Tatedaugherty0214

Thus, these results suggest that mitigating SOX9 resistance to KEAP1-mediated degradation can represent a novel therapeutic strategy for cancers with KEAP1 mutations.Epitaxial growth of III-nitrides on 2D materials enables the realization of flexible optoelectronic devices for next-generation wearable applications. Unfortunately, it is difficult to obtain high-quality III-nitride epilayers on 2D materials such as hexagonal BN (h-BN) due to different atom hybridizations. Here, the epitaxy of single-crystalline GaN films on the chemically activated h-BN/Al2O3 substrates is reported, paying attention to interface atomic configuration. It is found that chemical-activated h-BN provides B-O-N and N-O bonds, where the latter ones act as effective artificial dangling bonds for following GaN nucleation, leading to Ga-polar GaN films with a flat surface. The h-BN is also found to be effective in modifying the compressive strain in GaN film and thus improves indium incorporation during the growth of InGaN quantum wells, resulting in the achievement of pure green light-emitting diodes. This work provides an effective way for III-nitrides epitaxy on h-BN and a possible route to overcome the epitaxial bottleneck of high indium content III-nitride light-emitting devices.Inorganic perovskite solar cells (PSCs) have witnessed great progress in recent years due to their superior thermal stability. As a representative, CsPbI2Br is attracting considerable attention as it can balance the high efficiency of CsPbI3 and the stability of CsPbBr3. However, most research employs doped charge transport materials or applies bilayer transport layers to obtain decent performance, which vastly complicates the fabrication process and scarcely satisfies the commercial production requirement. In this work, all-layer-doping-free inorganic CsPbI2Br PSCs using organic ligands armored ZnO as the electron transport materials achieve an encouraging performance of 16.84%, which is one of the highest efficiencies among published works. Meanwhile, both the ZnO-based CsPbI2Br film and device show superior photostability under continuous white light-emitting diode illumination and improved thermal stability under 85 °C. The remarkable enhanced performance arises from the favorable organic ligands (acetate ions) residue in the ZnO film, which not only can conduce to maintain high crystallinity of perovskite, but also passivate traps at the interface through cesium/acetate interactions, thus suppressing the photo- and thermal- induced perovskite degradation.The shuttle effect of soluble lithium polysulfides during the charge/discharge process is the key bottleneck hindering the practical application of lithium-sulfur batteries. Herein, a multifunctional interlayer is developed by growing metallic molybdenum disulfide nanosheets on both outer and inner walls of cotton cloth derived carbon microtube textile (MoS2@CMT). The hollow structure of CMT provides channels to favor electrolyte penetration, Li+ diffusion and restrains polysulfides via physical confinement. The hydrophilic and conductive 1T-MoS2 nanosheets facilitate chemisorption and kinetic behavior of polysulfides. The synergic effect of 1T-MoS2 nanosheets and CMT affords the MoS2@CMT interlayer with an efficient trapping-diffusion-conversion ability toward polysulfides. Therefore, the cell with the MoS2@CMT interlayer exhibits enhanced cycling life (765 mAh g-1 after 500 cycles at 0.5 C) and rate performance (974 mAh g-1 at 2 C and 740 mAh g-1 at 5 C). This study presents a pathway to develop low-cost multifunctional interlayers for advanced lithium-sulfur batteries.It is well-known that the alkali doping of polycrystalline Cu2ZnSn(S,Se)4 (CZTSSe) and Cu(In,Ga)(Se,S)2 has a beneficial influence on the device performance and there are various hypotheses about the principles of performance improvement. This work clearly explains the effect of Na doping on the fill factor (FF) rather than on all of the solar cell parameters (open-circuit voltage, FF, and sometimes short circuit current) for overall performance improvement. When doping is optimized, the fabricated device shows sufficient built-in potential and selects a better carrier transport path by the high potential difference between the intragrains and the grain boundaries. On the other hand, when doping is excessive, the device shows low contact potential difference and FF and selects a worse carrier transport path even though the built-in potential becomes stronger. The fabricated CZTSSe solar cell on a flexible metal foil optimized with a 25 nm thick NaF doping layer achieves an FF of 62.63%, thereby clearly showing the enhancing effect of Na doping.Strong, stretchable, and durable biomaterials with shape memory properties can be useful in different biomedical devices, tissue engineering, and soft robotics. However, it is challenging to combine these features. Semi-crystalline polyvinyl alcohol (PVA) has been used to make hydrogels by conventional methods such as freeze-thaw and chemical crosslinking, but it is formidable to produce strong materials with adjustable properties. Herein, a method to induce crystallinity and produce physically crosslinked PVA hydrogels via applying high-concentration sodium hydroxide into dense PVA polymer is introduced. Such a strategy enables the production of physically crosslinked PVA biomaterial with high mechanical properties, low water content, resistance to injury, and shape memory properties. It is also found that the developed PVA hydrogel can recover 90% of plastic deformation due to extension upon supplying water, providing a strong contraction force sufficiently to lift objects 1100 times more than their weight. Cytocompatibility, antifouling property, hemocompatibility, and biocompatibility are also demonstrated in vitro and in vivo. The fabrication methods of PVA-based catheters, injectable electronics, and microfluidic devices are demonstrated. This gelation approach enables both layer-by-layer and 3D printing fabrications.Coronavirus disease 2019 (COVID-19) is a global pandemic caused by severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2). LY2157299 clinical trial The models that can accurately resemble human-relevant responses to viral infection are lacking. Here, we create a biomimetic human disease model on chip that allows to recapitulate lung injury and immune responses induced by SARS-CoV-2 in vitro at organ level. This human alveolar chip reproduced the key features of alveolar-capillary barrier by co-culture of human alveolar epithelium, microvascular endothelium and circulating immune cells under fluidic flow in normal and disease. Upon SARS-CoV-2 infection, the epithelium exhibited higher susceptibility to virus than endothelium. Transcriptional analyses showed activated innate immune responses in epithelium and cytokine-dependent pathways in endothelium at 3 days post-infection, revealing the distinctive responses in different cell types. Notably, viral infection caused the immune cell recruitment, endothelium detachment, and increased inflammatory cytokines release, suggesting the crucial role of immune cells involving in alveolar barrier injury and exacerbated inflammation.