Zobrazení zdroje stránky Slaterklitgaard4302

We reported an all-polarization-maintaining single-frequency ytterbium-doped bidirectional fiber laser for the first time, to the best of our knowledge. Single-frequency operation was achieved by a stable dynamic grating in the active fiber of a proper length owing to the bidirectional operation of the laser. The fiber laser possesses a linewidth of 7.43 kHz, a slope efficiency of 47.9%, and a great long-term stability.A cost-efficient and low-complexity optical input/output (I/O) packaging solution is a substantial challenge for volume production of photonic integrated circuits. To address this, metamaterial fiber couplers are an attractive solution for integrated photonic devices especially for optical I/O, interfacing standard optical fibers to photonic chips. They offer the advantages of refractive index engineering to achieve better mode match as well as higher fabrication tolerances. Metamaterial waveguides, as a fundamental building block of these fiber couplers, have attracted tremendous attention in recent years. Here, we report on effective optical return loss control in Si metamaterial waveguide designs to achieve ultra-low reflection loss in CMOS-compatible silicon photonics implemented in a 300 mm production line. Low backscattering is a substantial consideration for a range of applications. Here, a return loss of better than -30dB is achieved.We show that in the interference of two partially correlated scalar light beams, the fields can be divided into parts that are mutually completely correlated (coherent) and parts that are fully uncorrelated with the correlated parts and with each other. Such correlated and uncorrelated parts cannot, in general, be unambiguously specified, but with a certain additional constraint, the partition becomes unique and can be determined. We demonstrate experimentally that the uncorrelated contribution can be physically isolated with the help of a spatial unitary transformation, such as a nonabsorbing beam splitter. Our findings constitute foundational results on optical two-beam interferometry.We present a novel, to the best of our knowledge, form of polarization microscopy capable of producing quantitative optic-axis and phase retardation maps of transparent and anisotropic materials. The proposed method operates on differential phase-contrast (DPC) microscopy that produces a phase image of a thin specimen using multi-axis intensity measurements. For polarization-sensitive imaging, patterned illumination light is circularly polarized to illuminate a specimen. The light transmitted through a specimen is split into two orthogonal polarization states and measured by an image sensor. Subsequent DPC computation based on the illumination patterns, acquired images, and the imaging model enables the retrieval of polarization-dependent quantitative phase images, which are utilized to reconstruct the orientation and retardation of the specimen. We demonstrate the validity of the proposed method by measuring the optic-axis and phase retardation maps of calibrated and various anisotropic samples.We experimentally demonstrate, to the best of our knowledge, the first microdisk-based silicon-photonic mode-division (de)multiplexer circuit, which is compatible with wavelength-division multiplexing for high aggregate bandwidth on-chip optical communications. This circuit uses waveguide-wrapped microdisk resonators, featuring low levels of intermodal crosstalk and insertion loss within an ultracompact footprint. In addition, the proposed device presents an increased free spectral range, allowing for 530 combined data channels. [https://www.selleckchem.com/products/cilofexor-gs-9674.html see more] Furthermore, the microdisk structure naturally supports vertically oriented depletion-type pn junctions, which have been shown to reach subfemtojoule-per-bit modulation efficiencies. The high modulation efficiency, compactness, and wide free spectral range of waveguide-wrapped microdisk resonators present the potential for higher bandwidth and lower energy consumption in next-generation data processing and communication applications.We report on high-quality high-throughput laser milling of silicon with a sub-ps laser delivering more than 1 kW of average laser power on the workpiece. In order to avoid heat accumulation effects, the processing strategy for high-quality laser milling was adapted to the available average power by using five-pulse bursts, a large beam diameter of 372 µm to limit the peak fluence per pulse to approximately 0.7J/cm2, and a high feed rate of 24 m/s. As a result, smooth surfaces with a low roughness of Sa≤0.6µm were achieved up to the investigated milling depth of 313 µm while maintaining a high material removal rate of 230mm3/min.We demonstrate a C-band wavelength-tunable microlaser with an Er3+-doped high quality (∼1.8×106) lithium niobate microdisk resonator. With a 976 nm continuous-wave pump laser, lasing action can be observed at a pump power threshold lower than 400 µW at room temperature. Furthermore, the microdisk laser wavelength can be tuned by varying the pump laser power, showing a tuning efficiency of ∼-17.03pm/mW at low pump power below 13 mW, and 10.58 pm/mW at high pump power above 13 mW.Multiple-quantum well (MQW) III-nitride diodes can both emit and detect light. In particular, a III-nitride diode can absorb shorter-wavelength photons generated from another III-nitride diode that shares an identical MQW structure because of the spectral overlap between the emission and detection spectra of the III-nitride diode, which establishes a wireless visible light communication system using two identical III-nitride diodes. Moreover, a wireless light communication system using a modulating retro-reflector (MRR) enables asymmetric optical links, which forms a two-way optical link using a single transmitter and receiver. Here, in association with an MRR, we propose, fabricate, and characterize asymmetric optical links using monolithic III-nitride diodes, where one III-nitride diode functions as a transmitter to emit light, an MRR reflects light with the encoded information, another monolithically integrated III-nitride diode serves as a receiver to absorb the reflected light to convert optical signals into electrical ones, and the encoded information is finally decoded.