Zobrazení zdroje stránky Pennhorton5628

Regularized generalized canonical correlation analysis (RGCCA) is a general multiblock data analysis framework that encompasses several important multivariate analysis methods such as principal component analysis, partial least squares regression, and several versions of generalized canonical correlation analysis. In this article, we extend RGCCA to the case where at least one block has a tensor structure. This method is called multiway generalized canonical correlation analysis (MGCCA). Convergence properties of the MGCCA algorithm are studied, and computation of higher-level components are discussed. The usefulness of MGCCA is shown on simulation and on the analysis of a cognitive study in human infants using electroencephalography (EEG).Point-of-care facile and economical detection of Staphylococcus aureus (S. aureus), one of the main causes of food-borne illness, is highly demanded for the early diagnosis and control of infections. Herein, inspired by the proteolytic activity of S. aureus protease on a specific peptide substrate, we developed a rapid, simple and cost-effective biosensor for S. aureus using dual colorimetric and electrochemical detection on the same platform. In this approach, gold screen printed electrodes were used on which specific peptide sequences coupled to magnetic nanoparticles were immobilized giving the black color of the sensor surface. The addition of the S. aureus protease solution on the electrode surface causes cleavage of the peptide sequence and the release of the magnetic nanoparticles revealing the golden colour of the electrode which can be easily seen by the naked eye. Furthermore, square wave voltammetric signals can be detected on the same electrode in the ferro/ferricyanide redox couple. The change in the peak current after peptide cleavage was directly proportional to the concentration of S. aureus. The detection limit of the electrochemical assay was 3 CFU ml-1 after 1 min. Moreover, the biosensor was capable of specifically distinguishing S. aureus from other food- and water-borne bacteria such as E. coli and Listeria using the dual mode colorimetric and electrochemical detection. The biosensor was also tested in spiked milk and water samples showing very good recovery percentages. Thus, we believe that this dual mode biosensing platform enables the easy and accurate determination of S. aureus and holds great promise for point-of-care diagnosis.A contrast agent for X-ray micro computed tomography (μCT), called XlinCA, that combines reliable perfusion and permanent retention and contrast properties, was developed for ex vivo imaging. The new imaging agent XlinCA features high molecular weight, low viscosity and a high iodine content.Lipid membranes are ubiquitous biological organizers, required for structural and functional compartmentalization of the cell and sub-cellular organelles. Membranes in living cells are compositionally complex, comprising hundreds of dynamically regulated, distinct lipid species. Cellular physiology requires tight regulation of these lipidomic profiles to achieve proper membrane functionality. [https://www.selleckchem.com/products/17-AAG(Geldanamycin).html Tanespimycin] While some general features of tissue- and organelle-specific lipid complements have been identified, less is known about detailed lipidomic variations caused by cell-intrinsic or extrinsic factors. Here, we use shotgun lipidomics to report detailed, comprehensive lipidomes of a variety of cultured and primary mammalian membrane preparations to identify trends and sources of variation. Unbiased principle component analysis (PCA) shows clear separation between cultured and primary cells, with primary erythrocytes, synaptic membranes, and other mammalian tissue lipidomes sharply diverging from all cultured cell lines and also from one other. Most broadly, cultured cell membrane preparations were distinguished by their paucity of polyunsaturated lipids. Cultured mammalian cell lines were comparatively similar to one another, although we detected clear, highly reproducible lipidomic signatures of individual cell lines and plasma membrane (PM) isolations thereof. These measurements begin to establish a comprehensive lipidomic atlas of mammalian cells and tissues, identifying some major sources of variation. These observations will allow investigation of the regulation and functional significance of mammalian lipidomes in various contexts.The performance of an electronic device based on a two-dimensional material is strongly affected by the contact with the metallic electrodes. In this article, we study the electronic properties of two-dimensional MoSSe in contact with a germanene electrode by first-principles calculations. The results show that the contact characteristics are significantly different for the two sides of MoSSe. Notably, for both sides in-plane tensile strain induces a transition from Schottky to Ohmic behavior. Increasing the thickness of MoSSe also leads to an Ohmic contact. We propose an effective route to high performance MoSSe electronic devices.High-yield, chromatography-free syntheses of a ferrocene-templated molecular cage and its Pd-bearing derivative are presented. The formation of a symmetric cage-type structure was confirmed by single-crystal X-ray diffraction analysis. The Pd-bearing cage was used as an innovative catalyst for the efficient synthesis of 1,1'-biphenyls under mild conditions. The presented catalyst is reusable and 1,1'-biphenyls can be obtained efficiently in a gram scale process.This review discusses various bonding strategies for fabricating microfluidic devices, with a special emphasis on the modification of the surface assisted by the use of chemicals to assemble microfluidic devices under mild conditions such as room temperature and atmospheric pressure. The paper includes an overview of the wide ranges of bonding methods used in the fabrication of microfluidic systems, such as anodic bonding, fusion bonding, thermal bonding, solvent bonding, and surface chemical bonding. Among these, surface chemical bonding plays a crucial role between the polydimethylsiloxane (PDMS) and thermoplastics in order to assemble a microfluidic device in a simple and facile manner. The first section reviews relevant research on the sealing for microfluidic devices; in the second section, the materials used for device fabrication are reviewed. The third section discusses the different sealing processes used in the fabrication of microfluidic devices on silicon, glass, thermoplastic, and elastomer. Overall, this review concludes with a discussion on the importance of the surface chemical modification for bonding an elastomer - PDMS - with rigid materials at room temperature under atmospheric pressure and detailed discussions on their bond strengths.