Zobrazení zdroje stránky Duelundlindgreen8808

OBJECTIVES To assess the association of cholecystectomy with the risk of prostate cancer in patients with gallstones. METHODS This nationwide population-based cohort study was conducted by retrieving the Longitudinal Health Insurance Research Database (LHID2000) for inpatient claims in the Taiwan National Health Insurance (NHI) program. The study cohort consisted of 72,606 men aged 20 years with gallstones undergoing cholecystectomy between 2000 and 2010. The control cohort consisted of the men with gallstones, but without cholecystectomy, by 11 propensity score matching with the study cohort based on age, sex, urbanization, occupation, comorbidities, and the index date. We compared the hazard ratio of prostate cancer between both of the cohorts. RESULTS The incidence of prostate cancer was 0.76/1000 person-years for the non-cholecystectomy cohort and 1.28/1000 person-years for the cholecystectomy cohort [aHR (adjusted hazard ratio) = 1.67, 95% confidence interval (CI = 1.45-1.92), respectively (p 5 years, respectively. CONCLUSIONS Cholecystectomy is associated with an increased hazard ratio of prostate cancer in gallstones patients, and the risk increases with an incremental period of follow-up. This observational study cannot ascertain the detrimental mechanisms of cholecystectomy for the development of prostate cancer, and cholecystectomy is not recommended for the prevention of prostate cancer based on our study.Methicillin-resistant Staphylococcus aureus (MRSA) is a serious and rapidly growing threat to human beings. [https://www.selleckchem.com/ selleck kinase inhibitor] Emodin has a potent activity against MRSA; however, its usage is limited due to high hydrophobicity and low oral bioavailability. Thus, the coaxial electrospinning nanofibers encapsulating emodin in the core of hydrophilic poly (vinylpyrrolidone), with a hygroscopic cellulose acetate sheath, have been fabricated to provide long-term effect against MRSA. Scanning electron microscopy and transmission electron microscopy confirmed the nanofibers had a linear morphology with nanometer in diameter, smooth surface, and core-shell structure. Attenuated total reflection-Fourier transform infrared spectra, X-ray diffraction patterns, and differential scanning calorimetric analyses verified emodin existed in amorphous form in the nanofibers. The nanofibers have 99.38 ± 1.00% entrapment efficiency of emodin and 167.8 ± 0.20 % swelling ratio. Emodin released from nanofibers showed a biphasic drug release profile with an initial rapid release followed by a slower sustained release. CCK-8 assays confirmed the nontoxic nature of the emodin-loaded nanofibers to HaCaT cells. The anti-MRSA activity of the nanofibers can persist up to 9 days in AATCC147 and soft-agar overlay assays. These findings suggest that the emodin-loaded electrospun nanofibers with core-shell structure could be used as topical drug delivery system for wound infected by MRSA.This work is a pioneer attempt to fabricate quasi-solid dye-sensitized solar cell (QSDDSC) based on organosoluble starch derivative. Rheological characterizations of the PhSt-HEC blend based gels exhibited viscoelastic properties favorable for electrolyte fabrication. From amplitude sweep and tack test analyses, it was evident that the inclusion of LiI improved the rigidity and tack property of the gels. On the other hand, the opposite was true for TPAI based gels, which resulted in less rigid and tacky electrolytes. The crystallinity of the gels was found to decline with increasing amount of salt in both systems. The highest photoconversion efficiency of 3.94% was recorded upon addition of 12.5 wt % TPAI and this value is one of the highest DSSC performance recorded for starch based electrolytes. From electrochemical impedance spectroscopy (EIS), it is deduced that the steric hindrance imposed by bulky cations aids in hindering recombination between photoanode and electrolyte.This paper reports a novel composite-based processing route for improving the electrical performance of Ca3Co4O9 thermoelectric (TE) ceramics. The approach involves the addition of metallic Co, acting as a pore filler on oxidation, and considers two simple sintering schemes. The (1-x)Ca3Co4O9/xCo composites (x = 0%, 3%, 6% and 9% vol.) have been prepared through a modified Pechini method, followed by one- and two-stage sintering, to produce low-density (one-stage, 1ST) and high-density (two-stage, 2ST) ceramic samples. Their high-temperature TE properties, namely the electrical conductivity (σ), Seebeck coefficient (α) and power factor (PF), were investigated between 475 and 975 K, in air flow, and related to their respective phase composition, morphology and microstructure. For the 1ST case, the porous samples (56%-61% of ρth) reached maximum PF values of around 210 and 140 μWm-1·K-2 for the 3% and 6% vol. Co-added samples, respectively, being around two and 1.3 times higher than those of the pure Ca3Co4O9 matrix. Although 2ST sintering resulted in rather dense samples (80% of ρth), the efficiency of the proposed approach, in this case, was limited by the complex phase composition of the corresponding ceramics, impeding the electronic transport and resulting in an electrical performance below that measured for the Ca3Co4O9 matrix (224 μWm-1·K-2 at 975K).Alumina is an advanced ceramic with applications in dental and medical sciences. Since ceramics are hard and brittle, their conventional machining is expensive, arduous, and time-consuming. As rotary ultrasonic machining is among the most adequate and proficient processing techniques for brittle materials like ceramics. Therefore, in this study, rotary ultrasonic drilling (RUD) has been utilized to drill holes on alumina ceramic (Al2O3). This study investigates the effect of key RUD process variables, namely vibration frequency, vibration amplitude, spindle speed, and feed rate on the dimensional accuracy of the drilled holes. A four-variable three-level central composite design (thirty experiments on three sample plates) is utilized to examine the comparative significance of different RUD process variables. The multi-objective genetic algorithm is employed to determine the optimal parametric conditions. The findings revealed that material removal rates depend on feed rate, while the cylindricity of the holes is mostly controlled by the speed and feed rate of the spindles.