Abdihaley4742

D process. The new TTB concept is thus shown to provide a flowchart basis to predict the final microstructure based on FE temperature fields.Atrial fibrillation (AF) is the most common cardiac arrhythmia. It tends to cause multiple cardiac conditions, such as cerebral artery blockage, stroke, and heart failure. The morbidity and mortality of AF have been progressively increasing over the past few decades, which has raised widespread concern about unobtrusive AF detection in routine life. The up-to-date non-invasive AF detection methods include electrocardiogram (ECG) signals and cardiac dynamics signals, such as the ballistocardiogram (BCG) signal, the seismocardiogram (SCG) signal and the photoplethysmogram (PPG) signal. Cardiac dynamics signals can be collected by cushions, mattresses, fabrics, or even cameras, which is more suitable for long-term monitoring. Therefore, methods for AF detection by cardiac dynamics signals bring about extensive attention for recent research. This paper reviews the current unobtrusive AF detection methods based on the three cardiac dynamics signals, summarized as data acquisition and preprocessing, feature extraction and selection, classification and diagnosis. In addition, the drawbacks and limitations of the existing methods are analyzed, and the challenges in future work are discussed.The predatory gall midge, Feltiella acarisuga (Vallot) (Diptera Cecidomyiidae), is an acarivorous species that mainly feeds on spider mites (Acarina Tetranychidae). Because of its cosmopolitan distribution and predation efficacy, it is considered an important natural enemy available as a biological agent for augmentative biocontrol. However, despite its practical use, the thermal development and survival response to temperature have not yet been fully studied. In this study, we investigated the stage-specific development and survival of F. acarisuga at seven temperatures (11.5, 15.7, 19.8, 23.4, 27.7, 31.9, and 35.4 °C) to examine the effect of temperature on its lifecycle. All developmental stages could develop at 11.5-31.9 °C, but the performance was different according to the temperature. From the linear development rate models, the lower development threshold and thermal constant of the total immature stage were estimated at 8.2 °C and 200 DD, respectively. The potential optimal and upper threshold temperatures for the total immature stage were estimated as 29.3 and 35.1 °C using a non-linear development model. The operative thermal ranges for development and survival at 80% of the maximum rate were 24.5-32.3 and 14.7-28.7 °C, respectively. Thus, it was suggested that 24.5-28.7 °C was suitable for the total immature stage. In contrast, conditions around 8 °C and 35 °C should be avoided due to the lower development rate and high mortality. Our findings provide fundamental information for an effective mass-rearing and releasing program of F. acarisuga in an augmentative biocontrol program and help to predict phenology.When a longitudinal wave passes through a contact interface, second harmonic components are generated due to contact acoustic nonlinearity (CAN). The magnitude of the generated second harmonic is related to the contact state of the interface, of which a model has been developed using linear and nonlinear interfacial stiffness. However, this model has not been sufficiently verified experimentally for the case where the interface has a rough surface. The present study verifies this model through experiments using rough interfaces. To do this, four sets of specimens with different interface roughness values (Ra = 0.179 to 4.524 μm) were tested; one set consists of two Al6061-T6 blocks facing each other. The second harmonic component of the transmitted signal was analyzed while pressing on both sides of the specimen set to change the contact state of the interface. The experimental results showed good agreement with the theoretical prediction on the rough interface. The magnitude of the second harmonic was maximized at a specific contact pressure. As the roughness of the contact surface increased, the second harmonic was maximized at a higher contact pressure. The location of this maximal point was consistent between experiments and theory. In this study, an FEM simulation was conducted in parallel and showed good agreement with the theoretical results. Thus, the developed FEM model allows parametric studies on various states of contact interfaces.Austenitic 316L stainless steel is known for its good resistance to corrosion and oxidation. However, under conditions of appreciable mechanical wear, this steel had to demonstrate suitable wear protection. In this study, laser surface alloying with boron and some metallic elements was used in order to improve the hardness and wear behavior of this material. The microstructure was described in the previous paper in detail. The microhardness was measured using Vickers method. The "block-on-ring" technique was used in order to evaluate the wear resistance of laser-alloyed layers, whereas, the potentiodynamic method was applied to evaluate their corrosion behavior. The produced laser-alloyed layers consisted of hard ceramic phases (Fe2B, Cr2B, Ni2B or Ni3B borides) in a soft austenitic matrix. The significant increase in hardness and wear resistance was observed in the case of all the laser-alloyed layers in comparison to the untreated 316L steel. The predominant abrasive wear was accompanied by adhesive and oxidative wear evidenced by shallow grooves, adhesion craters and the presence of oxides. The corrosion resistance of laser-alloyed layers was not considerably diminished. The laser-alloyed layer with boron and nickel was the best in this regard, obtaining nearly the same corrosion behavior as the untreated 316L steel.This paper aims to develop recycled fiber reinforced cement plaster mortar with a good workability of fresh mixture, and insulation, mechanical and adhesive properties of the final hardened product for indoor application. The effect of the incorporation of different portions of three types of cellulose fibers from waste paper recycling into cement mortar (cement/sand ratio of 13) on its properties of workability, as well as other physical and mechanical parameters, was studied. The waste paper fiber (WPF) samples were characterized by their different cellulose contents, degree of polymerization, and residues from paper-making. learn more The cement to waste paper fiber mass ratios (C/WPF) ranged from 5001 to 31, and significantly influenced the consistency, bulk density, thermal conductivity, water absorption behavior, and compressive and flexural strength of the fiber-cement mortars. The workability tests of the fiber-cement mortars containing less than 2% WPF achieved optimal properties corresponding to plastic mortars (140-200 mm).