Rousefyhn0176

The use of this methodology based on the Auger parameter is neither trivial nor ordinary. We demonstrate its validity since the different values of this parameter allow to identify the oxidation state of silver and consequently to evaluate the formation yield of metallic Ag NPs in the HA-FCC matrix and the effectiveness of the different reduction methods used.In this paper we report the crystal growth conditions and optical anisotropy properties of Tungsten ditelluride (WTe2) single crystals. The chemical vapor transport (CVT) method was used for the synthesis of large WTe2 crystals with high crystallinity and surface quality. These were structurally and morphologically characterized by means of X-ray diffraction, optical profilometry and Raman spectroscopy. Through spectroscopic ellipsometry analysis, based on the Tauc-Lorentz model, we identified a high refractive index value (~4) and distinct tri-axial anisotropic behavior of the optical constants, which opens prospects for surface plasmon activity, revealed by the dielectric function. The anisotropic physical nature of WTe2 shows practical potential for low-loss light modulation at the 2D nanoscale level.In the present study, a buckling analysis of laminated composite rectangular plates reinforced with multiwalled carbon nanotube (MWCNT) inclusions is carried out using the finite element method (FEM). The rule of mixtures and the Halpin-Tsai model are employed to calculate the elastic modulus of the nanocomposite matrix. The effects of three critical factors, including random dispersion, waviness, and agglomeration of MWCNTs in the polymer matrix, on the material properties of the nanocomposite are analyzed. Then, the critical buckling loads of the composite plates are numerically determined for different design parameters, such as plate side-to-thickness ratio, elastic modulus ratio, boundary conditions, layup schemes, and fiber orientation angles. The influence of carbon nanotube fillers on the critical buckling load of a nanocomposite rectangular plate, considering the modified Halpin-Tsai micromechanical model, is demonstrated. The results are in good agreement with experimental and other theoretical data available in the open literature.Control over both dispersion and the particle size distribution of supported metal particles is of paramount importance for the catalytic activity of composite materials. We describe the synthesis of materials with Cu nanoparticles well-dispersed on different amine-functionalized supports, using the extract of Wallich Spurge as a green, reducing agent. Graphene oxide (GO), mesoporous silica (MCM-41), mesoporous zirconia, and reduced graphene oxide-mesoporous silica (RGO-MCM-41) were explored as supports. Cu nanoparticles were better stabilized on RGO-MCM-41 compared to other supports. The novel composite materials were characterized by X-ray diffraction (XRD), Raman spectra, Scanning electron microscope (SEM), Transmission electron microscopy analysis and HR-TEM. https://www.selleckchem.com/products/a-1331852.html SEM and EDX techniques. High angle XRD confirmed the conversion of graphene oxide to reduced graphene oxide (RGO) with plant extract as a reducing agent. Both XRD and TEM techniques confirmed the Cu nanoparticle formation. The catalytic activity of all the prepared materials for the Ullmann coupling reactions of carbon-, oxygen-, and nitrogen-containing nucleophiles with iodobenzene was evaluated. From the results, 5 wt% Cu on amine-functionalized reduced graphene oxide/mesoporous silica nanocomposite (5 wt%Cu(0)-AAPTMS@RGO-MCM-41) exhibited excellent efficiency with 97% yield of the C-C coupling product in water at 80 °C in 5 h. The activity remained unaltered almost up to the fourth cycle. The Cu nanoparticles stabilized by organic amine group on RGO hybrid facilitated sustained activity.Ceria (CeO2) nanostructures are well-known in catalysis for energy and environmental preservation and remediation. Recently, they have also been gaining momentum for biological applications in virtue of their unique redox properties that make them antioxidant or pro-oxidant, depending on the experimental conditions and ceria nanomorphology. In particular, interest has grown in the use of biotemplates to exert control over ceria morphology and reactivity. However, only a handful of reports exist on the use of specific biomolecules to template ceria nucleation and growth into defined nanostructures. This review focusses on the latest advancements in the area of biomolecular templates for ceria nanostructures and existing opportunities for their (bio)applications.Water-soluble nanoclusters, which are facilely enrichable without changes in the original properties, are highly demanded in many disciplines. In this contribution, a new class of gold nanoclusters (AuNCs) was synthesized using glutathione disulfide (GSSG) as a reducing and capping agent under intermittent heating mode. The as-prepared GSSG-AuNCs had a higher quantum yield (4.1%) compared to the conventional glutathione-protected AuNCs (1.8%). Moreover, by simply introducing the GSSG-AuNC solution to acetonitrile at a volume ratio of 17, a new bottom phase was formed, in which GSSG-AuNCs could be 400-fold enriched without changes in properties, with a percentage recovery higher than 99%. The enrichment approach did not need additional instruments and was potentially suitable for large-scale enrichment of nanoclusters. Further, density functional theory calculations indicated that the hydrogen bonding between GSSG and acetonitrile plays a key role for the bottom phase formation. Our work suggests that the highly emissive GSSG-AuNCs possess great potential not only in fluorescent measurements but also in other scenarios