Fiskerkemp0760

We introduce a setup to measure high-resolution inelastic x-ray scattering at the High Energy Density scientific instrument at the European X-Ray Free-Electron Laser (XFEL). The setup uses the Si (533) reflection in a channel-cut monochromator and three spherical diced analyzer crystals in near-backscattering geometry to reach a high spectral resolution. An energy resolution of 44 meV is demonstrated for the experimental setup, close to the theoretically achievable minimum resolution. The analyzer crystals and detector are mounted on a curved-rail system, allowing quick and reliable changes in scattering angle without breaking vacuum. The entire setup is designed for operation at 10 Hz, the same repetition rate as the high-power lasers available at the instrument and the fundamental repetition rate of the European XFEL. Among other measurements, it is envisioned that this setup will allow studies of the dynamics of highly transient laser generated states of matter.A solid-state suppress grid power supply (SGPS) is developed to be applied to the 5 MW level neutral beam injection (NBI) on HL-2M Tokamak. The power supply consists of ten modules in series, with an index of 560 V/40 A. Each of the modules is composed of an isolated transformer, rectifier, filter tank, insulated gate bipolar transistor switch, gate-drive circuit, free-wheeling diode, and so forth. An embedded system STM32F103 is used for controlling and protecting the SGPS. Meanwhile, the transient output capacity of the SGPS is tested. The effect of the output voltage of the SGPS on the extracted beam current is studied. The experimental results show that there is a turning point in the relationship between the suppress voltage and the extracted beam current. When the rate of the absolute value of the suppress voltage and the gradient voltage is more than 2.5%, the efficiency of the extracted beam of the ion source can be improved. Compared with the previous types of equipment of the NBI system, the extracted beam success rate of the new SGPS increased by more than 20%. The SGPS meets the requirements of the NBI system.In the past, the Stern-Gerlach experiment has been used as a standard method for analyzing the population of magnetic substates contained in spin-polarized and/or state-selected atomic/molecular beams. However, this experiment is quite demanding due to its low signal intensity and difficulty in beam alignment. The present study shows that the use of a hexapole magnet and a spin flipper, together with the time-of-flight analysis, allows us to conduct an almost equivalent analysis while greatly improving the signal intensity. Applications to the analysis of spin-polarized triplet excited helium and state-selected O2(  3 Σg-) beams are presented.The second-order photon correlation function g2(τ) is of great importance in quantum optics. g2(τ) is typically measured with the Hanbury Brown and Twiss (HBT) interferometer, which employs a pair of single-photon detectors and a dual-channel time acquisition module. Here, we demonstrate a new method to measure and extract g2(τ) with a standard single-photon avalanche photodiode (dead-time = 22 ns) and a single-channel time acquisition module. This is realized by shifting the coincidence counts of interest to a time window not affected by the dead-time and after-pulse of the detection system using a fiber-based delay line. The new scheme is verified by measuring g2(τ) from a single colloidal nanocrystal. Photon antibunching is unambiguously observed and agrees well with the result measured using the standard HBT setup. Our scheme simplifies the higher-order correlation technique and might be favored in cost-sensitive circumstances.Resistive heating of a sample in a diamond anvil cell (DAC) can generate a homogeneous temperature field across the sample chamber with reliable temperatures measured by a thermocouple. It is of importance in experiments aiming at exploring phase diagrams and quantifying thermoelastic properties of materials. Here, we present a ring-heater design developed for BX90 diamond anvil cells (DACs). It is made of a ring-shaped aluminum oxide holder hosting a tungsten wire coil inside and coupled with Ar + 2% H2 gas to prevent oxidation during experiment. This modular plug-and-play design enables in situ studies of samples via x-ray diffraction up to a temperature of 1700 K. Temperature in the BX90 sample volume as measured through a thermocouple was calibrated using the melting point of gold. As an application of this design, we report the thermal expansion coefficient of MgO at 9.5(1) GPa.A simple systematic calibration method based on acceleration and angular rate measurements is introduced for the fiber-optic gyro strapdown inertial navigation system in this paper. Meanwhile, a unified mathematical framework and an iterative calculation method are designed for the systematic calibration method. Using this method, one can estimate the fiber-optic gyro inertial measurement unit (FOG IMU) parameters both at a manufacturer's facility and in the field. In order to get all FOG IMU parameters, a procedure adopted based on this approach consists of two stages First, FOG IMU raw data (accelerometer and gyro readouts) are accumulated in 19 specified FOG IMU positions. Second, the accumulated data are processed by special software to estimate all FOG IMU parameters. In addition, observability analysis of the method in 19 specified FOG IMU positions is done without the limitation of FOG IMU's initial orientation, and this analysis provides theoretical support for the application in a complex terrain. Moreover, the influence of gravity disturbance is analyzed for the first time. The