Zobrazení zdroje stránky Guthriedolan4549

Poly(butylene succinate) (PBS) and poly(lactic acid) (PLA) were melt-blended and formed into a film by hot press forming. The film was selectively degraded by cutinase and proteinase K to form a porous material. The porous materials were characterized with respect to their pore morphology, pore size, porosity and hydrophilicity. The porous materials were investigated in vitro degradation and in vivo compatibility. The results show that the pore size of the prepared porous materials could be controlled by the proportion of PBS and the degradation time. When the PBS composition of PBS/PLA blends was changed from 40 wt% to 50 wt%, the mean pore diameter of the porous materials significantly increased from 6.91 µm to 120 µm, the porosity improved from 81.52% to 96.90%, and the contact angle decreased from 81.08° to 46.56°. In vitro degradation suggests that the PBS-based porous materials have a good corrosion resistance but the PLA-based porous materials have degradability in simulated body fluid. Subcutaneous implantation of the porous materials did not cause intense inflammatory response, which revealed good compatibility. The results of hematoxylin and eosin and Masson's trichrome staining assays demonstrated that the porous materials promote chondrocyte production. Porous materials have great potential in preparing implants for tissue engineering applications.High quality factor (High-Q) and transmission optical devices are required for various applications in the fields of physics and engineering. Critical for these applications is the realization of a structure with high-Q, complete transmission and small volume. A robust high-Q filter with complete transmission by conjugated topological photonic crystals (CTPC) is presented. The study shows that an ultra-high-Q of more than 108 with complete transmission is obtained by the CTPC with 2 μm long due to the excitation of conjugated topological edge-states (CTES). It is also found that even though the quality factor of resonances increases as the periodic number of multilayers increases, these resonances are still complete transmission. A novel concept of CTES is first proposed in this study and investigated the effect of its topological phenomenon on high quality factor via CTPC. We theoretically realize the robust high-Q and complete transmission in the CTPC, which is different from those in periodic, quasi-periodic, Fabry-Perot photonic crystals and traditional topological photonic crystals (TPC).Although autografts are considered to be the gold standard treatment for reconstruction of large bone defects resulting from trauma or diseases, donor site morbidity and limited availability restrict their use. Successful bone repair also depends on sufficient vascularization and to address this challenge, novel strategies focus on the development of vascularized biomaterial scaffolds. This pilot study aimed to investigate the feasibility of regenerating large bone defects in sheep using 3D-printed customized calcium phosphate scaffolds with or without surgical vascularization. Pre-operative computed tomography scans were performed to visualize the metatarsus and vasculature and to fabricate customized scaffolds and surgical guides by 3D printing. Critical-sized segmental defects created in the mid-diaphyseal region of the metatarsus were either left empty or treated with the 3D scaffold alone or in combination with an axial vascular pedicle. Bone regeneration was evaluated 1, 2 and 3 months post-implantation. After 3 months, the untreated defect remained non-bridged while the 3D scaffold guided bone regeneration. The presence of the vascular pedicle further enhanced bone formation. Histology confirmed bone growth inside the porous 3D scaffolds with or without vascular pedicle inclusion. Taken together, this pilot study demonstrated the feasibility of precised pre-surgical planning and reconstruction of large bone defects with 3D-printed personalized scaffolds.An amendment to this paper has been published and can be accessed via a link at the top of the paper.Semen quality is affected by environmental factors, endocrine function abnormalities, and genetic factors. A GWAS recently identified ERBB4 at 2q34 as a genetic locus associated with sperm motility. However, GWASs for human semen volume and sperm concentration have not been conducted. In addition, testis size also reportedly correlates with semen quality, and it is important to identify genes that affect testis size. Reproductive hormones also play an important role in spermatogenesis. To date, genetic loci associated with plasma testosterone, sex hormone-binding globulin (SHBG), follicle-stimulating hormone (FSH), and luteinizing hormone (LH) levels have been identified using GWASs. However, GWASs have not identified any relevant loci for plasma inhibin B levels. We conducted a two-stage GWAS using 811 Japanese men in a discovery stage followed by a replication stage using an additional 721 Japanese men. The results of the discovery and replication stages were combined into a meta-analysis. After setting a suggestive significance threshold for P values  less then  5 × 10-6　in the discovery stage, we identified ten regions with SNPs (semen volume one, sperm concentration three, testes size two, and inhibin B four). We selected only the most significant SNP in each region for replication genotyping. Combined discovery and replication results in the meta-analysis showed that the locus 12q21.31 associated with plasma inhibin B levels (rs11116724) had the most significant association (P = 5.7 × 10-8). The LRRIQ1 and TSPAN19 genes are located in the 12q21.31 region. [https://www.selleckchem.com/products/corticosterone.html Corticosterone in vitro] This study provides new susceptibility variants that contribute to plasma inhibin B levels.The ubiquitin-proteasome system is the principal system for protein degradation mediated by ubiquitination and is involved in various cellular processes. Cullin-RING ligases (CRL) are one class of E3 ubiquitin ligases that mediate polyubiquitination of specific target proteins, leading to decomposition of the substrate. Cullin 3 (CUL3) is a member of the Cullin family proteins, which act as scaffolds of CRL. Here we describe three cases of global developmental delays, with or without epilepsy, who had de novo CUL3 variants. One missense variant c.854T&gt;C, p.(Val285Ala) and two frameshift variants c.137delG, p.(Arg46Leufs*32) and c.1239del, p.(Asp413Glufs*42) were identified by whole-exome sequencing. The Val285 residue located in the Cullin N-terminal domain and p.Val285Ala CUL3 mutant showed significantly weaker interactions to the BTB domain proteins than wild-type CUL3. Our findings suggest that de novo CUL3 variants may cause structural instability of the CRL complex and impairment of the ubiquitin-proteasome system, leading to diverse neuropsychiatric disorders.