in which high-concentration AuNCs may be needed, such as catalysis, drug delivery, and electronic and optical industries.In this short review (Perspective), we identify key features of the performance of biocatalysts developed by the immobilization of enzymes on the supports containing magnetic nanoparticles (NPs), analyzing the scientific literature for the last five years. A clear advantage of magnetic supports is their easy separation due to the magnetic attraction between magnetic NPs and an external magnetic field, facilitating the biocatalyst reuse. This allows for savings of materials and energy in the biocatalytic process. Commonly, magnetic NPs are isolated from enzymes either by polymers, silica, or some other protective layer. However, in those cases when iron oxide NPs are in close proximity to the enzyme, the biocatalyst may display a fascinating behavior, allowing for synergy of the performance due to the enzyme-like properties shown in iron oxides. Another important parameter which is discussed in this review is the magnetic support porosity, especially in hierarchical porous supports. In the case of comparatively large pores, which can freely accommodate enzyme molecules without jeopardizing their conformation, the enzyme surface ordering may create an optimal crowding on the support, enhancing the biocatalytic performance. Other factors such as surface-modifying agents or special enzyme reactor designs can be also influential in the performance of magnetic NP based immobilized enzymes.Polymeric hydrogels are currently at the center of research due to their particular characteristics. They have tunable physical, chemical, and biological properties making them a material of choice for a large range of applications. Polymer-composite and nanocomposite hydrogels were developed to enhance the native hydrogel's properties and to include numerous functionalities. In this work, alginate/gelatin-methacryloyl-based interpenetrating polymer network hydrogels were prepared with different alginate concentrations and investigated before and after the functionalization with nanoliposomes. The multiscale analysis was obtained through Fourier transform infrared spectroscopy and proton nuclear magnetic resonance. The results show interactions between two polymers as well as between the nanoliposomes and biopolymer.Endodontic treatment reduces the amount of bacteria by using antimicrobial agents to favor healing. However, disinfecting all of the canal system is difficult due to its anatomical complexity and may result in endodontic failure. Copper nanoparticles have antimicrobial activity against diverse microorganisms, especially to resistant strains, and offer a potential alternative for disinfection during endodontic therapy. This study evaluated the antibacterial action of copper nanoparticles (CuNPs) on an ex vivo multispecies biofilm using plaque count compared to the antibacterial activity of calcium hydroxide Ca(OH)2. There were significant differences between the Ca(OH)2 and CuNPs groups as an intracanal dressing compared with the CuNPs groups as an irrigation solution (p less then 0.0001). An increase in the count of the group exposed to 7 days of Ca(OH)2 was observed compared to the group exposed to Ca(OH)2 for 1 day. These findings differ from what was observed with CuNPs in the same period of time. Antibacterial activity of CuNPs was observed on a multispecies biofilm, detecting an immediate action and over-time effect, gradually reaching their highest efficacy on day 7 after application. The latter raises the possibility of the emergence of Ca(OH)2-resistant strains and supports the use of CuNPs as alternative intracanal medication.The review discusses the theoretical, experimental and toxicological aspects of the prospective biomedical application of functionalized magnetic nanoparticles (MNPs) activated by a low frequency non-heating alternating magnetic field (AMF). In this approach, known as nano-magnetomechanical activation (NMMA), the MNPs are used as mediators that localize and apply force to such target biomolecular structures as enzyme molecules, transport vesicles, cell organelles, etc., without significant heating. It is shown that NMMA can become a biophysical platform for a family of therapy methods including the addressed delivery and controlled release of therapeutic agents from transport nanomodules, as well as selective molecular nanoscale localized drugless nanomechanical impacts. It is characterized by low system biochemical and electromagnetic toxicity. A technique of 3D scanning of the NMMA region with the size of several mm to several cm over object internals has been described.In multicomponent thin films, properties and functionalities related to post-deposition annealing treatments, such as thermal stability, optical absorption and surface morphology are typically rationalized, neglecting the role of the substrate. Here, we show the role of the substrate in determining the temperature dependent behaviour of a paradigmatic two-component nanogranular thin film (Ag/TiO2) deposited by gas phase supersonic cluster beam deposition (SCBD) on silica and sapphire. Up to 600 °C, no TiO2 grain growth nor crystallization is observed, likely inhibited by the Zener pinning pressure exerted by the Ag nanoparticles on the TiO2 grain boundaries. Above 600 °C, grain coalescence, formation of However, the two substrates steer the evolution of the film morphology and optical properties in two different directions. anatase and rutile phases and drastic modification of the optical absorption are observed. On silica, Ag is still present as NPs distributed into the TiO2 matrix, while on sapphire, hundreds of nm wide Ag aggregates appear on the film surface.