Zobrazení zdroje stránky Velasquezmalloy2071

In micro/nano-scale systems where the characteristic length is in the order of or less than the mean free path for gas molecules, an object placed close to a heated substrate with a surface microstructure receives a propulsive force. In addition to the induced forces on the boundaries, thermally driven flows can also be induced in such conditions. As the force exerted on the object is caused by momentum brought by gas molecules impinging on and reflected at the surface of the object, reproducing molecular gas flows around the object is required to investigate the force on it. Using the direct simulation Monte Carlo (DSMC) method to resolve the flow, we found that by modifying the conventional ratchet-shaped microstructure into different configurations, a stronger propulsive force can be achieved. Specifically, the tip angle of the microstructure is an important parameter in optimizing the induced force. The increase in the propulsive force induced by the different microstructures was also found to depend on the Knudsen number, i.e., the ratio of the mean free path to the characteristic length and the temperature difference between the heated microstructure and the colder object. [https://www.selleckchem.com/products/cytosporone-b.html read more] Furthermore, we explained how this force is formed and why this force is enhanced by the decreasing tip angle, considering the momentum brought onto the bottom surface of the object by incident molecules.The recent development of micro-fabrication technologies has provided new methods for researchers to design and fabricate micro metal coils, which will allow the coils to be smaller, lighter, and have higher performance than traditional coils. As functional components of electromagnetic equipment, micro metal coils are widely used in micro-transformers, solenoid valves, relays, electromagnetic energy collection systems, and flexible wearable devices. Due to the high integration of components and the requirements of miniaturization, the preparation of micro metal coils has received increasing levels of attention. This paper discusses the typical structural types of micro metal coils, which are mainly divided into planar coils and three-dimensional coils, and the characteristics of the different structures of coils. The specific preparation materials are also summarized, which provides a reference for the preparation process of micro metal coils, including the macro-fabrication method, MEMS (Micro-Electro-Mechanical System) processing technology, the printing process, and other manufacturing technologies. Finally, perspectives on the remaining challenges and open opportunities are provided to help with future research, the development of the Internet of Things (IoTs), and engineering applications.An analytical model is presented that allows predicting the progress and the final depth obtained by laser micromachining of grooves in metals with ultrashort laser pulses. The model assumes that micromachined grooves feature a V-shaped geometry and that the fluence absorbed along the walls is distributed with a linear increase from the edge to the tip of the groove. The depth progress of the processed groove is recursively calculated based on the depth increments induced by successive scans of the laser beam along the groove. The experimental validation confirms the model and its assumptions for micromachining of grooves in a Ti-alloy with femtosecond pulses and different pulse energies, repetition rates, scanning speeds and number of scans.A fluorescence microscope is one of the most important tools for biomedical research and laboratory diagnosis. However, its high cost and bulky size hinder the application of laboratory microscopes in space-limited and low-resource applications. Here, in this work, we proposed a portable and cost-effective fluorescence microscope. Assembled from a set of 3D print components and a webcam, it consists of a three-degree-of-freedom sliding platform and a microscopic imaging system. The microscope is capable of bright-field and fluorescence imaging with micron-level resolution. The resolution and field of view of the microscope were evaluated. Compared with a laboratory-grade inverted fluorescence microscope, the portable microscope shows satisfactory performance, both in the bright-field and fluorescence mode. From the configurations of local resources, the microscope costs around USD 100 to assemble. To demonstrate the capability of the portable fluorescence microscope, we proposed a quantitative polymerase chain reaction experiment for meat product authenticating applications. The portable and low-cost microscope platform demonstrates the benefits in space-constrained environments and shows high potential in telemedicine, point-of-care testing, and more.In this current study, the validation and evaluation of a behavioral circuit model of electrostatic MEMS converters are presented. The main objective of such a model is to accurately find the converter behavior through the proper choice of its circuit elements. In this regard, the model enables the implementation of the electrostatic MEMS converter using commercially available off-shelf circuit elements. Thus, the overall vibration energy harvesting system can be implemented and tested without the need for fabricating the converter. As a result, the converter performance can be verified and evaluated before its fabrication which saves the expenses of fabricating trailed prototypes. To test the model, we apply it to an enhanced converter in which the conventional electrostatic MEMS converter is modified by depositing the tantalum pentoxide, Ta2O5, a high dielectric