Sandersbatchelor5282

An optical true time delay line (OTTDL) is a fundamental building block for signal processing applications in microwave photonics and optical communications. Here, we experimentally demonstrate an index-variable OTTDL based on an array of 40 subwavelength grating (SWG) waveguides in silicon-on-insulator. learn more Each SWG waveguide in the array is 34 mm long and arranged in a serpentine manner; the average incremental delay between waveguides is about 4.7 ps, and the total delay between the first and last waveguides is approximately 181.9 ps. The waveguide array occupies a chip area of ∼6.5mm×8.7mm=56.55mm2. The proposed OTTDLs bring potential advantages in terms of compactness as well as operation versatility to a variety of microwave signal processing applications.Three-dimensional helical microstructures are abundant in nature and can be applied as chiral metamaterials for advanced nanophotonics. Here we report a flexible method to fabricate double-helical microstructures with single exposure by recording the chirality of incident optical vortices. Two coaxial optical vortices can interfere to generate a helical optical field, confirmed by the numerical simulation. The diameters of double-helical microstructures can be tailored by the magnitude of topological charges. This fast manufacturing strategy provides the opportunity to efficiently yield helical microstructures. Finally, the chirality of double-helical microstructures can be reversibly read by optical vortices, demonstrating a strong chiroptical response.Narrow-linewidth lasers are essential for various applications, but are limited by their size, weight, power, and cost requirements. Here we demonstrate a self-injection locked diode laser fabricated with a high quality factor fiber Fabry-Perot resonator, with a 145 Hz free-running linewidth. The locking scheme is all-fiber for plug-and-play operation. White frequency noise of 50Hz2/Hz is measured with over 42 dB reduction from the low-cost TO-can distributed feedback laser diode, and shows its wide applications in a compact and cost-effective way.We have demonstrated a 5 kW high-power monolithic fiber amplifier employing a homemade spindle-shaped ytterbium-doped fiber (YDF) based on the main oscillator power amplifier configuration. The YDF consists of a spindle-shaped core and cladding along the fiber length, with a core/cladding diameter of 27/410 µm at both ends and 39.5/600 µm in the middle. An output power of over 5 kW and beam quality of about 1.9 and an optical-to-optical conversion efficiency of 66.6% were achieved in the amplifier under a bidirectional pump scheme. While operating at the maximum power, the laser performance was evaluated, and the transverse mode instability and stimulated Raman scattering effects were well mitigated. To the best of our knowledge, this is the highest power demonstration in a continuous-wave fiber laser employing a tapered fiber. Further power scaling is promising by optimizing the structure of the YDF.Manipulation of spoof surface plasmons (SSPs) has recently intrigued enormous interest due to the capability of guiding waves with subwavelength footsteps. However, most of the previous studies, manifested for a single functionality, are not suitable for multifunctional integrated devices. Herein, a bifunctional Luneburg-fish-eye lens is proposed based on a 2D metal pillar array. First, by tuning the dimension of the metal pillars in the array, its ability to precisely manipulate the SSPs along one direction is confirmed, achieving subwavelength focusing and imaging with a resolution up to 0.14λ. Then, separately controlling the propagation of the SSPs along the orthotropic directions is further implemented, and the bifunctional Luneburg-fish-eye lens is realized. It is experimentally characterized as a Luneburg lens along the x axis, whereas in the y axis, it presents the properties of a Maxwell fish-eye lens. This bifunctional lens can reduce the system complexity and exert flexibility in multifunctional applications, while the proposed metal pillar-based design method broadens the application range of the gradient refractive-index lens in microwave, terahertz, and even optical ranges.We proposed a passively stabilized Q-switched ErLu2O3 laser at 2845 nm, applying a MXene Nb2CTx nanosheets saturable absorber prepared by the liquid-phase exfoliation method. The surface morphology and nonlinear properties of this nanosheet were systematically characterized. Average output power of 542 mW for the Q-switched laser was obtained under 7.26 W of absorbed pump power. Meanwhile, the Q-switched pulse duration was measured to be 223.7 ns with 142.9 kHz repetition rate corresponding to a peak power of 16.96 W.We report on the realization of delivering coherent optical frequency to multiple places based on passive phase noise cancellation over a bus topology fiber network. This technique mitigates any active servo controller on the main fiber link and at arbitrary access places as opposed to the conventional technique, in which an active phase compensation circuit has to be adopted to stabilize the main fiber link. Although the residual fiber phase noise power spectral density in the proposed technique turns out to be a factor of seven higher than that of in the conventional multiple-access technique when the access place is close to the end of the fiber link, it could largely suppress the phase noise introduced by the servo bumps, improve the response speed and phase recovery time, and minimize hardware overhead in systems with many stations and connections without the need for active servo circuits including phase discriminators and active compensators. The proposed technique could considerably simplify future efforts to make precise optical frequency signals available to many users, as required by some large-scale science experiments.In this paper, we propose spatiotemporal modulation projection lithography (STPL) technology, which is a spatiotemporal modulation technology applied to the conventional digital micromirror device (DMD) projection lithography system. Through coordinating the micro-movement of the piezoelectric stage, the flexible pattern generation of DMD, and the exposure time, the proposed STPL enables us to fabricate a microstructure with smooth edges, accurate linewidth, and accurate line position. Further application on fabricating a diffraction lens has been implemented. The edge sawtooth of the Fresnel zone plate fabricated by using the STPL is reduced to 0.3 µm, the error between the actual measured linewidth and the ideal linewidth is only within ±0.1µm, and the focal length is 15 mm, which is basically consistent with the designed focal length. These results indicated that STPL can serve a significant role in the micromanufacturing field for achieving high-fidelity microdevices.