Zobrazení zdroje stránky Brandtbraun9033

04 mm by SEM test. By comparing with the experimental data, the accuracy of the analytical solution is confirmed. Finally, the impact of aggregate shape on chloride diffusivity is discussed. The analytical results show that the chloride diffusivity has a reduction with the increase of aggregate content or decrease of aspect ratio.Bayer red mud (BRM) is a kind of solid waste with high hematite content, and its effective utilization is difficult due to the special physicochemical properties. In this work, Fe2O3 in BRM was reduced to Fe3O4 by biomass, and iron concentrate and high activity tailings were obtained after magnetic separation. The pozzolanic activity and hydration characteristics of the tailings were systematically studied. The results showed that the relatively stable polymerization structures of Si-O and Al-O in BRM are destroyed under the effect of biomass reduction at 650 °C, and some fracture bonds and activation points are formed in the structures. [https://www.selleckchem.com/products/ABT-263.html Navitoclax nmr] The aluminosilicate phases in the BRM were easy to transform into the active substances of Si and Al. The pozzolanic activity of tailings is greatly improved, and its pozzolanic activity index is 91%. High polymerization degree of gel and ettringite are formed since more active substances and alkali in the tailings promote the hydration reaction of cement-based cementitious materials, which made cementitious materials have dense matrix, good mechanical properties, and environmental performance. This work has realized the full quantitative utilization of BRM and provided a feasible way for the resource utilization of BRM.Despite the ideal performance demonstrated by mixed perovskite materials when used as active layers in photovoltaic devices, the factor which still hampers their use in real life remains the poor stability of their physico-chemical and functional properties when submitted to prolonged permanence in atmosphere, exposure to light and/or to moderately high temperature. We used high resolution photoelectron spectroscopy to compare the chemical state of triple cation, double halide Csx(FA0.83MA0.17)(1-x)Pb(I0.83Br0.17)3 perovskite thin films being freshly deposited or kept for one month in the dark or in the light in environmental conditions. Important deviations from the nominal composition were found in the samples aged in the dark, which, however, did not show evident signs of oxidation and basically preserved their own electronic structures. Ageing in the light determined a dramatic material deterioration with heavily perturbed chemical composition also due to reactions of the perovskite components with surface contaminants, promoted by the exposure to visible radiation. We also investigated the implications that 2D MXene flakes, recently identified as effective perovskite additive to improve solar cell efficiency, might have on the labile resilience of the material to external agents. Our results exclude any deleterious MXene influence on the perovskite stability and, actually, might evidence a mild stabilizing effect for the fresh samples, which, if doped, exhibited a lower deviation from the expected stoichiometry with respect to the undoped sample. The evolution of the undoped perovskites under thermal stress was studied by heating the samples in UHV while monitoring in real time, simultaneously, the behaviour of four representative material elements. Moreover, we could reveal the occurrence of fast changes induced in the fresh material by the photon beam as well as the enhanced decomposition triggered by the concurrent X-ray irradiation and thermal heating.In an attempt to incorporate tin (Sn) into high-entropy alloys composed of refractory metals Hf, Nb, Ti and Zr with the addition of 3d transition metals Cu, Fe, and Ni, we synthesized a series of alloys in the system HfTiZrSnM (M = Cu, Fe, Nb, Ni). The alloys were characterized crystallographically, microstructurally, and compositionally, and their physical properties were determined, with the emphasis on superconductivity. All Sn-containing alloys are multi-phase mixtures of intermetallic compounds (in most cases four). A common feature of the alloys is a microstructure of large crystalline grains of a hexagonal (Hf, Ti, Zr)5Sn3 partially ordered phase embedded in a matrix that also contains many small inclusions. In the HfTiZrSnCu alloy, some Cu is also incorporated into the grains. Based on the electrical resistivity, specific heat, and magnetization measurements, a superconducting (SC) state was observed in the HfTiZr, HfTiZrSn, HfTiZrSnNi, and HfTiZrSnNb alloys. The HfTiZrSnFe alloy shows a partial SC transition, whereas the HfTiZrSnCu alloy is non-superconducting. All SC alloys are type II superconductors and belong to the Anderson class of "dirty" superconductors.Cuprorivaite, also known as Egyptian blue (EB), CaCuSi4O10, has been utilized as an important blue pigment for thousands of years. It shows a 430-800 nm broad excitation band and an intense 910-920 nm near-infrared (NIR) emission peak at room temperature. The application that motivates the current research is for luminescent solar concentrator (LSC) usage. Current technology for this purpose relies on high near-infrared reflectance. This article addresses the investigation of the relationship between dispersing methods and photoluminescence (PL) intensity. Mechanical grinding methods investigated in the study were horizontal bead mill, exfoliation and three-roll mill. The initial aim of the study was to verify if the proposed methods do not damage PL. To the surprise of the authors, three-roll mill treatment enhanced PL by nearly 50% without altering the morphology of the powder. An X-ray diffraction study suggested slight alterations in the crystal lattice.The study assessed the effect of ion nitriding on the properties of the surface layer of Grade 5 titanium alloy used, among others, in medicine. Titanium and its alloys have low hardness and insufficient wear resistance in conditions of friction which limits the use of these materials. The improvement of these properties is only possible by the appropriate modification of the surface layer of these alloys. The ion nitriding process was carried out in a wide temperature range, i.e., 530-590 °C, and in the time range 5-17 h. Two variants of nitriding were applied cathodic (conventional) nitriding and nitriding using the active screen method. The research results presented in this article allow for stating that each of the applied nitriding variants improves the analysed properties (nitrogen diffusion depth, hardness, wear resistance, microstructure analysis and surface topography) of the surface layers in relation to the material before nitriding. The hardness increased in every nitriding variant (the use of the additional active screen increased the hardness to 1021 HK0.