Tilleywall2844

To verify the validity of the sensing equation, we made another sensor in the same batch and got maximum errors of 0.36°C and 7.7×10-5RIU, respectively.For waters with stratified chlorophyll concentration (Chl), numerical simulations were carried out to gain insight into the forward models of subsurface reflectance and empirical algorithms for Chl from the ocean color. It is found that the Gordon and Clark (1980) forward model for reflectance using an equivalent homogeneous water with a weighted average Chl (⟨Chl⟩) as the input works well, but depending on the contribution of gelbstoff, the difference in reflectance between stratified and the equivalent homogeneous water can be more than 10%. selleck kinase inhibitor Further, the attenuation of upward light is better approximated as ∼1.5times that of the diffuse attenuation coefficient of downwelling irradiance. On the other hand, although the forward model for reflectance developed in Zaneveld et al. [Opt. Express13, 9052 (2005)] using equivalent homogeneous water with a weighted average of the backscattering to absorption ratio as the input also works well, this model cannot be used to obtain equivalent ⟨Chl⟩ for reflectance. Further, for empirical Chl algorithms designed for "Case 1" waters, it has been discovered that, for surface Chl in a range of ∼0.06-22.0mg/m3, the predictability of surface Chl is basically the same as that of ⟨Chl⟩ from the blue-green band ratio or the band difference of reflectance. Because ⟨Chl⟩ is wavelength and weighting-formula dependent, and it is required to have profiles of both Chl and the optical properties, these results emphasize that for empirical Chl algorithms, it is easier, less ambiguous, and certainly more straightforward and simple to use surface Chl for algorithm development and then its evaluation, rather than to use ⟨Chl⟩, regardless of whether or not the water is stratified.Traditional transmissive polarimetric methods can be used for wavelengths above 123 nm where birefringent materials transmit light and create significant birefringence. Below 123 nm, no suitable solution is known to measure the four Stokes parameters on a large wavelength range. Therefore, we study here an innovative reflective (rather than transmissive) polarimeter working in the far ultraviolet (FUV) range from 90 to 130 nm. We take advantage of the phase shift created by reflections as well as the different reflectivities for p (orthogonal ⊥) and s (parallel ∥ to the plane of incidence) polarizations to design an FUV polarimeter. Simulation of the analyzer and modulator using Mueller matrices coupled to polarimetric efficiencies calculations allowed optimization of reflective polarimeters for the first time, to the best of our knowledge. This opens up a new perspective for FUV polarimetry below 123 nm.Removal of a paint layer of 2024 aluminum alloy was studied using a nanosecond fiber pulsed laser with a maximum power of 30 W and the influence of laser cleaning energy density on the surface integrity of the substrate was explored. The cleaning energy density threshold of the paint layer is 17.69J/cm2 and the damage energy density threshold is 24.77J/cm2. The optimum cleanliness and surface integrity of laser cleaning were obtained when the energy density was 21.23J/cm2. Microhardness and Young's modulus of the surface after laser cleaning were improved by 6% and 25%, respectively. The mechanical properties of the surface of the substrate after laser cleaning were significantly improved, which is an advantage for this high-quality non-destructive cleaning technology of the aircraft skin surface paint layer.This work explores a theoretical solution for noise reduction in photonic systems using blackbody radiators. Traditionally, signal noise can be reduced by increasing the integration time during signal acquisition. However, increasing the integration time during signal acquisition will reduce the acquisition speed of the signal. By developing and applying a filter using a model based on the theoretical equations for blackbody radiation, the noise of the signal can be reduced without increasing integration time. In this work, three filters, extended Kalman filter, unscented Kalman filter (UKF), and extended sliding innovation filter (ESIF), are compared for blackbody photonic systems. The filters are tested on a simulated signal from five scenarios, each simulating different experimental conditions. In particular, the nonlinear filters, UKF and ESIF, showed a significant reduction of noise from the simulated signal in each scenario. The results show great promise for photonic systems using blackbody radiators that require post-process for noise reduction.Boresight and jitter are two fundamental pointing errors of laser illumination systems. A triangular-scanning algorithm is proposed to estimate the direction of the boresight via a three-step maximum boresight estimation and laser beam deflection procedure. On this basis, the closed-loop laser illumination (CLLI) for non-cooperative targets is realized, and the Cramer-Rao lower bounds (CRLB) performance in the lower limit of the pointing error is analyzed. Additionally, a Monte Carlo simulation system is built, and the performance of the CLLI algorithm is analyzed. The simulation results demonstrate that the triangular-scanning algorithm has good performance and can accurately estimate the direction of the boresight to achieve CLLI. Further study shows that the simulation results agree well with theoretical estimations and approximate the CRLB at the lower limit.Due to its hardness, strength, and transparency, sapphire is an attractive material for the construction of microfluidic devices intended for high-pressure applications, but its physiochemical properties resist traditional microfabrication and bonding techniques. Here a femtosecond pulsed laser was used to directly machine fluidic channels within sapphire substrates and to form bonds between machined and flat sapphire windows, resulting in the creation of sealed microfluidic devices. Sapphire-sapphire bond strength was determined by destructive mechanical testing, and the integrity of the bond was verified by the capillary filling of the channel with air and ethanol. This combination of optical micromachining and bonding establishes a fully integrated approach to the fabrication of sapphire-based microfluidic systems.