Severinsenterkildsen8191

Amidinate and guanidinate ligands have been used extensively to produce volatile and thermally stable precursors for atomic layer deposition. The triazenide ligand is relatively unexplored as an alternative ligand system. Herein, we present six new Al(III) complexes bearing three sets of a 1,3-dialkyltriazenide ligand. These complexes volatilize quantitatively in a single step with onset volatilization temperatures of ∼150 °C and 1 Torr vapor pressures of ∼134 °C. Differential scanning calorimetry revealed that these Al(III) complexes exhibited exothermic events that overlapped with the temperatures of their mass loss events in thermogravimetric analysis. Using quantum chemical density functional theory computations, we found a decomposition pathway that transforms the relatively large hexacoordinated Al(III) precursor into a smaller dicoordinated complex. The pathway relies on previously unexplored interligand proton migrations. These new Al(III) triazenides provide a series of alternative precursors with unique thermal properties that could be highly advantageous for vapor deposition processes of Al containing materials.Piezoelectricity in two-dimensional (2D) transition-metal dichalcogenides (TMDs) has attracted significant attention due to their unique crystal structure and the lack of inversion centers when the bulk TMDs thin down to monolayers. Although the piezoelectric effect in atomic-thickness TMDs has been reported earlier, they are exfoliated 2D TMDs and are therefore not scalable. Here, we demonstrate a superior piezoelectric effect from large-scale sputtered, asymmetric 2D MoS2 using meticulous defect engineering based on the thermal-solvent annealing of the MoS2 layer. Selleckchem MS023 This yields an output peak current and voltage of 20 pA and 700 mV (after annealing at 450 °C), respectively, which is the highest piezoelectric strength ever reported in 2D MoS2. Indeed, the piezoelectric strength increases with the defect density (sulfur vacancies), which, in turn, increases with the annealing temperature at least up to 450 °C. Moreover, our piezoelectric MoS2 device array shows an exceptional piezoelectric sensitivity of 262 mV/kPa with a high level of uniformity and excellent performance under ambient conditions. A detailed study of the sulfur vacancy-dependent property and its resultant asymmetric structure-induced piezoelectricity is reported. The proposed approach is scalable and can produce advanced materials for flexible piezoelectric devices to be used in emerging bioinspired robotics and biomedical applications.Defect influences on the photoactivity of ZnO nanoparticles prepared by a powdered coconut water (ACP) assisted synthesis have been studied. The crystalline phase and morphology of ZnO nanoparticles were effectively controlled by adjusting the calcination temperature (400-700 °C). An induced transition of hybrid Zn5(CO3)2(OH)6/ZnO nanoparticles to single-phase ZnO nanoparticles was obtained at 480 °C. The morphological analysis revealed a formation of ZnO nanoparticles with semispherical (∼6.5 nm)- and rod-like (∼96 nm) shapes when the calcination temperatures were 400 and 700 °C, respectively. Photoluminescence characterizations revealed several defects types in the samples with VZn and VO + being in the self-assembly of semispherical- and rod-like ZnO nanoparticles. The photocatalytic activity of the ZnO nanoparticles was examined by assessing the degradation of methylene blue in an aqueous solution under low-intensity visible-light irradiation (∼3 W m-2). The results point toward the self-assembly of semispherical- and rod-like ZnO nanoparticles that had significantly better photocatalytic activity (∼31%) in comparison to that of spherical-agglomerated- or near-spherical-like species within 120 min of irradiation. The possible photocatalytic mechanism is discussed in detail, and the morphology-driven intrinsic [VZn+VO + ] defects are proposed to be among the active sites of the ZnO nanoparticles enhancing the photocatalytic activity.The high theoretical energy densities of lithium-air batteries (LAB) make this technology an attractive energy storage system for future mobility applications. Li2O2 growth process on the cathode relies on the surrounding chemical environment of electrolytes. Low conductivity and strong reactivity of Li2O2 discharge products can cause overpotential and induce side reactions in LABs, respectively, eventually leading to poor cyclability. The capacity and reversibility of LABs are highly susceptible to the morphology of the Li2O2 discharge products. Here, we identify for the first time that a seed layer formed by the combination of a cathode and an electrolyte determines the morphology of Li2O2 discharge products. This seed layer led to its high reversibility with a large areal capacity (up to 10 mAh/cm2). Excellent OER (oxygen evolution reaction) was achieved by the formation of a favorable interface between the carbon electrode and electrolyte, minimizing the decomposition of the electrolyte. These remarkable improvements in LAB performance demonstrate critical progress toward advancing LAB into practical uses, which would exploit good reversibility of LABs in pouch-type cell arrangements with 1.34 Ah.In this study, we assessed the feasibility of using ordinary face masks as a sampling means to collect airborne polycyclic aromatic hydrocarbons (PAHs). Nonwoven fabric masks can trap three-ring or larger PAHs at a high efficiency (>70%) and naphthalene at ∼17%. The sampling method is quantitative as confirmed by comparison with the standard method of the National Institute for Occupational Safety and Health. In conjunction with sensitive fluorescence detection, the method was applied to quantify nine airborne PAHs in a range of indoor and outdoor environments. Wearing the mask for 2 h allowed quantification of individual PAHs as low as 0.07 ng/m3. The demonstration shows applicability of the method in monitoring PAHs down to ∼30-80 ng/m3 in university office and laboratory settings and up to ∼900 ng/m3 in an incense-burning temple. Compared with traditional filter-/sorbent tube-based approaches, which require a sampling pump, our new method is simple, convenient, and inexpensive. More importantly, it closely tracks human exposure down to the individual level, thus having great potential to facilitate routine occupational exposure monitoring and large-scale surveillance of PAH concentrations in indoor and outdoor environments.