Estesmullen9821

In conclusion, the nanohybrid Alg-GO hydrogel could be used as an injectable hydrogel for soft tissue engineering applications.The present work focuses on the development of cellulose nanofibrils (CNF) film that derived from sustainable biomass resources, which potentially to work as bio-based conductive membranes that assembled into supercapacitors. The chemically purified cellulose was isolated from different parts of coconut (coconut shell and its husk) and further subjected to 2,2,6,6-tetramethylpiperidine-1-oxyl radical (TEMPO)-mediated oxidation for CNF preparation. Physicochemical properties of prepared CNFs were studied in terms of chemical characteristics & crystallinity, surface functionalities, surface morphology, and thermal properties. Both coconut shell-derived CNF and coconut husk-derived CNF fulfilled with nanocellulose's characteristics with fibres width ranged of 70-120 nm and 150-330 nm, respectively. CNF films were further prepared by solvent casting method to measure the modulus elasticity, piezoelectric and dielectric properties of the films. Mechanical study indicated that coconut shell-derived CNF film showed a higher value of elastic modulus than the coconut husk-derived CNF film, which was 8.39 GPa and 5.36 GPa, respectively. The effectiveness of electrical aspects for CNF films are well correlated with the crystallinity and thermal properties, associated with it's composition of different coconut's part.The present work aims to examine the structural properties of polyurethanes bio-composites with mole ratios of alginate and chitosan. For this concern, a two-step reaction mechanism was carried out; in the first step isocyanate (-NCO) terminated pre-polymer was synthesized by the reaction of hexamethylene diisocyanate (HMDI) and hydroxyl-terminated polybutadiene (HTPB). The pre-polymer was further extended with 1,4-butanediol (BDO), chitosan (CS) and alginate (ALG) in the second step. Structural and functional group elucidation was done by using Fourier Transform Infra-red (FT-IR) and proton nuclear magnetic resonance (1H NMR) spectroscopy. The crystallinity of the prepared samples was investigated by using X-ray diffraction (XRD) method, the maximum observed intensity was 7704 a.u. The thermal properties of polyurethane composites were carried out using thermogravimetric analysis (TGA) and differential scanning calorimeter (DSC). The TGA results showed that thermal stability of RPU-5 was 20 °C more than RPU-1 at each corresponding degradation temperature. It is observed all physical parameters like crystallinity, glass transition temperature, melting point are much dependent on ratio of chain extenders. Overall, CS based samples along with small amount of ALG showed better thermal properties.Effects of Elm tree sawdust pretreatments using alkali and alkaline earth metals (NaCl, KCl, CaCl2, MgCl2 and Elm tree ash) and deashing solutions (water, HCl, HNO3 and aqua regia) before the carbonization process on the porosity of produced activated carbons and Pb (II) and Cr (VI) adsorption were studied. The activated carbons were characterized by pore size distribution, surface area, FTIR, and SEM-EDX analysies. Based on the results, HCl leaching pretreatment of the biomass increased the activated carbon adsorption capacity of Cr (VI) from 114 to 190 mg g-1. The treatment of biomass with alkali and alkali earth metal salts, especially MgCl2, remarkably increased the activated carbon adsorption capacity of Pb (II) from 233 to 1430 mg g-1. The results indicated that Pb (II) adsorption was attributed to both the mesoporous structure of activated carbon and the abundance of Mg on the activated carbon's surface. On the other hand, the micropores played a major role in Cr (VI) adsorption capacity. The development of the micro- or mesoporous structure of activated carbons through pretreatment of lignocellulosic precursor could be an approach for providing high performance activated carbons for Pb (II) and Cr (VI) removal from aqueous solutions.The present study aimed to produce thermoplastic starch films with different concentrations of thermoplastic pectin and the addition of 4% lignin microparticles as a reinforcing and active agent. The pectin improved the modulus of elasticity, and decreased the elongation at break. In addition, it improved the UV light protection to 100% at 320 nm and 95.9% at 400 nm. The incorporation of lignin microparticles improved the thermal stability of the blends made with 25% and 50% thermoplastic pectin when compared to the pectin-free blends. The blend with 25% thermoplastic pectin led to an increase of 75.8% and 34% in elongation at break and deformation of the films, respectively. This blend also improved the UV light protection to 100% due to its dark brown color. Regarding the permeability properties, the films with 25% and 50% thermoplastic pectin showed lower oxygen permeability (48% and 65%) and an increase in the antioxidant activities from 2.7% to 71.08% and 4.1% to 79.28%, respectively. Thus, the polymer blend with 25% thermoplastic pectin with the incorporation of lignin microparticles proved to be a good alternative for use in foods sensitive to the effects of oxygen and UV light.Fatty acid desaturase catalyzes the desaturation reactions by insertion of double bonds into the fatty acyl chain, producing unsaturated fatty acids. Though soluble fatty acid desaturases have been studied widely in advanced organisms, there are very limited studies of membrane fatty acid desaturases due to the difficulty of generating recombinant desaturase. Selleckchem Ginkgolic Brassica napus is a rapeseed, which possesses a range of different membrane-bound desaturases capable of producing fatty acids including Δ3, Δ4, Δ8, Δ9, Δ12, and Δ15 fatty acids. The 1155 bp open reading frame of Δ12 fatty acid desaturase (FAD12) from Brassica napus codes for 383 amino acid residues with a molecular weight of 44 kDa. It was expressed in Escherichia coli at 37 °C in soluble and insoluble forms when induced with 0.5 mM IPTG. Soluble FAD12 has been purified using Ni2+-Sepharose affinity chromatography with a total protein yield of 0.728 mg/mL. Gas chromatography-mass spectrometry (GC-MS) analysis revealed that desaturase activity of FAD12 could produce linoleic acid from oleic acid at a retention time of 17.