Bossenconner1317

An electron backscattered diffraction (EBSD) method provides information about the crystallographic structure of materials. this website However, a surface subjected to analysis needs to be well-prepared. This usually requires following a time-consuming procedure of mechanical polishing. The alternative methods of surface preparation for EBSD are performed via electropolishing or focus ion beam (FIB). In the present study, plasma etching using a glow discharge optical emission spectrometer (GD-OES) was applied for surface preparation for EBSD analysis. The obtained results revealed that plasma etching through GD-OES can be successfully used for surface preparation for EBSD analysis. However, it was also found that the plasma etching is sensitive for the alloy microstructure, i.e., the presence of intermetallic phases and precipitates such as carbides possess a different sputtering rate, resulting in non-uniform plasma etching. Preparation of the cross-section of oxidized CM247 revealed a similar problem with non-uniformity of plasma etching. The carbides and oxide scale possess a lower sputtering rate than the metallic matrix, which caused formation of relief. Based on obtained results, possible resolutions to suppress the effect of different sputtering rates are proposed.Autograft (AG) is the gold standard for bone grafts, but limited quantities and patient morbidity are associated with its use. AG extenders have been proposed to minimize the volume of AG while maintaining the osteoinductive properties of the implant. In this study, poly(ester urethane) (PEUR) and poly(thioketal urethane) (PTKUR) AG extenders were implanted in a 20-mm rabbit radius defect model to evaluate new bone formation and graft remodeling. Outcomes including µCT and histomorphometry were measured at 12 weeks and compared to an AG (no polymer) control. AG control examples exhibited new bone formation, but inconsistent healing was observed. The implanted AG control was resorbed by 12 weeks, while AG extenders maintained implanted AG throughout the study. Bone growth from the defect interfaces was observed in both AG extenders, but residual polymer inhibited cellular infiltration and subsequent bone formation within the center of the implant. PEUR-AG extenders degraded more rapidly than PTKUR-AG extenders. These observations demonstrated that AG extenders supported new bone formation and that polymer composition did not have an effect on overall bone formation. Furthermore, the results indicated that early cellular infiltration is necessary for harnessing the osteoinductive capabilities of AG.Fatigue analysis is of great significance for thin-walled structures in the spacecraft industry to ensure their service reliability during operation. Due to the complex loadings of thin-walled structures under thermal-structural-acoustic coupling conditions, the calculation cost of finite element (FE) simulations is relatively expensive. To improve the computational efficiency of dynamic reliability analysis on thin-walled structures to within acceptable accuracy, a novel probabilistic approach named DC-ILSSVR was developed, in which the rotation matrix optimization (RMO) method was used to initially search for the model parameters of least squares support vector regression (LS-SVR). The distributed collaborative (DC) strategy was then introduced to enhance the efficiency of a component suffering from multiple failure modes. Moreover, a numerical example with respect to thin-walled structures was used to validate the proposed method. The results showed that RMO performed on LS-SVR model parameters provided competitive prediction accuracy, and hence the reliability analysis efficiency of thin-walled pipe was significantly improved.Over the last two decades, calcium silicate-based materials have grown in popularity. As root canal sealers, these formulations have been extensively investigated and compared with conventional sealers, such as zinc oxide-eugenol and epoxy resin-based sealers, in in vitro studies that showed their promising properties, especially their biocompatibility, antimicrobial properties, and certain bioactivity. However, the consequence of their higher solubility is a matter of debate and still needs to be clarified, because it may affect their long-term sealing ability. Unlike conventional sealers, those sealers are hydraulic, and their setting is conditioned by the presence of humidity. Current evidence reveals that the properties of calcium silicate-based sealers vary depending on their formulation. To date, only a few short-term investigations addressed the clinical outcome of calcium silicate-based root canal sealers. Their use has been showed to be mainly based on practitioners' clinical habits rather than manufacturers' recommendations or available evidence. However, their particular behavior implies modifications of the clinical protocol used for conventional sealers. This narrative review aimed to discuss the properties of calcium silicate-based sealers and their clinical implications, and to propose rational indications for these sealers based on the current knowledge.Although the general instability of the iron nitride γ'-Fe4N with respect to other phases at high pressure is well established, the actual type of phase transitions and equilibrium conditions of their occurrence are, as of yet, poorly investigated. In the present study, samples of γ'-Fe4N and mixtures of α Fe and γ'-Fe4N powders have been heat-treated at temperatures between 250 and 1000 °C and pressures between 2 and 8 GPa in a multi-anvil press, in order to investigate phase equilibria involving the γ' phase. Samples heat-treated at high-pressure conditions, were quenched, subsequently decompressed, and then analysed ex situ. Microstructure analysis is used to derive implications on the phase transformations during the heat treatments. Further, it is confirmed that the Fe-N phases in the target composition range are quenchable. Thus, phase proportions and chemical composition of the phases, determined from ex situ X-ray diffraction data, allowed conclusions about the phase equilibria at high-pressure conditions.