Zobrazení zdroje stránky Dodsoncastaneda4920

The limit of the holography diagnostic's x-y spatial resolution was characterized by comparison with scanning electron microscope imaging.Three-dimensional reconstruction algorithms have been developed, which determine the hot-spot velocity, hot-spot apparent ion temperature distribution, and fuel areal-density distribution present in laser-direct-drive inertial confinement fusion implosions on the OMEGA laser. These reconstructions rely on multiple independent measurements of the neutron energy spectrum emitted from the fusing plasma. Measurements of the neutron energy spectrum on OMEGA are made using a suite of quasi-orthogonal neutron time-of-flight detectors and a magnetic recoil spectrometer. These spectrometers are positioned strategically around the OMEGA target chamber to provide unique 3D measurements of the conditions of the fusing hot spot and compressed fuel near peak compression. The uncertainties involved in these 3D reconstructions are discussed and are used to identify a new nTOF diagnostic line of sight, which when built will reduce the uncertainty in the hot-spot apparent ion temperature distribution from 700 to less then 400 eV.A Fast Fourier Transform (FFT) based method has been developed, which improves the frequency response of the Motional Stark Effect (MSE) system by about a factor of 10 over the conventional analog lock-in method. The method uses fits to rigorously derived analytic expressions for the FFT spectral components of the MSE signal to accurately obtain the amplitudes and phases of the 2f1 and 2f2 photo-elastic modulator (PEM) frequencies that encode the polarization angle. Since no frequency filtering is used in the FFT method, the frequency response is limited by fundamental measurement properties the frequency response of the detector, photon statistics, sample rate, and the ability to resolve the spectral components. In contrast, the frequency response of the analog lock-in is limited by a low pass filter with a cutoff of around 500 Hz. In the case of the DIII-D MSE system, the output of the photo-multiplier tube detector was sampled at 500 kHz and FFTs with as few as 100 points were used to obtain the amplitudes of the 2f1 and 2f2 PEM frequency components. This corresponds to a frequency response of 5 kHz, about ten times faster than the analog lock-in amplifier system. Details of the FFT method will be presented and compared to those of the analog lock-in system.Understanding how the surfaces of airless planetary bodies-such as the Moon-scatter visible light enables constraints to be placed on their surface properties and top boundary layer inputs to be set within thermal models. Remote sensing instruments-such as Diviner onboard the Lunar Reconnaissance Orbiter-measure thermal emission and visible light scattering functions across visible (∼0.38-0.7 µm) to thermal infrared (TIR) wavelengths (∼0.7-350 μm). To provide ground support measurements for such instruments, the Oxford Space Environment Goniometer (OSEG) was built. Initially, the OSEG focused on measuring TIR directional emissivity functions for regolith and regolith simulant samples in a simulated space environment, but it has recently been modified to measure visible wavelength Bidirectional Reflectance Distribution Functions (BRDFs) of samples in ambient conditions. Laboratory-measured BRDFs can be used (1) to test and to help interpret models-such as the Hapke photometric model-and (2) as visible scattering function inputs for thermal models. This paper describes the modifications to and initial calibration measurements taken by the Visible Oxford Space Environment Goniometer with a 532 nm laser, and details how this setup can be used to measure BRDFs of regolith and regolith simulant samples of airless planetary bodies.A Hall sensor array system for magnetic field detection and analysis is realized in X-FAB 0.18 μm CMOS technology. [https://www.selleckchem.com/products/ldc7559.html LDC7559 manufacturer] Magnetic field detection is attributed to the magnetization of metal coils to metal particles and the sensing characteristics of the Hall sensor array. The system puts forward a complete solution from Hall sensors, analog front-end circuit, analog-to-digital converter (ADC) to microcontroller unit. Using Ansoft Maxwell and COMSOL Multiphysics software for simulation verification, the minimum diameter of magnetic particles that can be detected in the system is 2 μm. The measured signal to noise and distortion ratio, spurious free dynamic range, and effective number of bits of the proposed ADC are 70.61 dB, 90.08 dB, and 11.44-bit, respectively. The microsystem based on STM32 combines hardware and software design, which can effectively adjust the motion parameters and realize the real-time display in the LCD screen of the magnetic field and voltage information. Compared to the prior system, the portability, cost, and efficiency have been considerably improved, which is aimed at the rapid measurement of heavy metal particles such as Fe, Co, and Ni in ambient air and blood.Narrowband microwave filters have wide ranging applications, including the reduction in phase noise of microwave sources within a given frequency band. The prospect of developing an automated filter that tunes itself to an arbitrary desired frequency at maximum extinction promises many experimental advantages such as an enhanced efficiency in performing fine frequency detuning scans and saving time and effort as compared to manual tuning. We design, construct, and program such an automated system and present its hardware and software for reproducibility. It consists of a cylindrical cavity filter and two motors, which change the cavity length and the coupling strength of the microwave field into the cavity, respectively. By measuring the cavity response, an algorithm implemented in Python optimizes these two parameters to achieve the tuning of the filter cavity to the desired frequency with a precision of around 20 kHz, which is significantly better than the cavity linewidth (∼1 MHz). We also demonstrate the suppression of phase noise at the desired frequency by more than 10 dB.Background Strong opioids are mainly utilized to attenuate pain in cancer patients. Adherence to analgesic drugs significantly promotes adequate pain management and improves quality of life. We aimed to identify the factors influencing non-adherence to strong opioids in cancer patients. Methods A descriptive, cross-sectional, two-phased, mixed methods design was conducted prospectively to evaluate a cohort of 101 cancer patients who are currently prescribed strong opioids from a pain clinic in Thailand between January and March 2018. Participants were asked to complete a questionnaire that included the following sections general characteristics; the Medication Taking Behavior in Thai (MTB-Thai) for assessing adherence to medications; and factors influencing nonadherence, which were analyzed using multivariate logistic regression. In addition, face-to-face in depth interviews were conducted with patients showing non-adherence to strong opioids (MTB-Thai score ≤21) and analyzed using thematic content analysis. Results Of 101 cancer pain patients that completed the questionnaire, 39.