with no phase degradation. Rheological studies demonstrated that AMP-PEEK composites are good candidates for 3D printing by exhibiting high zero-shear and low infinite-shear viscosities. In vitro results revealed enhanced bioactivity and superior pre-osteoblast cell function in the case of AMP-PEEK composites as compared to bare PEEK. In vivo analyses further corroborated the enhanced osseointegration capacity for AMP-PEEK implants. Significance Collectively, the present investigation demonstrated that AMP-PEEK composite filaments can serve as feedstock for 3D printing of orthopedic and dental implants due to enhanced bioactivity and osseointegration capacity.Objective To investigate the clinical behavior of two different resin-based restorative systems in extended Class II cavities in a controlled prospective split-mouth study over 12 years and to assess marginal quality under a SEM using epoxy replicas. Methods Thirty patients received 68 resin composite restorations (Solobond M+Grandio n=36; Syntac+Tetric Ceram n=32) by one dentist in a private practice. 35% of cavities revealed no enamel at the bottom of the proximal box, 48% of cavities provided less then 0.5mm remaining proximal enamel. Restorations were examined according to modified USPHS criteria at baseline, and after six months, one, two, four, six, eight, 10, and 12 years. Expoxy replicas of 21 restoration pairs were analysed under a SEM at 200× magnification regarding marginal quality. Results At the 12-years recall, 59 of the original 68 restorations in 27 of 30 patients were available (drop out 13%). Two restorations failed due to cusp fracture (Tetric Ceram) and marginal fracture (Grandio). The overall success rate of all restorations was 97.1% (Kaplan-Meier survival algorithm) with no differences between the two materials (p=0.923). After 144 months of clinical service, restorations in molars performed worse than in premolars regarding the integrity of restoration and tooth (p less then 0.05) being detected as wear, chippings, and cracks. Beyond the 4-year recall, marginal staining significantly increased. SEM evaluation of replicas revealed that perfect margin (49% baseline vs. 10% after 12 years), overhang (13% at baseline vs. 3% after 12 years), negative step formation (34% at baseline vs. 75% after 12 years), and marginal fractures (0% at baseline vs. 6% after 12 years) significantly changed during the evaluation period (p less then 0.001). Significance Extended direct resin composite restorations performed satisfactorily over 12 years of clinical service. SEM analysis delivered qualitative data regarding marginal deterioration over time.Introduction This study aimed to evaluate the morphologic and positional features of the mandible in children, adolescents, and adults with skeletal Class I and unilateral posterior crossbite. Methods The sample included cone-beam computerized tomography images of 76 subjects, divided in 3 groups (1) children (aged 6.77 ± 1.5 years; n = 25), (2) adolescents (aged 14.3 ± 1.7 years; n = 26), and (3) adults (aged 32.66 ± 13.4 years; n = 25) with unilateral posterior crossbite. Condylar and mandibular linear distances and angles were performed using a mirrored 3-dimensional overlapped model. Intragroup asymmetries were determined by a comparison between crossbite and no crossbite sides. The differences between both sides of all measurements were compared among groups and correlated to mandibular horizontal rotation (yaw) and age. Results The crossbite side showed shorter distances in the condyle and mandibular regions. Asymmetries were slightly but significantly greater in adults, as expressed by the lateromedial condylar distance, total ramus height, and mandibular length with an average 0.