Aagaardlauritzen9333

In this study, a large-scale in-cabin benzene series hazard detection is firstly performed on 20 electric buses by a full-scale climate chamber. The sources of BTEX are analyzed deeply by parts detection, and a series of effective measures are performed to reduce BTEX. Firstly, the in-cabin BTEX pollution with considerations of a series of parameters, such as interior configuration, environment temperature, vehicle age, and ventilation mode, is analyzed. The result shows that 1) The VOCs concentrations decrease with vehicle age, higher configuration level and better ventilation system (particularly, fresh wind mode reduce VOCs fastly), while increases with environment temperature; 2) BTEX in bus cabins occupy approximatively 70.1% of TVOC, thus the BTEX overproof is the main culprit which causes VOCs to exceed standard. Then, measurements on components/materials VOCs releases were performed in a small climate chamber to discriminate key species and their sources. Xylene released from glues materials is found as a key species that causes BTEX/VOC to exceed limitation. Lastly, some measures, such as optimizations of materials selection and manufacturing crafts, are adopted to improve in-cabin pollution, and positive effects are obtained. For example, ethylbenzene and xylene released from HL 125 (a polyurethane adhesive) decrease by 2456% and 1930% respectively after improvement. And in-cabin xylene and TVOC decrease by 2274% and 222%, respectively, and all of them are lower than limitation value.Material characterisation in nuclear environments is an essential part of decommissioning processes. This paper explores the feasibility of deploying commercial off the shelf (COTS) laser induced breakdown spectroscopy (LIBS) and Raman spectroscopy, for use in a decommissioning hot cell environment, to inform waste operation decision making. To operate these techniques, adapters and probes were designed and constructed, for each instrument, to form tools that a robotic arm could pick up and operate remotely from an isolated control room. The developed instrumentation successfully returned live measurement data to a control room for saving and further analysis (e.g. material classification/identification). Successful testing of the solutions was performed for contact LIBS, contact Raman and stand-off Raman on a PaR M3000 robotic arm, in a simulated hot cell environment and the limitations identified. Data obtained by the techniques are analysed, classified and presented in a 3D virtual environment. The spectral data collected by a basic COTS LIBS showed potential for use in contamination identification (beryllium is used as example). Potential for COTS, LIBS and Raman in decommissioning is established and improvements to the hardware, the measurement processes and how the data is stored and used, are identified.Arabidopsis arenosa is a pseudo-metallophyte, closely related to the model hyperaccumulator of Cd and Zn Arabidopsis halleri. A. arenosa occurs naturally in both diploid (2C) and tetraploid (4C) form, in contrast to A. halleri in which only diploid forms were found. Moreover, A. arenosa similarly to A. halleri often occupies heavy metal (HM) contaminated sites. Nevertheless, knowledge about the ecophysiology of this species is very limited. Therefore, we examined fourteen populations of A. arenosa of different ploidy from Central Europe in situ, focusing on photosynthetic efficiency, pigment content and ability to accumulate selected elements. The presented results indicate that several tetraploid populations exhibit the features of Cd and Zn hyperaccumulation. On the one hand, we noted differences in physiological parameters between the studied populations, on the other, harshness of the environment caused similar physiological response such as high HM pollution. All these features suggest that A. arenosa, especially as a new hyperaccumulator of Cd and Zn and autopolyploidyzation model, may be considered a very interesting research object, particularly when investigating the mechanisms of HMs accumulation and tolerance in plants.Intensive use of plastic films can induce contamination of microplastics (MPs) and phthalate esters (PAEs), but data on their relationship in agricultural soil has been scarce. This study investigated the occurrence of MPs and PAEs in Shouguang (SG) and Xuzhou (XZ), two typical facility agriculture areas in China with years of history of vegetable greenhouse plantation. Thirty-four soil samples covering greenhouse and non-greenhouse soils were collected. MPs were quantified using the laser direct infrared (LDIR) method to realize IR analysis for all the collected particles. The total MP and PAE was 380-3786 pieces/kg and 0.30-1.58 mg/kg, respectively. The MP content in greenhouse soil was significantly higher than that in non-greenhouse soil in both areas. However, this trend for PAEs was only found in XZ, but not in SG. A positive correlation was observed between MPs and PAEs in XZ but not in SG. Our results suggested that MP concentrations mainly depend on input, while the residue of PAEs in soil was a consequence of both input and removal. Even in the facility soil, MPs and PAEs may not always possess a definitive relationship, and other environmental factors must be considered to elucidate the relationship between them.The microbial fuel cell is a unique advantageous technology for the scientific community with the simultaneous generation of green energy along with bioelectroremediation of persistent hazardous materials. In this work, a novel approach of integrated system with bioelectricity generation from septic tank wastewater by native microflora in the anode chamber, while Psathyrella candolleana with higher ligninolytic enzyme activity was employed at cathode chamber for the biodegradation of polycyclic aromatic hydrocarbons (PAHs). Six MFC systems designated as MFC1, MFC2, MFC3, MFC4, MFC5, and MFC6 were experimented with different conditions. AZD-9574 research buy MFC1 system using natural microflora of STWW (100%) at anode chamber and K3[Fe(CN)6] as cathode buffer showed a power density and current density of 110 ± 10 mW/m2 and 90 ± 10 mA/m2 respectively. In the other five MFC systems 100% STWW was used at the anode and basidiomycetes fungi in the presence or absence of individual PAHs (naphthalene, acenaphthene, fluorene, and anthracene) at the cathode.