Clancyriber2012

[This corrects the article DOI 10.34172/joddd.2020.023.].Background. This study was conducted to investigate root canal overfilling with different material placement techniques in primary teeth. Methods. A systematic search was undertaken by searching PubMed/MEDLINE and Scopus for English language peer-reviewed articles published until February 2018 that reported primary tooth pulpectomy overfilling. Two reviewers independently screened and identified studies in terms of the selection criteria and independently collected the data using a specially designed data extraction form. The overfilling rate was the primary summary measure. The weighted pooled overfilling rates were estimated by random-effects meta-analysis. Results. Twenty clinical and four in vitro studies met the eligibility criteria. In the clinical studies, the pooled overfilling rate for zinc oxide-eugenol (ZOE) was 23.3% with a lentulo spiral mounted on a handpiece, 22.7% with a hand-held lentulo spiral, and 17% with a plugger. The pooled overfilling rate for calcium hydroxide-based materials was 16.7% with a lentulo spiral mounted on a handpiece, 14.7% with a hand-held lentulo spiral, 19.6% with a syringe, and 25.7% with a plugger. In the in vitro studies, neither individual overfilling rates nor two-by-two comparisons were subjected to meta-analysis because of an inadequate number of studies. Conclusion. The lowest overfilling rate in the clinical studies was related to plugger and handheld lentulo spiral techniques for ZOE and calcium hydroxide-based materials, respectively.Background. This study compared the force decay pattern of two different orthodontic active tiebacks (ATBs) exposed to five different commercially available mouth rinses. Methods. Nigericin sodium chemical structure In this in vitro study, 90 transparent ATBs and 90 gray ATBs were divided into six groups; one was the control group, and the others were exposed to one of these mouth rinses twice a day for 60 seconds Listerine, chlorhexidine, Orthokin, Persica, and fluoride. The initial force of each ATB was 250 g at a 24-mm extension. The force of ATBs was measured on days 1, 7, 14, and 28 using a digital gauge. Results. The highest percentage of force loss was observed between days 14 and 28 (P less then 0.05). At the end of the study, the Persica group exhibited the highest force degradation in both ATB types. In the transparent ATBs, it was followed by Orthokin, Listerine, fluoride, chlorhexidine, and control groups, respectively. In the gray ATBs, Orthokin, chlorhexidine, control, Listerine, and fluoride groups exhibited the highest force decay in descending order. In some groups, the differences between transparent and gray ATBs were significant. In the control group, the force of transparent ATB was significantly higher than gray ones on days 7 and 14 but not significantly after four weeks. Conclusion. ATBs' force degradation could be exacerbated by the use of some mouth rinses. There were some differences between force relaxation patterns of transparent and gray ATBs. The data could be beneficial in choosing appropriate O-rings for making ATBs.Background. The present study aimed to evaluate the bond strength of metal bracket (MB) and ceramic bracket (CB) bonded to different CAD/CAM ceramic substrates etched with hydrofluoric acid (HFA) vs. phosphoric acid (PA). Methods. A total of 120 CAD/CAM ceramic blocks in 12 groups were fabricated from three different CAD/CAM ceramic materials VITABLOCS Mark II, VITAENAMIC, and IPS e.max CAD. Each ceramic material group was divided into two etching groups one treated with 9.5% HFA and the other treated with 37%. Sixty metal and CBs of the upper right central incisor were bonded to the HFA-treated blocks. Another 60 metal and CBs were bonded to the PA treated blocks. All the bonded specimens were thermocycled before shear bond strength (SBS) testing. Then the bond failure mode was recorded Results. There were no significant differences in SBS values between the three CAD/CAM ceramic materials. The HFA-treated specimens exhibited significantly higher SBS values than the PA-treated specimens. Also, the SBS values of CBs were significantly higher than the metal brackets (MBs). The adhesive remnant index (ARI) score was 4 for most of the groups, indicating that almost no adhesive remained on the porcelain surface. Conclusion. The CAD/CAM ceramic type did not influence SBS; however, HFA exhibited significantly higher SBS compared to PA.Background. This study aimed to investigate the endodontic debridement efficacy of different sodium hypochlorite (NaOCl) irrigation regimens with and without ultrasonic agitation, followed by ethylenediaminetetraacetic acid (EDTA) via scanning electron microscopy (SEM) after using a rotary instrumentation system. Methods. Mandibular premolars (n=50) were randomly divided into five experimental groups (n=10) for root canal instrumentation with ProTaper Universal rotary system up to F3. The root canal system was treated with intracanal-heated NaOCl (100°C) or preheated NaOCl (55°C), followed by ultrasonic agitation and EDTA treatment. Samples irrigated with conventional needle irrigation (CNI) using normal saline solution were used as controls. Debridement efficacy was analyzed by SEM. A five-point scale was used to estimate the presence/absence of debris for each canal segment (coronal, middle, and apical). The results were analyzed using one-way ANOVA and post hoc Tukey tests (P less then 0.05). Results. The experimental groups exhibited less debris compared to CNI with saline (P less then 0.05). The amount of debris decreased significantly for the group with NaOCl intracanal heating compared to extraoral heating. Ultrasonic agitation further enhanced the root canal debridement efficacy of NaOCl. Conclusion. In summary, intracanal heating of NaOCl with and without ultrasonic agitation followed by EDTA appears to be a promising method to flush debris from the root canal system.Background. Local or systemic issues might prevent installing a sufficient number of dental implants for fixed prosthetic rehabilitation. Splinting dental implants and natural teeth in fixed dentures could overcome such limitations. Therefore, this study aimed to evaluate the influence of the number of dental abutments in the biomechanics of tooth‒implant-supported fixed partial dentures (FPDs). The null hypothesis was that increasing the number of abutment teeth would not decrease the stress over the abutments and surrounding bone. Methods. Left mandibular lateral incisor, canine, premolars, and molars were reconstructed through computed tomography and edited using image processing software to represent a cemented fixed metal‒ceramic partial denture. Three models were set to reduce the number of abutment teeth 1) lateral incisor, canine, and first premolar; 2) canine and first premolar; 3) the first premolar. The second premolar and first molar were set as pontics, and the second molar was set as an implant abutment in all the models.