analysis and experiment results show that the systematic calibration method provided by this work can meet the requirement of FOG IMU calibration.A miniature scanning electrostatic energy analyzer has been developed for measurements of the ion energy distribution in low-pressure plasma discharges. The retarding potential analyzer utilizes four grids to reject the incident electron flux and discriminate the ion energy. It features a compact size of 5-mm diameter and 2.5-mm thickness and uses a simple configuration to mount the grids and provide voltage isolation using high temperature ceramic cement that avoids complicated grid alignment or MEMS fabrication techniques. Mounting on a fast-scanning two-axis probe drive eliminates overheating of the ceramics and subsequent current leakage, which permits insertion into challenging locations and provides profiles of the ion energy in the plasma discharge. Guidelines for the analyzer design for high density operation are discussed, and the performance of the analyzer is shown for measurements in a hollow cathode plume in xenon plasmas.We report the design and testing of a custom-built experimental setup for dip-coating from volatile solutions under microgravity conditions onboard an aircraft. Function and safety considerations for the equipment are described. The equipment proved to work well, both concerning the safety and the preparation of thin films. No leakage of the solvents, nor the solvent vapors, was detected, not even in a situation with a fluctuating gravitational field due to bad weather conditions. We have shown that the equipment can be used to prepare thin films of polymer blends, relevant for organic solar cells, from solution in a feasible procedure under microgravity conditions. The prepared films are similar to the corresponding films prepared under 1 g conditions, but with differences that can be related to the absence of a gravitational field during drying of the applied liquid coating. We report on some introductory results from the characterization of the thin films that show differences in film morphology and structure sizes.Microelectromechanical system resonant sensors are widely used in high precision applications. Frequency measurement plays an important role in such frequency readout sensors. This paper proposed an improved modified frequency measurement method based on the multi-phase clock (MPC), which can effectively improve the measurement accuracy but does not reduce the output rate. Innovative claims include (1) building a model of measurement error for MPC in which the probability of triggering error under different conditions is calculated, (2) improving the accuracy of the MPC measurement by phase reverse, and (3) proposing an algorithm to eliminate jitters of the measured signal. We compared the measurement results of this optimized MPC realized by the field programmable gate array (FPGA) device with those of the conventional MPC, spectral measurement, and equal precision measurement implemented with the National Instruments acquisition equipment PXI-4461 and USB-6366, respectively. The results show that the bias instability of the adopted method is ∼10 µHz obtained by Allan variance analysis, which is better than that of the other three methods. see more It can meet the accuracy requirements for the resonant frequency measurement of state-of-the-art resonant accelerometers. In addition, an algorithm running in FPGA is proposed to eliminate jitters caused by the noise of the measured signal for enhancing the robust of optimized MPC. The results demonstrate that the optimized MPC has features of high accuracy and anti-interference capability and can be easily transferred to the application specific integrated circuit in the future due to its full digital circuit version.A set of three apparatus enabling RF exposure of aerosolized pathogens at four chosen frequencies (2.8 GHz, 4.0 GHz, 5.6 GHz, and 7.5 GHz) has been designed, simulated, fabricated, and tested. Each apparatus was intended to operate at high power without leakage of RF into the local environment and to be compact enough to fit within biocontainment enclosures required for elevated biosafety levels. Predictions for the range of RF electric field exposure, represented by the complex electric field vector magnitude, that an aerosol stream would be expected to encounter while passing through the apparatus are calculated for each of the chosen operating frequencies.The beamline for advanced dichroism of the Istituto Officina dei Materiali-Consiglio Nazionale delle Ricerche, operating at the Elettra synchrotron in Trieste (Italy), works in the extreme ultraviolet-soft x-ray photon energy range with selectable light polarization, high energy resolution, brilliance, and time resolution. The beamline offers a multi-technique approach for the investigation of the electronic, chemical, structural, magnetic, and dynamical properties of materials. Recently, one of the three end stations has been dedicated to experiments based on electron transfer processes at the solid/liquid interfaces and during photocatalytic or electrochemical reactions. Suitable cells to perform soft x-ray spectroscopy in the presence of liquids and reagent gases at ambient pressure were developed. Here, we present two types of static cells working in transmission or in fluorescence yield and an electrochemical flow cell that allows us to carry out cyclic voltammetry in situ and electrodeposition on a working electrode and to study chemical reactions under operando conditions. Examples of x-ray absorption spectroscopy measurements performed under ambient conditions and during electrochemical experiments in liquids are presented.