constant material, on its fingers' sidewalls. Such a deposition technique causes an appreciable increase in the overall converter capacitance and, in turn, the output power, which is boosted from the range of µw to the range of mW. Next, the converter behavioral circuit model, which is based on representing its capacitances variations with respect to the input displacement, x caused by the vibration signal, C-x curve, is built up. The model is qualitatively validated and quantitatively evaluated. The enhanced converter performance is investigated through the interaction of its model with the power conditioning circuit. From the simulation results, it is revealed that the converter behavioral circuit model accurately accomplishes the vibration energy conversion operation. As a result, the specification of the required controlling pulses for the converter operation is accurately determined. Finally, the model accuracy is validated by calibrating its performance with a traditionally simulated and fabricated electrostatic MEMS converter.We successfully achieved low-temperature assembly by reflowing the 13.5Sn-37.5Bi-45In-4Pb quaternary eutectic solder paste and the SAC 305 solder ball together at 140 °C for 5 min. The wetting angle of the mixed solder joint is 17.55°. The overall atomic percent of Pb in the mixed solder joint is less than 1%, which can be further reduced or eliminated. Moreover, after aging at 80 °C for 25 days, we observed no obvious decrease in shear strength of the fully mixed solder joint, which is the most advantage of this assembly technique over Sn58Bi solder assembly. The Bi phase segregation at the interface is slowed down compared with Sn-Bi solder joint. This low-temperature assembly is promising to be applied in advanced packaging technology to replace the eutectic Sn-Bi solder.This paper presents a novel microfluidic chip for upconcentration of sub-100 nm nanoparticles in a flow using electrical forces generated by a DC or AC field. Two electrode designs were optimized using COMSOL Multiphysics and tested using particles with sizes as low as 47 nm. We show how inclined electrodes with a zig-zag three-tooth configuration in a channel of 20 µm width are the ones generating the highest gradient and therefore the largest force. The design, based on AC dielectrophoresis, was shown to upconcentrate sub-100 nm particles by a factor of 11 using a flow rate of 2-25 µL/h. We present theoretical and experimental results and discuss how the chip design can easily be massively parallelized in order to increase throughput by a factor of at least 1250.We report the fabrication and optical characterization of Yb3+-doped waveguide amplifiers (YDWA) on the thin film lithium niobate fabricated by photolithography assisted chemo-mechanical etching. The fabricated Yb3+-doped lithium niobate waveguides demonstrates low propagation loss of 0.13 dB/cm at 1030 nm and 0.1 dB/cm at 1060 nm. The internal net gain of 5 dB at 1030 nm and 8 dB at 1060 nm are measured on a 4.0 cm long waveguide pumped by 976 nm laser diodes, indicating the gain per unit length of 1.25 dB/cm at 1030 nm and 2 dB/cm at 1060 nm, respectively. The integrated Yb3+-doped lithium niobate waveguide amplifiers will benefit the development of a powerful gain platform and are expected to contribute to the high-density integration of thin film lithium niobate based photonic chip.Antenna miniaturization technology has been a challenging problem in the field of antenna design. The demand for antenna miniaturization is even stronger because of the larger size of the antenna in the low-frequency band. In this paper, we consider MEMS magnetoelectric antennas based on mechanical resonance, which sense the magnetic fields of electromagnetic waves through the magnetoelectric (ME) effect at their mechanical resonance frequencies, giving a voltage output. A 70 μm diameter cantilever disk with SiO2/Cr/Au/AlN/Cr/Au/FeGaB stacked layers is prepared on a 300 μm silicon wafer using the five-masks micromachining process. The MEMS magnetoelectric antenna showed a giant ME coefficient is 2.928 kV/cm/Oe in mechanical resonance at 224.1 kHz. In addition, we demonstrate the ability of this MEMS magnetoelectric antenna to receive low-frequency signals. This MEMS magnetoelectric antenna can provide new ideas for miniaturization of low-frequency wireless communication systems. Meanwhile, it has the potential to detect weak electromagnetic field signals.Topological metamaterial has been a research hotpot in both physics and engineering due to its unique ability of wave manipulation. The topological interface state, which can efficiently and robustly centralize the elastic wave energy, is promising to attain high-performance energy harvesting. Since most of environmental vibration energy is in low frequency range, the interface state is required to be designed at subwavelength range. To this end, this paper developed a topological metamaterial beam with local resonators and studied its energy-harvesting performance. First, the unit cell of this topological metamaterial beam consists of a host beam with two pairs of parasitic beams with tip mass. Then, the band structure and topological features are determined. It is revealed that by tuning the distance between these two pairs of parasitic beams, band inversion where topological features inverse can be obtained. Then, two sub-chains, their design based on two topologically distinct unit cells, are assembled tond location. In other words, the piezoelectric transducer placed at the conjunction can maintain a stable and high-efficiency output power in the interface state, which makes the whole system very reliable in practical implementation.