Zobrazení zdroje stránky Dunnjuarez6034

The CPN-STA model also brings out a hitherto unreported structure in rāgas and explains the precision obtained using the previous techniques.An accurate solution of the wave equation at a fluid-solid interface requires a correct implementation of the boundary condition. Boundary conditions at fluid-solid interface require continuity of the normal component of particle velocity and traction, whereas the tangential components vanish. A main challenge is to model interface waves, namely, the Scholte and leaky Rayleigh waves. This study uses a nodal discontinuous Galerkin (dG) finite-element method with the medium discretized using an unstructured uniform triangular meshes. [https://www.selleckchem.com/products/scriptaid.html selleck] The natural boundary conditions in the dG method are implemented by (1) using an explicit upwind numerical flux and (2) by using an implicit penalty flux and setting the modulus of rigidity of the acoustic medium to zero. The accuracy of these methods is evaluated by comparing the numerical solutions with analytical ones, with source and receiver at and away from the interface. The study shows that the solutions obtained from the explicit and implicit boundary conditions provide the correct results. The stability of the dG scheme is determined by the numerical flux, which also implements the boundary conditions by unifying the numerical solution at shared edges of the elements in an energy stable manner.Distortion product otoacoustic emission (DPOAE) maps collect DPOAE emissions over a broad range of frequencies and ratios. One application of DPOAE mapping could be monitoring changes in intracranial pressure (ICP) in space, where non-invasive measures of ICP are an area of interest. Data were collected in two experiments to statistically assess changes in DPOAE maps. A repeatability study where four maps per subject were collected across four weeks to establish "normal" variability in DPOAE data, and a posture study where subjects were measured supine and prone with lower body negative pressure, lower body positive pressure (LBPP), and at atmospheric pressure. DPOAE amplitude maps were analyzed using statistical parametric mapping and random field theory. Postural changes produced regional changes in the maps, specifically in the range of 5-7.5 kHz and between primary tone ratios of 1.13-1.24. These regional changes were most pronounced in the prone LBPP condition, where amplitudes were lower from baseline for the Postural Cohort than the Repeatability Cohort. Statistical parametric mapping provided a sensitive measure of regional DPOAE map changes, which may be useful clinically to monitor ICP noninvasively in individuals or for research to identify differences within in cohorts of people.Concern over the impacts of anthropogenic noise on aquatic fauna is increasing, as is the number of vessels in the world's oceans, lakes, and rivers. Sound signatures of different vessel types are increasingly characterized, yet few reports are available on solar-electric powered vessels. Such data are important to model the sound levels experienced by marine fauna and their potential impacts. Sounds from two vessel types were recorded in the shallow waters of the Swan River, Western Australia, using bottom-mounted OceanInstruments SoundTraps. Multiple passes from two 10-m solar-electric powered passenger ferries and, for comparison, two 25-m conventionally powered (inboard diesel engine) passenger ferries were selected. Analysis was conducted on 58 and 16 passes by the electric ferries (in 2016 and 2017-2018, respectively) and 10 and 14 passes by the conventional ferry (2016 and 2017-2018, respectively) at 5-m range. At 55-m range, analysis was conducted on 17 and 1 passes by the electric ferry (2016 and 2017-2018, respectively) and 9 and 3 passes of the conventional ferry (2016 and 2017-2018, respectively). Measured received levels and modeled sound propagation were then used to estimate monopole source levels (MSL) and radiated noise levels (RNL). At 55-m range, the conventionally powered ferry type produced 156 and 157 dB re 1 μPa2m2 MSL and RNL, respectively, while the same metrics for the electric ferry were 12 dB lower. At frequencies below 500 Hz, spectral levels of the electric ferry at a range of less then 5 m were 10-25 dB lower than those of the conventional ferry, implying a potential benefit for animals that use low-frequency communication, if electric motors replaced petrol or diesel engines.As the understanding of the possible impacts of anthropogenic underwater sound has increased, so have efforts been designed to reduce the effects to marine species and habitats. Consequently, over the last decade, a large number of new policies, regulations, and joint efforts to reduce anthropogenic sound and mitigate affects to aquatic life have been introduced internationally. The United States, Canada, the EU, and many regional and multinational organizations have implemented regulations governing underwater anthropogenic sound. While habitat-centric policies have been developed internationally, difficulty in implementing these highlights the need for additional research including efforts to monitor over longer temporal scales, assess impacts to estuarine and freshwater environments, obtain baseline data where possible, and better understand impacts of chronic noise on individual fitness and population health. This paper reviews the developments in policy focused on reducing the impacts of anthropogenic impacts on aquatic habitats and makes recommendations on research efforts required to manage the impact of underwater anthropogenic sound on habitats.To determine sound absorption coefficients of fine granular materials, the materials must be cased to suppress their flowability. In this study, effects of casing on the sound absorption coefficients of fine granular materials were investigated. The normal incidence sound absorption coefficients of cased hollow glass beads were measured using cylindrical impedance tubes. The measurement results demonstrated that the hollow glass beads present a sound absorption peak, which was attributed to the vibration of a particle frame, in the frequency range of 180 to 700 Hz for sample thickness in the range of 20 to 550 mm. With an increase in the material thickness or diameter of the casing, the first peak of the sound absorption coefficients shifted to a lower frequency. The sound absorption coefficients were calculated using an elastic frame model for porous materials. The effects of friction between the lateral wall of the case and the particle frame were incorporated in the bulk modulus and bulk density of the particle frame in the model.